Miele H 5240 B Manual

Catalytic enamel surfaces
The back panel, roof liner and side
panels (if fitted) are coated with dark
grey catalytic enamel.
Soiling from oil and fat is burnt off these
surfaces when very high temperatures
are used in the oven. The higher the
temperature, the more effective the
process.
The catalytic coating becomes
ineffective through using
– abrasive cleaning agents,
– hard brushes or abrasive
sponges,
– oven sprays.
Remove the catalytic back panel,
side panels and roof liner from the
oven before...

To remove the oven door
The oven door is connected to the oven
by hinges.
Before removing the door, the locking
clamps on both hinges have to be
released.
Open the door fully.

To release the locking clamps on the
hinges turn them upwards as far as
they will go until they are at an angle.
See illustration.Then lift the door upwards as far as it
will go.
Do not attempt to take the door off
the hinge guides when it is in a
horizontal position. The guides will
close, and damage the appliance.
Danger of...

To dismantle the oven door
If condensate has worked its way in
between the glass panes, the door can
be dismantled in order to clean in
between the panes.
Do not use scouring agents, hard
sponges or brushes or sharp metal
tools to clean glass as these can
scratch the surface. Scratches can
also cause the glass to break.
Do not use an oven spray. This will
damage the surface of the
aluminium surrounds.
Ensure that the glass panes are
inserted the correct way round after
cleaning as each side of the pane...

Gentlylift the inner pane up and out
of the plastic strip.

Gently lift the middle pane and
remove it together with the seal.

Remove the seal from the pane.Clean the glass panes and other
parts with a Miele E-cloth or a clean
sponge and a solution of hot water
with a little washing-up liquid. Wipe
dry using a soft cloth.
To refit the door:
To make sure that the middle pane
is put back in the correct way, one
of the corners of the pane is more
angled than the others. The more
angled corner must be...

Refit the middle pane and the seal.
The more angled corner must be at
the top left.

Push the inner pane into the plastic
strip and place it between the
retainers.
"Miele" must be visible at the top.Flip the glass pane retainers inwards
to close them.
Cleaning and care
55 

To refit the door
Hold the door securely at both sides
and carefully fit it back onto the hinge
guides.
Make sure that the door goes back
on straight.Open the door fully.
Flip both locking clamps back up as
far as they will go into a horizontal
position.
It is essential that the locking clamps
are flipped down when the door is
refitted after cleaning. Otherwise the
hinges could work loose, resulting in
damage to the door.
Cleaning and care
56 

To remove the runners
Make sure the oven heating
elements are switched off and cool.
Danger of burning.
Pull the runners forwards out of the
holder and remove.
If applicable, also remove the
catalytic side panels attached to the
runners.
Reassemble in the reverse order,
carefully ensuring all parts are correctly
in place.
To remove the catalytic
enamelled back panel, side
panels and roof liner
Make sure the oven heating
elements are switched off and cool.
Danger of burning.
See "Cleaning and...

Roof liner (if fitted)
Remove the runners, together with
the catalytic side panels (if fitted).
Unscrew the wing nut.
Gently lower the element.
Do not use force to pull it down as
this can cause the element to break.
Take out the roof liner.
Reassemble in the reverse order,
carefully ensuring all parts are correctly
in place.
Make sure that the wing nut is
screwed back on properly.Side panels (if fitted)
Remove the runners, together with
the catalytic side panels.
Remove the side panels from the...

With the aid of the following guide, minor problems can be easily corrected
without contacting Miele.
Do not attempt to open the appliance casing yourself!
Installation, maintenance and repairs may only be carried out by a suitably
qualified and competent person in strict accordance with current national and
local safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
Problem Possible cause and remedy
The...

Problem Possible cause and remedy
The interior lamp is
not working.Disconnect the appliance from the electricity supply:
Switch off and unplug at the socket, or disconnect the
fuse, or switch off at the isolator as appropriate.
Turn the lamp cover a quarter turn anti-clockwise to
release it and then pull it downwards to take it out.
Replace it with a new lamp (Osram 66275 AM, 230 V,
25 W, G9).
Refit the lamp cover and turn it clockwise to secure it.
Reconnect the appliance to the mains electricity...