Miele G 7893 Manual

Fault Possible cause Remedy
The cleaning result is
unsatisfactory.Baskets or inserts have
been incorrectly loaded or
overloaded.Rearrange the items.
Do not overload baskets or
inserts.
The programme selected
is not suitable for the
degree of soiling.Select a suitable
programme or change the
programme parameters.
The cleaning agent used is
not suitable for the degree
of soiling.Use a cleaning agent
suitable for machine
processing.
Soiling has been allowed
to dry onto the items for
too long.Items should...

Thermal cut-out
This machine has a resettable heater
limiter which will shut off the elements in
the event of over-heating. This could be
caused, for example, by large articles
covering the heating elements or if the
filters in the wash cabinet are blocked.
If the fault code:F01 - F03,F18,F19,
F27(water was not heated up in the
wash cabinet and the programme is
taking too long) shows in the display,
proceed as follows:
^Remove the cause of the fault.
^Remove the service panel.
^Press the reset button on...

Cleaning the drain pump and
non-return valve
If water has not been pumped away at
the end of a programme, the drain
pump or the non-return valve might be
blocked. They are easy to clean.
^Take the filter combination out of the
wash cabinet.
^Release the locking clamp.
^
Lift up the non-return valve and rinse
under running water.The drain pump is situated under the
non-return valve (see arrow).
^Before replacing the non-return
valve, check that the drain pump is
free of obstructions.
^Carefully replace...

Cleaning the filters in the water
inlet
Filters are incorporated in the screw
connection of the water inlet hose to
protect the water inlet valve. If these
filters get dirty they need to be cleaned,
otherwise insufficient water flows into
the wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must not be dipped in
water.To clean the filter
^Disconnect the machine from the
mains supply.
^Turn off the stopcock and unscrew
the water inlet hose.
^Clean the large...

In the event of any faults that you
cannot remedy yourself, please contact
your authorised Service Dealer or the
Miele Customer Contact Centre. See
back cover for contact details.
^When calling your Dealer or the Miele
Customer Contact Centre, please
quote the model and serial number of
your machine, both of which are
shown on the data plate (see
"Electrical connection").
^Please also quote any fault code.
Please note that telephone calls may
be monitored and recorded for
training purposes.
After...

Please refer to the installation
diagrams supplied with the
machine.
,Furniture and fittings installed
near the machine must be of a
commercial standard able to
withstand the effects of steam and
condensation.
The machine must be installed correctly
and levelled.
Any unevenness in the floor level can
be compensated for and the height of
the machine raised or lowered by
adjusting the front screw feet.
The machine can be installed in the
following ways:
– Free-standing.
– The machine can be installed next...

Level and secure the machine
To ensure stability, the machine must
first be aligned and then screwed to the
worktop.
^Open the door.
^Secure the machine to the front edge
of the worktop using screws through
the holes on the left and right hand
sides of the front trim.
^
Do not use silicone sealant to seal
the gaps between the machine and
any neighbouring units as this would
hinder ventilation to the circulation
pump.Cover plate (protects the worktop)
If required, a special cover plate can
be ordered from...

,All electrical work must be
carried out by a suitably qualified
and competent person in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
–Connection should be made via a
suitable isolator, with an on-off switch
which is easily accessible for
servicing and maintenance work
after the machine has been installed.
An electrical safety test must be
carried out after installation and after
any servicing work. When switched
off there must be an all-pole contact
gap of at...

Connection to the water inlet
,The water in the machine must
not be used as drinking water.
–The machine must be connected to
the water supply in strict accordance
with current local and national water
authority regulations (WRC in the
U.K.).
–If the iron content in the water is too
high, there is a risk of corrosion
occuring on items being processed
in the machine, as well as in the
machine itself.
If the chloride content of the water
exceeds 100mg/l, the risk of
corrosion to items being processed
in...

–Large surface area filters are
enclosed in the kit supplied with the
machine for installing between the
stopcock and the inlet hose (see
illustration in "Maintenance -
Cleaning the filters in the wash
cabinet'"). The large surface area
filter for AD water is made from
chrome nickel steel, and can be
recognised by the matt top surface.
,The inlet hoses mustnotbe
shortened or damaged in any way
(see illustration).
See also the installation diagram
supplied.AD water connection (pressurised)...