Miele 7644 C Manual

							Hooking up the drain hose (in sink or
floor drain)
See front view illustration.
If you decide to hook the hose
up to a sink, secure it against being
detached, by clamping it, for
example. Otherwise overflowing
water can cause damage.
Use the bow-shaped holder to
prevent the drain hose from
becoming kinked.
Special installation conditions
requiring a non-return valve
Under special connection
conditions, anon-return valve (kit
available) for external water
disposal(optional accessory) must
be used. This will prevent the
back-flow of water into the dryer and
possible damage.
Such special conditions include:
–
Connection to a sink drain outlet (see
following section).
–
Various kinds of connection, to which
an automatic washer or dishwasher
already in useare also connected.Example: Connection to a sink drain
outlet
The drain hose with non-return valve
can be connected directly to a special
sink drain outlet.
Remove the accessories from the top
of the rear side of the dryer:
Adapter1and the hose clip3behind
it.
Installation and connection
41 
						

							1 Adapter
2 Sink coupling nut
3 Hose clip
4 End of hose
5 Non-return valve
6 Dryer drain hoseFit the adapter to the sink drain outlet
1with the sink coupling nut2.
Usually the sink coupling nut has a
flat washer, which you must remove.
Fit the end of the hose4to the
adapter1.
Using a screwdriver, tighten the hose
clip3directly behind the sink
coupling nut.
Install the non-return valve5so
that the arrow points in the direction
of flow (towards the sink). Otherwise,
pumping out will be impossible.
Insert the non-return valve5into the
dryer drain hose6(make sure it is
connected in the right direction,
check the arrow on the non-return
valve!).
Attach the non-return valve using the
hose clips.
Installation and connection
42 
						

							Electrical connections
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
breakdown, grounding will reduce
the risk of electric shock by
providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an
equipment grounding conductor
and a grounding plug. The plug
must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
WARNING – Improper connection of
the equipment grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or
service representative or personnel
if you are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug provided
with the appliance! If it will not fit the
outlet, have a proper outlet installed
by a qualified electrician.The dryer comes witha5ftlong,
12/4 AWG cord and a NEMA 14-30 P
plug.
It should be connected to a
120/208-240 V, 30 A, 60 Hz AC power
supply. A 3 pole-4 wire grounding
power outlet (NEMA type 14-30 R) is
necessary.
The dryer is equipped with a power
cable and plug ready for connection.
The plug must always be accessible to
facilitate disconnecting the dryer from
the electrical supply.
To eliminate a potential fire source, the
dryer should NEVER be connected by
means of extension cords, or by
multi-outlet power strips or the like.
The appliance data plate indicates the
nominal power consumption and the
approbiate fuse capacity. Please
compare the information on the data
plate with the electrical network data.
Installation and connection
43 
						

							Height 850 mm
Width 595 mm
Depth 634 mm
Depth with door open 1074 mm
Can be pushed under a worktop
–Height
–WidthYes
850 mm
600 mm
Suitable for stacking Yes
Weight 52 kg
Drum Volume 111 liters
Volume of condensed water container approx. 3.5 liters
Hose length 1.50 m
Maximum delivery head 1.50 m
Maximum delivery length 4.00 m
Length of power cord 2.00 m
Voltage
Connected load (Watts)
Rated current (Amps) see data plate
Light bulb wattage
Test certifications granted
Technical data
44 
						

							Programmable functions
for changing
standard values
As needed, you can use
programmable functions to adapt
the dryer electronics to changing
requirements.
You can alter programmable
functions at any time.
45 
						

							Extending the range of drying
levels
You can extend the range of the
drying levels for many of the
programs:
Rotary iron+
(dryer than Rotary Iron).
Hand iron+
(dryer than Hand iron).
Normal +
(dryer than Normal).
Additionally, theExtra dry levelcan
be selectedfor the Mixed and Denim
Jeansprograms.
This programmable function is also
effective in the following programs:
Normal, Wrinkle free*, Mixed*,
Express, Denim/Jeans
(* no Rotary iron+).
For programming and saving in the
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
–
The dryer is switched off.
–
The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
–
TheGentleindicator light flashes
twice briefly.–Pand0flash alternatively in the
display (default setting).
The number appearing alternatively
withPmeans:
0Default setting
IDrying range steps added
(Expressindicator light also flashes)
Pressing theStart/Stopbutton
switches from one to the other.
Using theI-On/0-Offbutton, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
To select the extended drying level:
Select a program.
Press the drying level button
repeatedly until one or two indicator
lights come on.
– Indicator lightsExtra dryandNormal
= Normal+
–
Indicator lightsNormalandHand
iron= Hand iron+
–
Indicator lightsHand ironandRotary
iron= Rotary iron+
Programmable functions
46 
						

							Adjusting buzzer volume
The buzzer has two volumes.
For programming and saving in
memory, follow stepsto.
This function is programmed using the
buttons.
Precondition:
–The dryer is switched off.
–The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
Press theGentlebutton once.
– TheGentleindicator light flashes
briefly four times.
–
Pand0flash alternatingly in the
display (default setting).The number appearing alternatingly
withPmeans:
0Buzzer normal
(default setting)
IBuzzer loud
(Expressindicator light also flashes)
Pressing theStart/Stopbutton
switches from one number to the
other, and you simultaneously hear
the buzzer setting.
Using theI-On/0-Offbutton, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
47 
						

							Set memory function
The electronics memorizes any
selected program with extra options.
The duration of aSmoothingprogram
will also be stored in memory.
These settings will be used for the
next drying. They can be accepted,
or changed by using the buttons.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
Press theGentlebutton twice.
–
TheGentleindicator light flashes
briefly six times.
–
Pand0flash alternatingly in the
display (default setting).The number appearing alternatingly
withPmeans:
IMemory
(Expressindicator light also flashes)
0no Memory
(default setting)
Pressing theStart/Stopbutton
switches from one to the other.
Using theI-On/0-Offbutton, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
48 
						

							Extending cooldown time
You can individually lengthen the
cooldown phase the occurs before
the end of a program. Fabrics will be
more completely cooled down.
Cooldown time
–can be extended by two stages.
–it does not function forSmoothing
programme.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
Press theGentlebutton three times.
–
TheGentleindicator light flashes
briefly seven times.
–
Pand0flash alternatingly in the
display (default setting).The number appearing alternatingly
withPmeans:
0Default setting
IFive minutes longer cooldown time
(Expressindicator light will flash
once)
2Ten minutes longer cooldown time
(Expressindicator light will also flash
twice)
Pressing theStart/Stopbutton
switches from one to the other.
Using theI-On/0-Offbutton, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
49 
						

							Change function of Filter/Vent
indication
Lint should be removed after drying.
At the same time, theFilter/Vent
indicator light reminds you to do so
as soon as a certain degree of lint
has accumulated. You can yourself
decide which degree of lint
accumulation will trigger that
reminder.
Determine by trial and error which of
the four options responds to your
drying practices.
For programming and saving in
memory, follow stepsto.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
PressStart/Stopand keep it pressed
it during steps\015-.
\015Press theI-On/0-Offbutton in.
Wait until theStart/Stopbutton lights up
continuously...
. . . then release theStart/Stop
button.
Press theGentlebutton four times.
–
TheGentleindicator light flashes
once slowly.
–
Pand2flash alternatingly in the
display (default setting).The number appearing alternatingly
withPmeans:
0TheFilter/Ventindicator is
deactivated
ITheFilter/Ventindicator comes on
only when there is a heavy lint
buildup
(Expresscontrol light additionally
flashes once)
2default setting
(theExpressindicator light also
flashes twice)
3TheFilter/Ventindicator will come
on when there is only a light lint
buildup
(TheExpressindicator light also
flashes three times)
Pressing theStart/Stopbutton
switches from one to the other.
Using theI-On/0-Offbutton, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
50