Miele G 1872 Operating Instructions

^Confirm the start time withOK.
The display will change to show the programme menu.
^Select
Start.
^Close the door.
When the set time is reached, the programme selected will
begin automatically.
Thedindicator light will go out.
Starting a programme before the start time has been reached:
You can start a programme before the set start time has been
reached. Proceed as follows:
^Open the door.
^Select
Canceland confirm withOK.
Thedindicator light will go out.
Sensor wash12:00
Programme finishedMain menu}...

Check your dishwasher regularly
(approx. every 4 - 6 months). This
way faults and problems can be
avoided.
*In the UK, Miele branded cleaning
and conditioning products as well as
a microfibre E-cloth which is suitable
for cleaning surfaces such as
stainless steel, glass, plastic and
chrome without the use of chemicals
are available from the Miele Spare
Parts Department or via the internet
on www.miele.co.uk.
Cleaning the wash cabinet
The wash cabinet is largely
self-cleaning, provided that the correct...

Cleaning the control panel
,Do not use abrasive cleaning
agents, glass cleaning agents or
all-purpose cleaners. Because of
their chemical composition, they
could cause serious damage to
surfaces.
^This shouldonlybe wiped with a
damp cloth.
Cleaning the door front
,Do not use any cleaning agents
containing ammonia or thinners.
These would damage the surface
structure.
^Clean the front using a Miele E-Cloth*
or with a suitable cleaning agent for
the type of material the front is made
of. Follow the...

Checking the filters in the
wash cabinet
The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it
accessing the circulation system and
re-entering the cabinet through the
spray arms.
,This dishwasher must not be
used without all the filters in place.
Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.
The message
Check filterswill appear
in the...

To clean the inside of the filter, the flap
must be opened:
^Press catchesatogether in the
direction of the arrows  as shown,
and open the filterb.
^Rinse all the filters under running
water.
^Then close the flap so that the catch
engages.^Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
^Then turn the handle clockwise to
lock the filter combination in place.
,Take care when you are fitting
the filter combination that it is
secured in position correctly.
Otherwise...

Cleaning the spray arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected
and cleaned regularly (approx. every
4 - 6 months).
^Switch the dishwasher off.
Remove the spray arms as follows:
^Take out the cutlery tray (if your
dishwasher is fitted with one).
^Push thetopspray arm upwards to
engage the inner ratchet. Then
unscrew the spray arm.
^
Push themiddlespray arms upwards
ato engage the ratchet. Then
unscrew the spray armb.^Remove the...

With the aid of the following guide, minor problems can be easily corrected
without calling in a Miele service technician, saving you both time and money.
,Repairs should only be carried out by a suitably qualified and trained
person in strict accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage to the
appliance.
Technical problems
Problem Possible cause Remedy
The dishwasher does
not start.The door is not properly...

Problem Possible cause Remedy
The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
One of the following
messages appears in
the display:
Technical fault! Switch the
appliance off, turn off the
water supply and call the
Service Department.There may be a
technical fault.–Switch the dishwasher off
with the Off buttono.
After a few seconds:
–Switch the dishwasher on.
–Select the programme you
want.
–Close the door.
If the fault message appears
again, there is a technical
fault.
–Call the...

The dishwasher does not fill/drain
Problem Possible cause Remedy
The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
One of the following
messages appears in
the display:
Water inlet faultThe stopcock is closed. Open the stopcock fully.
Water inlet fault FXXBefore rectifying the problem
you must:
–Switch the dishwasher off
with the Off buttono.
Fault F12/F13:
Water intake is
restricted.–Open the stopcock fully.
–Check the water inlet filter
and clean it if necessary
(see...

Problem Possible cause Remedy
The In-operation
indicator is flashing
quickly. In the
"Without heater"
programme the
following message
appears:
Water intake temp. too
low
The intake water has
not reached the
required temperature of
45°C (see Connection
to the water supply).–Start the programme again.
–If the fault message
appears again, select a
different programme.
The In-operation
indicator is flashing
quickly.
The buzzer is
sounding.
The following
message appears in
the display:
Drain fault...