Miele 7644 C Manual

Hooking up the drain hose (in sink or
floor drain)
See front view illustration.
If you decide to hook the hose
up to a sink, secure it against being
detached, by clamping it, for
example. Otherwise overflowing
water can cause damage.
Use the bow-shaped holder to
prevent the drain hose from
becoming kinked.
Special installation conditions
requiring a non-return valve
Under special connection
conditions, anon-return valve (kit
available) for external water
disposal(optional accessory) must
be used....

1 Adapter
2 Sink coupling nut
3 Hose clip
4 End of hose
5 Non-return valve
6 Dryer drain hoseFit the adapter to the sink drain outlet
1with the sink coupling nut2.
Usually the sink coupling nut has a
flat washer, which you must remove.
Fit the end of the hose4to the
adapter1.
Using a screwdriver, tighten the hose
clip3directly behind the sink
coupling nut.
Install the non-return valve5so
that the arrow points in the direction
of flow (towards the sink). Otherwise,
pumping out will be impossible....

Electrical connections
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
breakdown, grounding will reduce
the risk of electric shock by
providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an
equipment grounding conductor
and a grounding plug. The plug
must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
WARNING – Improper connection of...

Height 850 mm
Width 595 mm
Depth 634 mm
Depth with door open 1074 mm
Can be pushed under a worktop
–Height
–WidthYes
850 mm
600 mm
Suitable for stacking Yes
Weight 52 kg
Drum Volume 111 liters
Volume of condensed water container approx. 3.5 liters
Hose length 1.50 m
Maximum delivery head 1.50 m
Maximum delivery length 4.00 m
Length of power cord 2.00 m
Voltage
Connected load (Watts)
Rated current (Amps) see data plate
Light bulb wattage
Test certifications granted
Technical data
44 

Programmable functions
for changing
standard values
As needed, you can use
programmable functions to adapt
the dryer electronics to changing
requirements.
You can alter programmable
functions at any time.
45 

Extending the range of drying
levels
You can extend the range of the
drying levels for many of the
programs:
Rotary iron+
(dryer than Rotary Iron).
Hand iron+
(dryer than Hand iron).
Normal +
(dryer than Normal).
Additionally, theExtra dry levelcan
be selectedfor the Mixed and Denim
Jeansprograms.
This programmable function is also
effective in the following programs:
Normal, Wrinkle free*, Mixed*,
Express, Denim/Jeans
(* no Rotary iron+).
For programming and saving in the
memory, follow stepsto.
The...

Adjusting buzzer volume
The buzzer has two volumes.
For programming and saving in
memory, follow stepsto.
This function is programmed using the
buttons.
Precondition:
–The dryer is switched off.
–The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
Press theGentlebutton once.
– TheGentleindicator light flashes
briefly four times.
–
Pand0flash...

Set memory function
The electronics memorizes any
selected program with extra options.
The duration of aSmoothingprogram
will also be stored in memory.
These settings will be used for the
next drying. They can be accepted,
or changed by using the buttons.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press...

Extending cooldown time
You can individually lengthen the
cooldown phase the occurs before
the end of a program. Fabrics will be
more completely cooled down.
Cooldown time
–can be extended by two stages.
–it does not function forSmoothing
programme.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press...

Change function of Filter/Vent
indication
Lint should be removed after drying.
At the same time, theFilter/Vent
indicator light reminds you to do so
as soon as a certain degree of lint
has accumulated. You can yourself
decide which degree of lint
accumulation will trigger that
reminder.
Determine by trial and error which of
the four options responds to your
drying practices.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
–...