Miele F 1471 Vi Operating And Installation Instructions

Have the appliance installed by a
qualified technician, according to
the enclosed installation instructions.
The manufacturer is not liable for
damage to property due to an
incorrect installation or water
connection.
WARNING
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.
Empty weight of your machine:
F 1471 Vi..........309lbs(140 kg)
Installation site
The...

Base
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor
must meet the following requirements:
F 1471 Vi..........505lbs(229 kg)
To ensure that the appliance is installed
securely and functions properly, the
base must be flat, level and made of a
hard, rigid material.
If in doubt, contact Miele.
Furniture/fixtures
The new appliance will be mounted
securely to adjacent and overhead
furniture/fixtures.
For this reason it is essential that all
attachable furniture/fixtures are...

Custom door panels
This appliance is compatible with all
styles and designs of kitchen cabinetry.
The total weight of the decorative
panel(s) must not exceed the following:
F 18X1 Vi...........134lbs(61kg)
Installation options
There are many different installation
options. These are limited only by the
design of the kitchen.
The door hinge cannot be
exchanged.
Single column
The appliance can be installed at any
preferred location in the kitchen.
However, be sure the door will open
and close properly in...

. . . with partition
The minimum thickness of the partition
is
5/8 (16 mm).
If there is a partition between the
adjacent appliances, then each
appliance is to be individually installed
within its own niche.A heating mat must only be installed if
the partition wall is less than 6
(160 mm) wide.
For instructions on how to install the
heating mat please refer to the
instructions included in the Merging
Kit.
The Merging Kit can be obtained
from Miele.
Side panels
If one side of the appliance is visible, a...

Niche dimensions
Niche width (A)
F 1471 Vi 18 (457 mm)
Dimensions
55
 

1. Power supply
2. Water connection
A
F 1471 Vi 9 (229 mm)
Door dimensions (open min. 115°)
AB
F 1471 Vi20
11/16 (525 mm) 93/16 (234 mm)
Dimensions
56
 

Dimensions
57
 

Before you begin
Read these instructions completely
and carefully.
Have the appliance installed by a
qualified technician, according to
the enclosed installation instructions.
To reduce the risk of injury or
damage to the product, two people
should be used for installation.
These installation instructions are
intended for use by qualified installers.
In addition to these instructions, the
appliance must be installed in
accordance with all local codes, or in
the absence of a local code.
– In the USA, in...

Check the installation niche
To ensure a safe, trouble-free
installation and the best possible
cosmetic result, check to be sure
that the installation space complies
with the installation requirements.
^Check the base (see Installation).
^Check the dimensions of the cavity.
^Check that the cavity is square.
^Check the location of the power
outlet.
^Check the location of the water
connection (see Plumbing).
^Check that all furniture parts in the
vicinity of the appliance are securely
connected to the...

^Loosen the bracket that holds the
appliance to the pallet.
,Caution! The appliance is no
longer secured and may be
unstable.
^From the rear of the appliance
carefully lift it from the pallet.
Once the appliance is on the ground it
can be wheeled around.
RemoteVision module
installation
Always disconnect the appliance
from the power supply when
performing installation, maintenance
or service work.
Install the RemoteVision module
before placing the appliance in its
installation niche.
Once connected the...