Miele G 2872 Operating Instructions

To clean the underside of the filter the
flap must be opened.
	Push the clips togetherand open
the flap.
	Rinse under running water.
	Close the flap so that the clip
engages.	Return the filter so it lies flat in the
base of the wash cabinet.
	Lock the filter by turning the handle
clockwise.
The triple filter system must be
inserted and locked. Large particles
could get in the circulation system
and cause blockage.
Cleaning and Care
71
 

Cleaning the spray arms
Sometimes particles of food get stuck
in the spray arm jets. The spray arms
should be inspected and cleaned every
4 - 6 months.
	Turn off the dishwasher before
cleaning.
Removing the spray arms
	Remove the cutlery tray (if present).
	Push theupperspray arm up to
engage the inner ratchet and
unscrew the spray arm.
	
Lift up themiddlespray arm,,to
engage the ratchet and unscrew the
spray arm,.
	
Remove the lower basket.	Pull thelowerspray arm firmly
upwards to remove.
	
Use a...

Cleaning the water inlet filter
A filter is incorporated into the intake
hose attached to the dishwasher’s shut
off valve. If your water is hard or the
pipes contain sediment, this filter may
clog and prevent enough water from
entering the wash cabinet.
The plastic housing of the water
connection contains electrical
wiring.
Do not cut the intake hose or
submerge it in liquid.
Installing an in-line water filter
If your water contains a large number of
insoluble substances, a filter between
the water...

Cleaning the drain pump and
non-return valve
If the dishwasher is not completely
drained at the end of a program, the
drain pump or non-return valve may be
blocked.
	Turn off the dishwasher and pull the
plug.
	Remove the triple filter (see Triple
filter system).
	Use a cup or bowl to scoop water out
of the wash cabinet.
	
Tilt the locking clamp to the side.
	
Pull out the non-return valveand
rinse it under running water.
	
Remove all foreign objects from the
non-return valve.The drain pump is beneath...

Installation Instructions
Please refer to the Installation Diagram supplied with these instructions.
To comply with IEC sound testing protocols, please contact Miele for additional
instructions.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
 

Installation, repairs and other
work by unqualified persons could
be dangerous.
Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.
The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.
A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician.
GROUNDING INSTRUCTIONS...

Waterproof system
All Miele dishwashers have a safety valve
located on the incoming water line and a
sealed underside with a water sensor.
If a fault occurs, the water intake is
stopped and the drain pump is activated.
Connection to the water supply
Do not drink water from the
dishwasher!
– The dishwasher can heat its own water
to the temperature required by the
wash program. This allows for
connection of the machine to either a
hot or cold water source. For lowest
energy consumption connect the...

Drainage
–The machine comes equipped with a
built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.
–The dishwasher is equipped with a
5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8 (22 mm).
–Drain hose extensions and adapters
can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39
(1 m).
– If the hose is to be directly fitted to
the drainage outlet on site, use the
supplied hose clip (see...

79
 

Alteration rights reserved / 1711
G 2872
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.M.-Nr. 07 724 170 / 05