Miele G 4220 Manual

Cleaning the spray arms
Sometimes particles of food get stuck
in the spray arm jets. The spray arms
should be inspected and cleaned every
4 - 6 months.
Turn off the dishwasher before
cleaning.
Removing the spray arms
Remove the cutlery tray (if present).
Push theupperspray arm up to
engage the inner ratchet and
unscrew the spray arm.

Lift up themiddlespray arm,,to
engage the ratchet and unscrew the
spray arm,.

Remove the lower basket.Pull thelowerspray arm firmly
upwards to remove.

Use a...

Cleaning the drain pump and
non-return valve
If the dishwasher is not completely
drained at the end of a program, the
drain pump or non-return valve may be
blocked.
Turn off the dishwasher and pull the
plug.
Remove the triple filter (see Triple
filter system).
Use a cup or bowl to scoop water out
of the wash cabinet.

Tilt the locking clamp to the side.

Pull out the non-return valveand
rinse it under running water.

Remove all foreign objects from the
non-return valve.The drain pump is beneath...

Installation Instructions
Please refer to the Installation Diagram supplied with these instructions.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information. 

Installation, repairs and other
work by unqualified persons could
be dangerous.
Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.
The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.
A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician.
GROUNDING INSTRUCTIONS...

Hardwired electrical connection
It is possible to hardwire this appliance
to an existing power cable.
CAUTION: Before servicing,
disconnect the power supply by
either removing the fuse, shutting off
the power main or manually
tripping the circuit breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous and
the manufacturer cannot be held
responsible....

Connection to the water
supply
Installation, repairs and other
work by unqualified persons could
be dangerous.
Do not drink water from the
dishwasher!
–The dishwasher can heat its own
water to the temperature required by
the wash program. This allows for
connection of the machine to either a
hot (max. 140°F / 60°C) or cold water
source.
For lowest energy consumption and
fastest possible wash times connect
the dishwasher to a hot water
source. All programs use hot water in
the rinse cycles.
– The inlet...

Drainage
–The machine comes equipped with a
built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.
–The dishwasher is equipped with a
5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8 (22 mm).
–Drain hose extensions and adapters
can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39
(1 m).
– Use the clamp provided to attach the
hose to the dishwashers P trap or
disposal connection (see the...

General requirements for measuring noise
The dishwasher must be loaded with16 place settingsand theNormalprogram
must be used.
Installation requirements for measuring noise
The dishwasher must be installed as follows:.

Install the dishwasher into an appropriate housing unit.

Secure the front panel.
Noise measurement
58 

Push the insulation mat supplied (depending on model) under the plinth until it
is up against the appliance feet.
Attach the toe-kick so that it is flush with the door front.
Noise measurement
59 

Alteration rights reserved / 0213
G4220/G4225 /
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.M.-Nr. 09 510 191 / 00