Miele G 4220 Manual

At the end of a program
The program has ended if the time
display shows a0.
Now you can open the dishwasher and
unload the dishware.
At the end of a program:
Press thebutton to turn the
dishwasher off.
The dishwasher will continue to use
electricity until it is turned off with the
button.
If you would like to open the door at
the end of the program, then make
sure that you open the door fully.
Otherwise steam from the
dishwasher could damage the edge
of the counter top because the fan is
no longer...

Interrupting a program
A program will be interrupted as soon
as the door is opened.
When the door is closed again, the
program will continue from where it was
interrupted.
Water in the dishwasher is hot.
Risk of scalding!
Only open the door if absolutely
necessary and be very careful.
Before closing the door again, leave
it slightly ajar for approx.
20 seconds. This will allow the
temperature in the wash cabinet to
settle. Then push the door firmly
shut until it clicks into place.
Changing a program
Do...

Turbo
The Turbo function reduces the
program runtimes in programs where
the option is available.
Energy consumption will increase to
achieve optimum results.
Press thebutton to turn the
dishwasher on.
The Start/Stop indicator light flashes.
Select the desired program.
Press the Turbo button.
The Turbo indicator light comes on.
Now you can start a program.
Once selected, the function will remain
active for all programs until the setting
is changed.
Additional options
33 

Delay start
The start time of a program can be
delayed. The start time can be delayed
from 30 minutes to 24 hours. The delay
is set in 30 minute increments.
For a delay start time between 30
minutes and 9 hours 30 minutes, the
delay is set in 30 minute increments.
For a delay start time of 10 hours or
more, the delay is set in increments of
one hour.
When using the Delay start function,
make sure that the detergent
compartment is dry before adding
detergent. Wipe dry if necessary.
Otherwise the detergent...

The time will count down to the
program start: for more than 10 hours in
1 hour increments, for less than 10
hours in 1 minute increments.
When the set time is reached, the
selected program will start
automatically. The remaining runtime is
shown in the time display, the Delay
start indicator light goes out and the
Start/Stop indicator light comes on.
Delay start time shown in the time
display:
up to 59 minutes:
e.g. 30 minutes =30
1 hour to 9 hours 30 minutes:
e.g. 5 hours =5.00
more than 10 hours:
e.g....

Memory
The memory function allows you to save
the last selected program.
If you turn the dishwasher off and on
again after a program has finished or
open and close the door, the last
selected program is displayed instead
of the Economy program.
Press thebutton to turn the
dishwasher off.
Press and hold the Start/Stop button
andsimultaneouslyturn the
dishwasher on using thebutton.
Keep the Start/Stop button pressed
for at least four seconds until the
Start/Stop indicator light comes on.
If it does not...

Optimize Standby
A few minutes after the last button is
pressed or a few minutes after the end
of the program the dishwasher will
switch to Standby mode to save
energy. The time display and the
indicator lights are turned off and only
the Start/Stop indicator light flashes
slowly.
If the dishwasher is not turned off or
opened after the program ends, after a
few minutes in Standby mode it will turn
off completely.
You can also deactivate the Optimize
Standby function. The display and the
indicator lights...

Factory defaults
If you have changed any settings, you
can reset them to the factory defaults.
Press thebutton to turn the
dishwasher off.
Press and hold the Start/Stop button
andsimultaneouslyturn the
dishwasher on using thebutton.
Keep the Start/Stop button pressed
for at least four seconds until the
Start/Stop indicator light comes on.
If it does not come on, start over.
Press the Delay start button 12 times.
The Delay start indicator light shows 1
long flash and 2 short flashes in
intervals.The...

Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
After turning on the
dishwasher with the
button, the Start/Stop
indicator light does not
flash.The dishwasher is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker
(see data plate for the
correct fuse rating).
The dishwasher...

Faults in the water intake or water drain
Problem Possible fault Solution
The Intake/Drain
indicator light
alternates between
flashing and
remaining steady.The water supply is
closed.Open the water supply all the
way.
The dishwasher
stops running.
The Intake/Drain
indicator light
flashes.
The time display
shows fault FXX.Before fixing the fault:
–Press thebutton to turn the
dishwasher off.
Fault F12/F13:
Water intake fault.–Open the water supply all the
way.
– Clean the screen in the water
intake (see...