Miele 7644 C Manual

Other problems
Problem Cause Solution
The drying
process goes on
too long or even
switches off.
Even after the lint
screen is
cleaned, the
Filter/Vent
indicator come
on.Please check all possible causes and switch the dryer
off and then on again.
Insufficient ventilation,
perhaps because the
installation space is too
small. As a result, room
temperature may rise.Open the door or window, to
prevent room temperature
from rising.
The ventilation inlets beneath
the door are closed.–Remove the blocking...

Problem Cause Solution
Water runs from the
dryer after the
condenser has been
cleaned:–The condenser inner
cover and/or the
condenser have not
been properly inserted
and latched.
–Lint is sticking in the
condenser housing
recess.–Verify that the internal
cover and the
condenser are
correctly and solidly
seated.
–Check their rubber
seals as well.
–Using a cloth, remove
all visible lint from the
heat exchanger recess.
Synthetic laundry items
are statically charged
after drying.Synthetics have a
tendency to...

Problem Cause Solution
TheDress shirts,
Denim/Jeans, and Timed
coldprograms will not
start and the indicator
lights for these programs
do not come on.The cause is not imme
-
diately obvious.–Switch the dryer off and
then on again.
–Select one of the
programs.
–If the program will still
not start, there is a fault.
Contact Miele customer
service.
–Meanwhile, use another
program.
The dryer will not start
when switched on.The cause is not imme
-
diately obvious.–Is the dryer switched
on?
– Is it plugged...

Replacing the light bulb
Disconnect the dryer from the
electrical supply.
Open the door.
The hinged cover for the lighting is over
the port-hole.
Gently insert an ordinary tool* under
the side of the cover.
* such as a wide slot-type screwdriver

Open the cover by pressing lightly
while rotating your wrist.
The cover opens downwards.
The heat-resistant bulb should be
obtained only from Miele customer ser-
vice.
The bulb should be of the same type
and maximum wattage indicated on
the data plate and the...

Repairs
For faults you cannot correct yourself,
please contact:
–the Miele Factory Repair Service.
The telephone number for the
Factory Repair Service is listed at
the back of these operating
instructions.
When contacting the Miele Service
Department, you will need to quote the
model and serial number of your
appliance.
These can be found on the data plate,
visible when the door is open.
Program updates
ThePCoptical interface is used by
Miele customer service to transfer
program updates (PC = Program...

Front view
Power cord
Control panel
Condensed water container
Door
Condenser service accessFour height-adjustable screw feet
Air inlet and outlet vents for cooling
condenser unit
	Condensed water drain hose
(see section "Draining condensed
water externally")
Installation and connection
36 

Rear view
Handgrips under the cover overhang
for moving the appliance (arrows)
Air inlet vent for cooling condenser
unit
Power cord
Condensed water drainage hose
Accessories for connection to a sink
drain outlet
Installation site
This dryer can be accommodated
under a worktop if there is sufficient
height.
Do not install the dryer in a
location where its door could conflict
with room doors.
The appliance top is not
removable.
Carrying the dryer to the installation
site
The rear cover overhang...

Leveling the dryer
To ensure trouble-free operation, the
dryer must be level.

Compensate for floor irregularities by
turning the threaded feet in or out.
Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep
pile carpet etc. This would hinder a
sufficient flow of air to the dryer.
The air inlet/outlet vents on the
front and back must NEVER be
covered. Otherwise, sufficient
condenser cooling cannot be
ensured.
Installation and connection
38 

Ventilating the installation area
Function of Miele condenser dryer:
The condenser dryer separates the
mixture of water and laundry (the
wet load) into water and dry laundry
itself.
The water is heated / evaporated,
then condensed and collected into
condensed water container.
The remaining dry laundry remains
in the drum.
Operation of Miele condenser dryer:
The dryer circulates some air
(trapped with wet laundry inside a
reversibly rotating drum) via lint
filters, heat exchanger and heaters,
in a closed...

Draining condensed water
externally
General
When drying is in progress, the
condensed water is pumped into the
condensed water container through the
drain hose at the back of the dryer.
You can also drain it off externally
through the drain hose - you will no
longer need to empty the condensed
water container.
Hose length................1.50 m
Max. delivery height..........1.50 m
Max. delivery length..........4.00 m
Under special kinds of
connection conditions, this dryer
must be fitted with a...