Miele G665 Owners Manual
Here you can view all the pages of manual Miele G665 Owners Manual. The Miele manuals for Dishwasher are available online for free. You can easily download all the documents as PDF.
Page 61
Trimming the toekick The rear of the toekick has two cutting lines. Screw the toekick onto the installed brackets, with the cutting lines to- wards the top, and pull out evenly until it aligns with the toekick of the adjoining cabinets. The toekick cannot be pushed back in. It must be unscrewed, so that the tension on the spring clips can be released. The brackets can then be pushed in, and the toekick re-attached. Carefully open the dishwasher door until it hits the toekick. Using the front lower edge...
Page 62
Electrical connection It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances. Disconnect the appliance from the power supply before servicing the ma- chine by pulling the plug or turning off the circuit breaker. Specifications. Power Supply: 120 VAC, 60 Hz Rated Load: 12.5 A / 1500 W Circuit breaker:15 AMPS The unit is equipped with a 5 ft (1.5 m)...
Page 63
Permanent Connection (Hard Wiring). For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dish- washer, behind the toekick and service panel. Pass the permanent power sup- ply cable through the strain relief and secure it to the terminal box. Connect: L1 (Black) to L on terminal block N (White) to N on terminal block GRND To ground connector GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal, permanent wiring system,...
Page 64
Plumbing It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances. To help protect your home, all dish- washers that carry the following blue and white sticker are designed to shut off the water and drain the wash cham- ber in the rare event of an internal water valve failure. In order for this function to be active, the door must be tightly shut, a...
Page 65
Existing plumbing: If the standard 3/8 copper plumbing for a dishwasher already exists with a compression fitting and valve as pic- tured: Cut the 3/8 copper tubing after the valve. Install the 3/8 compression to 3/4 MHT (Male Hose Thread) adapter (supplied with the machine), as illus- trated. Connect the inlet hose to the existing valve/adapter assembly. Electrical wiring and components should not come into contact with any plumbing fixtures or hoses. Do not, under any circumstances, cut the intake...
Page 66
Drain system specifications: The machine comes equipped with: – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of 7/8 (22 mm). – A built-in swivel connector which allows the drain hose to be routed in any direction. – A built in non-return valve on the dis- charge side to prevent waste water from flowing back into the dish- washer. – A built-in odor trap on the discharge side to prevent odors from entering the kitchen. Maximum drain height: 3 ft (1 m) Maximum drain hose length: 12...
Page 67
Venting the drainage system Only if the dishwasher drain hose is connected to a floor drain or to a drain pipe that is below the level of the lower baskets wheels, the drain must be vented; otherwise the water in- side of the dishwasher may siphon out during the course of a wash program. Vent the drain: Open the dishwasher door. Cut off the vent cap located at the right rear of the dishwasher, behind the filters, as illustratedAdditional note. Since all Miele dishwashers are equipped with an odor trap...
Page 68
Technical Data Height 32 1/4 (82 cm) adjustable to 34 7/8 (88.6 cm) Width 23 1/2 (59.8 cm) Width of opening 23 5/8 (60 cm) Depth 22 1/2 (57 cm) U and i models Depth with door open 45 1/2 (116 cm) U and i models Weight approx. 115 Ibs (52 kg) Voltage 110/120 V AC Rated load 12.5 A / 1500 W Fuse rating 15 A Water pressure 14.5 - 145 psi (1 - 10 bar) Hot water connection 120°F (49°C ) (max 140°F (60°C)) Drain height 3 ft (1 m) maximum Drain length 12 ft (3.5 m) maximum Power cord length approx. 5...