Miele G665 Owners Manual

Checking the water level
Checking the water level.
If the water pressure is less than
14.5 psi (1 bar), too little water may
flow into the wash cabinet.
To check the water level, open the
water valve completely and run the
RINSE & HOLD program once (with-
out dishes), to bring water into the
system.
Start the RINSE & HOLD program
again. After approximately 3
minutes, open the door and remove
the lower basket from the machine.The water level is correct when dimen-
sion “
X” is at least 1/8 (4 mm).
If it...

Increasing the water intake
time.
Position the program knob verti-
cally, then pull it off.Using a small screwdriver, turn the
adjusting slot on the right hand side
of the spindle 
carefully counterclock-
wise until it clicks into position.
= Counterclockwise turn 
(increases water intake to 
2 min.)
= Clockwise turn 
(factory setting - 1 min.)
Note:
If the water intake time has been in-
creased, the water hardness selector
should be set one number higher than
that stated in the “Water softener” chap-...

Problem solving guide
With the aid of the following notes,
minor problems can be easily cor-
rected. If you are unable to correct the
problem, please contact the Miele Ser-
vice Department.
Any work on the electrical compo-
nents of the appliance should only
be performed by a qualified and
trained person in accordance with
local and national regulations. Un-
authorized repairs could be dan-
gerous.
Problems and possible causes.
The dishwasher does not start.
– The door is not properly closed.
– The plug...

Accessories
Bottle holder.
(depending on model)
A bottle holder (for milk or baby bottles)
is available for use in the lower basket.
To achieve the proper cleaning results,
the bottle holder should only be placed
in the basket as shown in the illustra-
tion.Glass insert for the upper basket:
provides special support for long
stemmed glassware.
Decor panel kit (GDU):
to change an “i” model into a “u” model
dishwasher.
Side mount brackets:
For installing a dishwasher under Co-
rian
® or granite...

Installation instructions
45 

Contents
Dishwasher installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
1. Installing the steam deflector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48
2. Installing the dishwasher under the countertop. . . . . . . . . . . . . . . . . . . . . . . . .  48
3. Installing the control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  51
4. Aligning the control panel with the drawer...

Dishwasher installation
The “i” model dishwasher is designed
for installation under a continuous
countertop.
A panel can be custom made for instal-
lation on the front of the dishwasher, as-
suring a perfect match with the kitchen
cabinetry.
If a standard non-cabinet matching
dishwasher installation is desired, the
“i” model dishwasher can be converted
into a “U” model through the addition of
a GDU 60/60 decor kit. The decor kit is
supplied with separate installation in-
structions.
To ensure stability,...

1. Installing the steam deflector
– (if applicable).
A stainless steel plate is supplied to
protect the underside of the countertop
against steam rising from the dish-
washer when the door is opened. If the
countertop is made of Corian®, gra-
nite, marble or other solid, waterproof
material, the steam deflector should not
be used.
Squeeze a bead of sealant from the
supplied tube into the angle formed
by the curved edge 
b of the cover-
plate. 
Align the plate c with the lower front
edge of the countertop...

Install the slides.
Two slides are included and should be
installed on the feet of the dishwasher
before the machine is pushed under
the countertop. This will allow the ma-
chine to slide easier, protect the floor,
and allow adjustment of the rear level-
ing legs from the front of the machine.
Place the slides, with the ratchet at
the rear, onto the dishwasher legs.
Unscrew the legs to raise the ma-
chine to within 1/4 (5 mm) of the
underside of the countertop, and
check that the machine is level,...

Adjust the rear leveling legs to the re-
quired height.
To raise the machine - turn clockwise.
To lower the machine - turn counter-
clockwise.
Several turns may be needed to set the
correct height. A low speed electric or
cordless screwdriver can also be used.Adjust the front leveling legs by
pushing on the foot with a slotted
screwdriver.
Tipping the machine slightly, if
possible, will make adjusting the
front legs easier. Make sure the ma-
chine is level when adjustments are
complete.
The dishwasher...