Miele F 1471 Vi Operating And Installation Instructions

^Insert the cover strip into the space
between the appliance and the side
panel.
For side-by-side combinations, the
cover strips (on both sides of the
appliance) are applied to the
outermost spaces only.
^
Attach the light switch cover.
Attaching the toe-kick panel
The maximum height of the toe-kick
panel is 4 from the top of the floor.
Do not cover the ventilation slits in
the base panel. Risk of damage to
the appliance.
^If required, cut the toe-kick panel to
the required length and height.
^
Attach...

Mounting the air separator
The air separator on the inside of the
freezer door keeps the supply and
exhaust air separate. This prevents
warm exhaust air from flowing into the
machine, optimizing the energy
performance of the unit.
^If necessary, shorten the three parts
of the air separator.
^Insert the foam pieces back into the
sides.^Open the freezer door.
^Wedge the air separator at the
bottom of the freezer door, so it
connects in place.
Installing the appliance
72
 

Aligning the Ice/Water
Dispenser
If necessary the depth of the Ice/Water
dispenser can be aligned from inside
the custom door cut-out. This allows the
dispenser to be aligned with the
custom door to achieve the best
possible appearance.
^Press the dispenser back and pull
downwards to remove.^Remove the cover and the plastic
grill.
^
Remove the screw from the rear
casing, then lift the tab on the drip
tray up and off.
Installing the appliance
73
 

^Pull the rear cover forward and out.
^
To remove the drip tray, begin by
carefully unclipping the water
sensors, then bend them gently
upward.
Once the drip tray has been removed,
the four aligners can be accessed to
adjust the Ice/Water Dispenser to your
liking.^Loosen the screws of the four
clamps.
^Insert a screwdriver into one of the
four slots and push sideways until the
dispenser is aligned with the custom
door (the gray arrow will adjust to the
rear; the black arrow will adjust front)....

Attaching the frame and the
shelf
For3/4 (19 mm) thick custom doors:
^Slide the cover frame onto the
Ice/Water Dispenser and press until it
is flush with the door surface (be sure
the word TOP on the cover frame is
upward).
For 1
1/2 / (38 mm) thick custom doors:
^
Press the extension frame onto the
cover frame.
^
Slide the cover frame onto the
dispenser an press until the it is flush
with the door surface (be sure the
word TOP on the cover frame is
upward).
^
Insert the cover frame.
Installing the...

All plumbing work should be carried
out by a suitably qualified and
competent person, in accordance
with all applicable local and national
regulations.
The manufacturer is not liable for
damage to property due to an
incorrect installation or water
connection.
The water quality must conform to
country requirements for drinking
water.
– The appliance is only suitable for
connection to the cold water supply.
– The water pressure must be between
25 and 120 psi (1.72-8.25 bar).
– A separate shut-off valve...

Preparing the water connection
The connection to the household
water supply must be installed
before the appliance is installed.
^Turn off the main water valve to prevent
damage caused by leaking water.
^Attach the connecting pipe to the
shut-off valve, according to the
instructions supplied by the
manufacturer of the ice cube maker
installation kit.
^Install the connecting pipe. Always
observe the indicated clearance
dimensions to prevent damage to the
connecting pipe when pushing in the...

Connecting the water supply
When connecting the water pipe to
the solenoid valve of the appliance,
follow the instructions supplied by
the manufacturer of the ice cube
maker installation kit.
When bending the water pipe, be sure
not to kink it, otherwise there is a risk of
leaks and water damage.
Use bending aids.
^
Remove the cap from the appliance
connection,1.
^
Bend the water pipe to suit the
location of the connection on the
appliance,2.^Push the union nut and seal onto the
water pipe.
^Push the end...

,Avoid the risk of electrical
shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation,...

The Miele RemoteVision system is
designed to send messages directly to
Miele and/or your PC.
For information on set-up and
installation of the RemoteVision module
see the Installation section of this
manual.Be sure your wireless system meets the
following requirements
–Windows XP
®or newer operating
system, Mac®OS X 10.3 or higher
–Cable or DSL modem
–Microsoft
®Internet Explorer 6 or
higher, Safari 2.0 or higher, Firefox
1.5 or higher
* Please note that each wireless router
manufacturer supplies their...