Miele Cs12121 Manual

Safety distances41Safety distances to the sidesand back of the hobThe CombiSet may be installed with awall at the rear and a tall unit or wall toone side (right or left) (see illustrations).0011 Minimum distance between the backof the worktop cut-out and the rearedge of the worktop:50 mm00120013 Minimum distance between theworktop cut-out and a tall unit or wall tothe right or left of it:
40 mmCS 1212 / CS 1212-1CS 1221 / CS 1221-1CS 1234 / CS 1234-1CS 1223CS 1222
50 mmCS 1112 CS 1122 CS 1134 CS 1326 CS...

Safety distances42Minimum safety distances un-derneath the hobTo ensure sufficient ventilation to thehob, a certain gap must be left betweenthe underside of the hob and any oven,interim shelf or drawer.The minimum gap between the under-side of the hob and
–the top of an oven is 15 mm.–the top of an interim shelf is 15 mm.–the base of a drawer is 75 mm.Interim shelfIt is not necessary to fit an interim shelfunderneath the hob but one may be fit-ted if you wish.Leave a gap of 10 mm at the back ofthe shelf...

Safety distances43Safety distance when installing the appliance near a wall withadditional niche claddingA minimum safety distance must be maintained between the worktop cut-out andany niche cladding to protect it from heat damage.If the niche cladding is made from a combustible material (e.g. wood) a minimumsafety distance 0014 of 50 mm must be maintained between the cut-out and thecladding.If the niche cladding is made from a non-combustible material (e.g. metal, naturalstone, ceramic tiles) the...

Installation notes44Seal between the CombiSetand the worktopDo not use sealant between theCombiSet and the worktop. Thiscould result in damage to theCombiSet or the worktop if theCombiSet ever needs to be removedfor servicing.The sealing strip under the edge ofthe top part of the applianceprovides a sufficient seal for theworktop.
Tiled worktop
Grout lines 0011 and the hatched area un-derneath the CombiSet frame must besmooth and even. If they are not theCombiSet will not sit flush with theworktop and...

Building-in dimensions45CS 1212-10001Spring clamps0002Front0003Casing depth0004Casing depth including mains connection box with mains connection cable, L =2000 mm  

Building-in dimensions46CS 1221-1 / CS 12220001Spring clamps0002Front0003Casing depth0004Casing depth including mains connection box with mains connection cable, L =2000 mm  

Building-in several CombiSets47Example: 3 CombiSets0001Spring clamps0002Spacer bars0003Gaps between spacer bars and worktop0004Cover strips0005CombiSet width minus 8 mm0006CombiSet width0007CombiSet width minus 8 mm0008Worktop cut-out  

Building-in several CombiSets48Calculating the worktop cut-outThe frames of the CombiSets overlap the worktop at the outside right and left by8 mm on each side.000EAdd up the widths of the CombiSets and subtract 16 mm from this figure.
Example:288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm
The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see"Building-in dimensions").
Spacer barsWhen building-in several CombiSets a spacer bar must be fitted between eachCombiSet. The position...

Installation49Preparing the worktop000EMake the worktop cut-out as shownin "Building-in dimensions" or as cal-culated (see Building-in severalCombiSets). Observe the safety dis-tances (see "Safety distances").
Wooden worktops
000ESeal the cut surfaces with a suitablesealant to avoid swelling caused bymoisture. The sealant must be heat-resistant.
Make sure that the sealant does notcome into contact with the top of theworktop.000EPosition the spring clamps 0011 andspacer bars 0012 on or at...

Installation50Natural stone worktopsYou will need heavy duty double-sidetape (not supplied) to secure thespring clamps and spacer bars.000EStick the tape 0013 to the top edge ofthe cut-out in the positions shown inthe diagram.000EPosition the spring clamps 0011 andspacer bars 0012 on or at the top edgeof the cut-out and press them firmlyinto place.
000EApply silicone to the side and loweredges of the spring clamps 0011 andthe spacer bars 0012.000EThen fill gap 0014 between spacerbar 0012 and the worktop...