Miele G 4220 Manual

							At the end of a program
The program has ended if the time
display shows a0.
Now you can open the dishwasher and
unload the dishware.
At the end of a program:
Press thebutton to turn the
dishwasher off.
The dishwasher will continue to use
electricity until it is turned off with the
button.
If you would like to open the door at
the end of the program, then make
sure that you open the door fully.
Otherwise steam from the
dishwasher could damage the edge
of the counter top because the fan is
no longer running.
Unload the dishwasher.
Dishes tend to break and chip more
easily when they are hot.
Allow the dishes to cool until they are
comfortable enough to handle before
unloading them.The dishes will cool much faster if you
open the door when the program has
ended.
Unload the lower basket first, then
the upper basket and then the cutlery
tray (depending on the model).
This will prevent water from the upper
basket and cutlery tray from dripping
onto dishes in the lower basket.
Preparing your appliance for
an extended vacation
If you elect to turn off the water to your
home for an extended period of time,
please note that this may not be
enough to reduce the risk of a leak.
To be completely safe, you must
turn off the water supply to each
individual appliance. This means
under the sink for a dishwasher, at
the laundry bib for your washer, etc.
Use
31 
						

							Interrupting a program
A program will be interrupted as soon
as the door is opened.
When the door is closed again, the
program will continue from where it was
interrupted.
Water in the dishwasher is hot.
Risk of scalding!
Only open the door if absolutely
necessary and be very careful.
Before closing the door again, leave
it slightly ajar for approx.
20 seconds. This will allow the
temperature in the wash cabinet to
settle. Then push the door firmly
shut until it clicks into place.
Changing a program
Do not change the program if the
detergent dispenser flap is already
open.
If a program has already started and
you wish to change it:
Press the Start/Stop button for at
least one second.
The program will be canceled.
Select and start the desired program.
Use
32 
						

							Turbo
The Turbo function reduces the
program runtimes in programs where
the option is available.
Energy consumption will increase to
achieve optimum results.
Press thebutton to turn the
dishwasher on.
The Start/Stop indicator light flashes.
Select the desired program.
Press the Turbo button.
The Turbo indicator light comes on.
Now you can start a program.
Once selected, the function will remain
active for all programs until the setting
is changed.
Additional options
33 
						

							Delay start
The start time of a program can be
delayed. The start time can be delayed
from 30 minutes to 24 hours. The delay
is set in 30 minute increments.
For a delay start time between 30
minutes and 9 hours 30 minutes, the
delay is set in 30 minute increments.
For a delay start time of 10 hours or
more, the delay is set in increments of
one hour.
When using the Delay start function,
make sure that the detergent
compartment is dry before adding
detergent. Wipe dry if necessary.
Otherwise the detergent could
clump and not be rinsed out
completely.
Do not use liquid detergent. Liquid
detergent could leak out of the
compartment.Press thebutton to turn the
dishwasher on.
The Start/Stop indicator light flashes.
Use the Program button to select the
desired program.
Press the Delay start button.
The last Delay start time will appear in
the time display. The Delay start
indicator light comes on.
Set the desired Delay start time using
the Delay start button.
If you keep the button pressed, the time
will increase automatically to24^.To
start at 30 minutes again, press the
Delay start button twice.
Press the Start/Stop button.
The Start/Stop indicator light comes on.
Additional options
34 
						

							The time will count down to the
program start: for more than 10 hours in
1 hour increments, for less than 10
hours in 1 minute increments.
When the set time is reached, the
selected program will start
automatically. The remaining runtime is
shown in the time display, the Delay
start indicator light goes out and the
Start/Stop indicator light comes on.
Delay start time shown in the time
display:
up to 59 minutes:
e.g. 30 minutes =30
1 hour to 9 hours 30 minutes:
e.g. 5 hours =5.00
more than 10 hours:
e.g. 15 hours =15^
To prevent children coming into
contact with detergent:
Fill the detergent dispenserjust
before starting the program, i.e.
just before pressing the Start/Stop
button, and lock the door with the
child safety lock.Starting a program before Delay start
has elapsed:
A program can be started before the
Delay start time has elapsed. Do the
following:
Press the Start/Stop button for at
least one second.
The Delay start indicator light goes out
and the Start/Stop indicator light
flashes.
Press the Start/Stop button again.
The program starts. The Start/Stop
indicator light comes on.
Additional options
35 
						

							Memory
The memory function allows you to save
the last selected program.
If you turn the dishwasher off and on
again after a program has finished or
open and close the door, the last
selected program is displayed instead
of the Economy program.
Press thebutton to turn the
dishwasher off.
Press and hold the Start/Stop button
andsimultaneouslyturn the
dishwasher on using thebutton.
Keep the Start/Stop button pressed
for at least four seconds until the
Start/Stop indicator light comes on.
If it does not come on, start over.
Press the Delay start button six times.
The Delay start indicator light shows 6
short flashes in intervals.The flashing in the time display shows
whether Memory is turned on.
–p1: Memory is on.
–p0: Memory is off.
Press the Start/Stop button if you
wish to change the setting.
The setting is immediately saved.
Press thebutton to turn the
dishwasher off.
Additional options
36 
						

							Optimize Standby
A few minutes after the last button is
pressed or a few minutes after the end
of the program the dishwasher will
switch to Standby mode to save
energy. The time display and the
indicator lights are turned off and only
the Start/Stop indicator light flashes
slowly.
If the dishwasher is not turned off or
opened after the program ends, after a
few minutes in Standby mode it will turn
off completely.
You can also deactivate the Optimize
Standby function. The display and the
indicator lights do not go out, and the
dishwasher turns off 6 hours after the
end of the program.
This results in higher energy
consumption.
If refill rinse aid or a fault is
displayed while a program is
running, the dishwasher will not
switch to Standby mode.Press thebutton to turn the
dishwasher off.
Press and hold the Start/Stop button
andsimultaneouslyturn the
dishwasher on using thebutton.
Keep the Start/Stop button pressed
for at least four seconds until the
Start/Stop indicator light comes on.
If it does not come on, start over.
Press the Delay start button eight
times.
The Delay start indicator light shows 8
short flashes in intervals.
The flashing in the time display shows
whether Optimize Standby is turned on.
–p1: Optimize Standby is on.
–p0: Optimize Standby is off.
Press the Start/Stop button if you
wish to change the setting.
The setting is immediately saved.

Press thebutton to turn the
dishwasher off.
Additional options
37 
						

							Factory defaults
If you have changed any settings, you
can reset them to the factory defaults.
Press thebutton to turn the
dishwasher off.
Press and hold the Start/Stop button
andsimultaneouslyturn the
dishwasher on using thebutton.
Keep the Start/Stop button pressed
for at least four seconds until the
Start/Stop indicator light comes on.
If it does not come on, start over.
Press the Delay start button 12 times.
The Delay start indicator light shows 1
long flash and 2 short flashes in
intervals.The flashing in the time display shows
whether a setting is different from the
default setting.
–p1: all values are set to the default
settings
–p0: at least one setting has been
changed.
Press the Start/Stop button to reset
the dishwasher to the default
settings.
The setting is immediately saved.
Press thebutton to turn the
dishwasher off.
Additional options
38 
						

							Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
After turning on the
dishwasher with the
button, the Start/Stop
indicator light does not
flash.The dishwasher is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker
(see data plate for the
correct fuse rating).
The dishwasher stops
during a program.The circuit breaker has
tripped.– Reset the circuit
breaker (see data plate
for the correct fuse
rating).
– If the circuit breaker
trips again, contact
Miele.
The indicators
Intake/Drain and Rinse
aid flash simultaneously.
The time display shows
fault FXX.There may be a technical
fault.– Press thebutton to
turn the dishwasher off.
After a few seconds:
–
Turn the dishwasher
on.
–
Use the Program
button to select the
desired program.
–
Press the Start/Stop
button.
If the indicator lights flash
again, there is a technical
fault.
–
Contact Miele.
In addition, the drain
pump may run even
when the door is open.Fault F70:
The waterproof system
reports a fault.–
Close the water tap.
–
Contact Miele .
Frequently asked questions
39 
						

							Faults in the water intake or water drain
Problem Possible fault Solution
The Intake/Drain
indicator light
alternates between
flashing and
remaining steady.The water supply is
closed.Open the water supply all the
way.
The dishwasher
stops running.
The Intake/Drain
indicator light
flashes.
The time display
shows fault FXX.Before fixing the fault:
–Press thebutton to turn the
dishwasher off.
Fault F12/F13:
Water intake fault.–Open the water supply all the
way.
– Clean the screen in the water
intake (see User maintenance
instructions).
– The water pressure at the
water connection is less than
4.35 psi.
Consult a plumber.
Fault F11:
Water drainage fault.
There might be water in
the wash cabinet.– Clean the triple filter (see
Cleaning and care).
– Clean the drain pump (see
User maintenance
instructions).
–
Clean the non-return valve
(see User maintenance
instructions).
–
Remove any kinks or high
loops in the drain hose.
Frequently asked questions
40