Miele G 2872 Operating Instructions

Mieles RemoteVision Wi-Fi technology
creates a virtual link between your
appliance and our monitoring center. If
a fault occurs, Mieles client service
center will be notified and contact you,
or another trusted individual identified
on your call roster, in order to gain
access to your appliance to fix the
problem.
For information on set-up and
installation of the RemoteVision module,
see the separate RemoteVision
installation manual.Be sure your wireless system meets the
following requirements
–A...

With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Issue Possible fault Solution
The program does not
start.The door is not properly
closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse has tripped. Reset the circuit...

Issue Possible fault Solution
The optical interface
flashes fast, the buzzer
sounds or the display
shows the fault:
A technical problem
occurred. Turn the
machine off, close the
water faucet and call
Technical Service.There may be a
technical fault.–Turn the dishwasher off by
touching thecontrol.
After a few seconds:
–Turn the dishwasher on.
–Select the desired
program.
–Close the door.
If the problem persists,
contact Technical Service.
Fault Waterproof F70The waterproof system
has activated.– Turn off...

Problems water intake/drain
Issue Possible fault Solution
The optical interface
flashes fast, the buzzer
sounds and the display
shows the fault:
No water intakeThe water supply is
closed.Open the water supply all
the way.
Fault water intake FXXBefore fixing the fault:
–Turn the dishwasher off
.
Fault F12/F13:
Fault in the water intake.–Open the water supply all
the way.
– Check and clean the
water intake filter, see
User Maintenance
Instructions.
– The water pressure at the
water connection is lower...

Issue Possible fault Solution
The optical interface
flashes fast.
The program Energy
Saver displays the
fault:
Water intake temp. too
low
The intake water does
not have a minimum
temperature of 115°F
(45°C). See Plumbing -
Connection to the water
supply.–Restart the program.
–If the fault is displayed
again, use a different
program.
The optical interface
flashes fast, the
buzzer sounds and the
display shows the
fault:
Drain fault F11
Before fixing the fault:
–Turn the dishwasher off.
Fault F11:
Fault in...

General problems with the dishwasher
Issue Possible fault Solution
The display turns off.The dishwasher has
gone into Standby
mode to save energy.Touch any control.
The display turns on again.
The display shows the
following:
Middle spray arm
blocked
or
Lower spray arm blocked
The middle or lower
spray arm is blocked by
dishware.Open the dishwasher door
and rearrange items blocking
the spray arms.
The spray arm jets of
the middle or lower
spray arm are clogged.–Turn the dishwasher off.
Then:
–Clean the...

Issue Possible fault Solution
Detergent is left in the
dispenser at the end
of a program.The dispenser was damp
when detergent was
added.Dry the dispenser before
adding detergent.
The detergent lid
cannot be closed
properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a program
has finished.This is not a fault! It is the
normal operating mode of
the drying system.The moisture will evaporate
after a short time.
Water remains in the
wash...

Sounds
Issue Possible fault Solution
There is a knocking
noise in the wash
cabinet.The spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinet.Items are not secure in the
wash cabinet.Interrupt the program and
rearrange loose pieces.
There is a knocking
noise in the water
pipes.This may be caused by
the installation or the
diameter of the pipe.This has no effect on the
dishwasher. If in doubt
contact a...

Poor cleaning results
Issue Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program, see Program
Guide.
Stubborn but normal soiling
(e.g. coffee, tea).Use the function Adjust
Sensor Wash. See
Settings- Adjust Sensor
Wash.
Not enough detergent was
dispensed.Use more detergent, see
Adding detergent.
The spray arms are blocked. Turn the spray arm and
rearrange the dishes if...

Issue Possible fault Solution
Dishes are not dry,
glasses and cutlery
are spotted.The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling, see Before using
for the first time.
Dishes were taken out too
soon.Leave dishes in longer, see
Use.
A Tab product was used.
These products have a low
drying effect.Set the Detergent setting for
a normal (powder or gel)
detergent and add rinse aid.
The Tab...