Midway Kart Fury 39in Operations Manual

C.A.R.T. FURY5
CHAPTER 3 SERVICE
To service the Fluorescent Light Assembly… 
Refer to Marquee Service illustration.
Switch off the power to the game machine and unplug the AC line cord.
Lift open the Marquee Housing. Refer to service instructions for Marquee.
Reach up inside the opening in the cabinet and disconnect the power cable from the fluorescent light 
assembly.  
Loosen, but do not remove the screws fastening the assembly to the cabinet.  
Slide the assembly slightly forward to disengage the...

6MIDWAY AMUSEMENT GAMES, LLC 
CHAPTER 3 SERVICE
VIEWING GLASS SERVICE
To service Monitor Bezel… 
Switch off the power to the game machine and unplug the AC line cord.
Lift open the Marquee Housing. Refer to service instructions for Marquee.
Grasp the monitor bezel at the bottom and lift it out of cabinet.  
Perform the desired repair or equipment replacement.
Wipe the bezel clean before reinstallation.
To service the Monitor (CRT)…
We recommend that you read the WARNINGS thoroughly before beginning...

C.A.R.T. FURY7
CHAPTER 3 SERVICE
Switch off the power to the game machine and unplug the AC line cord.
Remove the Control Cabinet, Marquee Housing, and Monitor Bezel. Refer to service instructions for the 
Control Cabinet, Viewing Glass and Monitor Bezel.    
Open the rear cabinet door and disconnect the monitor from the wiring harness and ground wires.  
Remove 4 nuts securing the monitor mounting flanges to the mounting panel.  
Pull the monitor carefully from the cabinet and set aside.
Perform...

8MIDWAY AMUSEMENT GAMES, LLC 
CHAPTER 3 SERVICE
To service the Dashboard… 
Refer to Dashboard Service illustration.
Switch off the power to the game machine and unplug the AC line cord.
Remove the Control Cabinet. Refer to service instructions for Control Cabinet.
Remove the tamper resistant screws from the molded control cabinet cover. Lift the lid off of the cabinet 
and set aside in a safe place.
Label and disconnect all dash wiring, including the ground strap.
Remove the four screws used to...

C.A.R.T. FURY9
CHAPTER 3 SERVICE
To service the Dashboard PCB, continued… 
Remove the tamper resistant screws used to fasten down the dash panel insert. Lift the insert from the 
dash.
Pull out the PCB back plate from the molded dash.  
Remove the ribbon and power cable connections.
Remove the snaps used to fasten the PCB to the back plate. Lift the PCB off the back plate.
Perform the desired repair or equipment replacement. 
Connect the ribbon and power cable to a Dashboard PCB. NOTE: The red...

10 MIDWAY AMUSEMENT GAMES, LLC 
CHAPTER 3 SERVICE
To service Shifter…
Refer to the General Dashboard Service illustration.
Switch off the power to the game machine and unplug the AC line cord.
Remove the Control Cabinet and the Dashboard. Refer to service instructions for Control Cabinet and 
Dashboard.
Remove the tamper resistant screws used to fasten the molded plastic cover on the control cabinet. Lift 
the cover off of the cabinet and set aside.
Label and disconnect all wiring.
Remove the...

C.A.R.T. FURY11
CHAPTER 3 SERVICE
To service Steering Assembly, continued…
Remove 4 flange nuts holding the motor shield, motor and shaft to the wheel assembly (shield not 
required on all cabinets).  
Slide the motor and the shaft off of the assembly.
Perform the desired repair or equipment replacement.
Reinstall and fasten all items in place with the screws provided.
While the steering mechanism is exposed, inspect the belt for splits in the rubber or other signs of wear at 
the edges of the teeth....

12 MIDWAY AMUSEMENT GAMES, LLC 
CHAPTER 3 SERVICE
To service Boost Buttons on the Steering Wheel Hoop, continued…
Unscrew the nut on the button. Lift the button out of the steering wheel hoop.
Perform the desired repair or equipment replacement.
Be sure to solder the cable wires to the button’s switch when reinstalling a button(s). 
Reinstall and fasten all items in place with the screws provided.
To service Control Cabinet Speaker…
This speaker is located just above the pedal assembly. 
Switch off...

C.A.R.T. FURY13
CHAPTER 3 SERVICE
To service Dollar Bill Validator, continued…
Unlock the coin door and swing it open. Read the label affixed to the door for additional information. 
Disassemble the validator and remove material to permit it to fit inside the coin door as illustrated then 
reassemble unit.  
DOLLAR BILL VALIDATOR SERVICE
To service PCB Board Assemblies…
Switch off the power to the game machine and unplug the AC line cord.
Unlock and remove the rear door.  
Remove the screws used to...

14 MIDWAY AMUSEMENT GAMES, LLC 
CHAPTER 3 SERVICE
To service Wheel Driver Board Assembly, continued…
Remove the wheel driver board assembly mounting screws.  Lift the board out of the cabinet and set in 
a safe place. Use anti-static bags and protective containers for storage if not reinstalled immediately.
Perform the desired repair or equipment replacement.
Be certain to reinstall the metal cover so that it seals against the metal cage.
To service the Main Boot, PIC or Sound ROM…
The ROM (Read Only...