Miele G 5570 Operating Instructions

The Settings menu allows
you to change standard
settings
Opening the Settings menu
Press thebutton to turn the
dishwasher off, if it is still on.
Hold the program button down.
Turn the dishwasher on with the
button and hold the program button
down for a few seconds.
The first option of the Settings menu will
appear in the display and all the
indicator lights will come on.
Select the menu option you wish to
change.
The selected options are marked
with a check
.
Language
The display contents can be...

Water hardness
Your dishwasher is fitted with a water
softener which you need
to program to the water hardness level
in your area.
–The dishwasher must be correctly
programmed to match the hardness
of your water.
–Your local water authority will be able
to advise you of the exact water
hardness level in your area.
–In areas where the water hardness
fluctuates (e. g. 37 - 50 °d [39
-52 gr/gal]) always program the
machine to the higher value (in this
example 50 °d [52 gr/gal]).
A checkwill appear beside...

Rinse aid
For best results the rinse aid dosage
can be adjusted.
The dosage can be set between 0-6 ml.
The factory default dosage setting is
3 ml rinse aid.
The amount of rinse aid dispensed can
be more than the value set due to the
automatic adjustment of the Sensor
Wash program.
If spots appear on the dishes:
–Use a higher setting for rinse aid.
If smearing or streaking show:
– Use a lower setting for rinse aid.
Select the desired rinse aid amount
and confirm with the center button.
Buzzer
When the...

Optimize standby
A few minutes after the last key is
pressed or at the end of the program
the dishwasher will turn off to save
energy. The display and the indicators
are turned off and only theStart/Stop
indicator light flashes slowly.
If you do not turn the dishwasher off
after the program ends, it will turn
completely off after a few minutes in
Standby mode.
This function can also be turned off.
The display and the indicators stay on
and the dishwasher will turn off after
approx. 6 hours.
Select the...

Soak
You can use the Soak function in the
program selected for loosening very
stubborn food residues. It is not
available for every program.
If you are using powder dishwasher
detergent, add approx. 1 teaspoon
(5 g) to compartment I.
Select the desired setting and
confirm with the center button.
Once set, the function will remain active
for the programs for which it is
available, until the setting is changed.
Pre-rinse
You can use this function in the
selected program to remove easily
loosened food...

Filter check
This selection allows you to set the
number of cycles run before the filter
check message shows.
You can select between 30 and 60
cycles.
The Filter check message is set by
default to 50 cycles.
Select the desired interval and
confirm with the center button.
Showroom program
Only for showrooms.
The dishwasher has a demo program
for dealers showrooms.
–
Demo with wash sound:
The program activates the pumps to
demonstrate the wash sound.
Turning the demo mode on
Select the desired option.
...

Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
After the dishwasher was
turned on with the
button, the display stays
off and the Start/Stop
indicator does not flash.The machine is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker.
See the data plate for
minimum...

Faults in the water intake/water drain
Problem Possible fault Solution
One of the following
faults appears on the
display:Before fixing the fault:
–Press thebutton to turn
the dishwasher off.
	Open water supplyThe water supply valve
is closed.Open the water supply valve all
the way.
	Water intakeBefore fixing the fault:
–Press thebutton to turn
the dishwasher off.
Fault in the water
intake.–Open the water supply all
the way and restart the
program.
– Clean the water intake filter
(see Cleaning and...

General problems with the dishwasher
Problem Possible fault Solution
The indicators and the
display is dark. Only
the Start/Stop
indicator flashes
slowly.The display goes into
Standby mode to save
energyPress thebutton.
Standby is ended.
Detergent residue is left
in the dispenser at the
end of a program.The dispenser was
damp when detergent
was added.Dry the dispenser before
adding detergent.
The detergent
dispenser lid cannot be
closed properly.Detergent residue is
blocking the catch.Remove the...

Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinetThe spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinetItems are not secure in the
wash cabinet.Interrupt the program, and
rearrange loose pieces.
A foreign object has
become lodged in the
drain pump.Remove the foreign object
from the drain pump (see
Cleaning the drain pump
and non-return valve)
There is a knocking
noise...