Miele G 5570 Operating Instructions

							The Settings menu allows
you to change standard
settings
Opening the Settings menu
Press thebutton to turn the
dishwasher off, if it is still on.
Hold the program button down.
Turn the dishwasher on with the
button and hold the program button
down for a few seconds.
The first option of the Settings menu will
appear in the display and all the
indicator lights will come on.
Select the menu option you wish to
change.
The selected options are marked
with a check
.
Language
The display contents can be shown in
different languages.
The displayed language can be
changed in the
Language.
Select the desired language and
confirm with the center button.
The flag after the wordLanguage
serves as a guide when an
unfamiliar language has been
selected.
Select the menu option with a flag
until the
Languagesubmenu is
displayed.
Settings menu
41
 
						

							Water hardness
Your dishwasher is fitted with a water
softener which you need
to program to the water hardness level
in your area.
–The dishwasher must be correctly
programmed to match the hardness
of your water.
–Your local water authority will be able
to advise you of the exact water
hardness level in your area.
–In areas where the water hardness
fluctuates (e. g. 37 - 50 °d [39
-52 gr/gal]) always program the
machine to the higher value (in this
example 50 °d [52 gr/gal]).
A checkwill appear beside the
water hardness which has been set.
Select the hardness of your water
supply and confirm with the center
button.
°d gr/galValue to set
in the display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37-50
51-60
61-701
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
38
39-52
53-63
64-731
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37-50
51-60
61-70
Settings menu
42
 
						

							Rinse aid
For best results the rinse aid dosage
can be adjusted.
The dosage can be set between 0-6 ml.
The factory default dosage setting is
3 ml rinse aid.
The amount of rinse aid dispensed can
be more than the value set due to the
automatic adjustment of the Sensor
Wash program.
If spots appear on the dishes:
–Use a higher setting for rinse aid.
If smearing or streaking show:
– Use a lower setting for rinse aid.
Select the desired rinse aid amount
and confirm with the center button.
Buzzer
When the buzzer is activated, a tone
sounds at the end of a program and if a
fault occurs.
Buzzer at the end of a program
The buzzer at the end of a program
sounds four times in intervals with a
brief break in between. The buzzer
sounds if the dishwasher has not been
turned off.
The buzzer at the end of a program is
turned off by default.
Buzzer in case of a fault
In the event of a fault, the buzzer
sounds continuously.
The fault buzzer cannot be turned
off.
Buzzer volume
There are seven different volume
settings. If no volume level is selected,
the buzzer is deactivated.

Select the desired volume and
confirm with the center button.
Settings menu
43
 
						

							Optimize standby
A few minutes after the last key is
pressed or at the end of the program
the dishwasher will turn off to save
energy. The display and the indicators
are turned off and only theStart/Stop
indicator light flashes slowly.
If you do not turn the dishwasher off
after the program ends, it will turn
completely off after a few minutes in
Standby mode.
This function can also be turned off.
The display and the indicators stay on
and the dishwasher will turn off after
approx. 6 hours.
Select the desired setting and press
the center button.
If refill salt and/or rinse aid or a fault
are present in the display, the
dishwasher will go into Standby
mode.
The refill messages can be turned
off when you use a tab detergent
(see Before using for the first time).
Fault messages cannot be turned
off.
Deactivate indicators
If you consistently use Tab detergent
products in your dishwasher, you can
switch the Salt and Rinse Aid indicators
off if desired.
Select the desired setting and
confirm with the center button.
If you switch to using a detergent
that does not contain salt or rinse
aid, remember to replenish the salt
and rinse aid and turn the indicators
back on.
Settings menu
44
 
						

							Soak
You can use the Soak function in the
program selected for loosening very
stubborn food residues. It is not
available for every program.
If you are using powder dishwasher
detergent, add approx. 1 teaspoon
(5 g) to compartment I.
Select the desired setting and
confirm with the center button.
Once set, the function will remain active
for the programs for which it is
available, until the setting is changed.
Pre-rinse
You can use this function in the
selected program to remove easily
loosened food residues. It is not
available for every program.
Select the desired setting and
confirm with the center button.
Once set, the function will remain active
for the programs for which it is
available, until the setting is changed.
Extended drying
The fan runs longer at the end of a
program to improve the drying result.
This function is not available for every
program.
Select the desired setting and
confirm with the center button.
Once set, the function will remain active
for the programs for which it is
available, until the setting is changed.
Brightness
There are seven different display
brightness settings.
Select the desired brightness and
confirm with the center button.
Contrast
There are seven different display
contrast settings.
Select the desired contrast and
confirm with the center button.
Settings menu
45
 
						

							Filter check
This selection allows you to set the
number of cycles run before the filter
check message shows.
You can select between 30 and 60
cycles.
The Filter check message is set by
default to 50 cycles.
Select the desired interval and
confirm with the center button.
Showroom program
Only for showrooms.
The dishwasher has a demo program
for dealers showrooms.
–
Demo with wash sound:
The program activates the pumps to
demonstrate the wash sound.
Turning the demo mode on
Select the desired option.

Select the option
Onand confirm with
the center button.

Close the door.
Demo mode will begin.
Turning the demo mode off
Demo mode will switch off automatically
when it reaches the end of the cycle.
Factory default
If you have altered any settings from
the factory default, you can reset them
to the factory default settings.
Select
Resetand confirm with the
center button.
Leaving the Settings menu
UseCloseto leave the Settings menu.
Select
Closeand confirm with the
center button.
The display will then show the last
program selected and the indicator
light for the program selected will come
on.
Settings menu
46
 
						

							Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
After the dishwasher was
turned on with the
button, the display stays
off and the Start/Stop
indicator does not flash.The machine is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker.
See the data plate for
minimum amperage.
The dishwasher stops
during a program.The circuit breaker has
tripped.– Reset the circuit breaker
(see the data plate for
minimum amperage).
– If the circuit breaker
trips again. Contact
Miele.
One of the following
faults appears on the
display:Before fixing the fault:
– Press thebutton to
turn the dishwasher off.
Fault FXXThere may be a
technical fault.After a few seconds:
–
Turn the dishwasher on.
–
Select the desired
program.
–
Press the Start/Stop
button.
If the fault is indicated
again, a technical fault has
occurred.
–
Contact Miele.
WaterproofThe waterproof system
has activated.–
Turn off the water
supply.
–
Contact Miele.
Frequently Asked Questions
47
 
						

							Faults in the water intake/water drain
Problem Possible fault Solution
One of the following
faults appears on the
display:Before fixing the fault:
–Press thebutton to turn
the dishwasher off.
	Open water supplyThe water supply valve
is closed.Open the water supply valve all
the way.
	Water intakeBefore fixing the fault:
–Press thebutton to turn
the dishwasher off.
Fault in the water
intake.–Open the water supply all
the way and restart the
program.
– Clean the water intake filter
(see Cleaning and Care).
– The water pressure at the
water connection is less than
30kPa (0.3 bar/4.35 psi).
Consult a plumber.
DrainFault in the water drain.
There might be water in
the wash cabinet.– Clean the triple filter (see
Cleaning and care).
–
Clean the drain pump (see
Cleaning and Care).
–
Clean the non-return valve
(see Cleaning and Care).
–
Remove any kinks in the
drain hose.
Frequently Asked Questions
48
 
						

							General problems with the dishwasher
Problem Possible fault Solution
The indicators and the
display is dark. Only
the Start/Stop
indicator flashes
slowly.The display goes into
Standby mode to save
energyPress thebutton.
Standby is ended.
Detergent residue is left
in the dispenser at the
end of a program.The dispenser was
damp when detergent
was added.Dry the dispenser before
adding detergent.
The detergent
dispenser lid cannot be
closed properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a program has
finished.This is not a fault.
It is the normal
operating mode of the
drying system.The moisture will evaporate
after a short time.
Water remains in the
wash cabinet at the end
of a program.Before fixing the fault:
– Press thebutton to turn
the dishwasher off.
The triple filter in the
wash cabinet is
clogged.Clean the triple filter (see
Cleaning and care).
The drain pump or the
non-return valve may
be blocked.Clean the drain pump and
the non-return valve (see
Cleaning and care).
The drain hose is
kinked.Remove any kinks from the
drain hose.
Frequently Asked Questions
49
 
						

							Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinetThe spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinetItems are not secure in the
wash cabinet.Interrupt the program, and
rearrange loose pieces.
A foreign object has
become lodged in the
drain pump.Remove the foreign object
from the drain pump (see
Cleaning the drain pump
and non-return valve)
There is a knocking
noise in the water lineThis may be caused by
the installation or the
diameter of the pipe.This has no effect on the
dishwasher. If in doubt,
contact a plumber.
Frequently Asked Questions
50