Marantz Vp 11s1 DLP Projector User Manual
Here you can view all the pages of manual Marantz Vp 11s1 DLP Projector User Manual. The Marantz manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
23 ENGLISH –Gamma setting To change the type of Gamma curve, set the Picture Mode ( p.22) to User (1 – 9). Select “Gamma” from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or Dynamic). –Color Temp. (Color Temperature) 1 : Red comes out strong. Color temperature is about 5250 K. 2 : Red is mildly strong. Color temperature is about 5800 K. 3 : Normal. Color temperature is about 6500 K. 4 : Blue is mildly strong. Color temperature is about 7500 K. 5 : Blue comes...
Page 32
24 ENGLISH –Cinema Auto : Automatically selects the cinema mode when a video signal is input. NTSC: 3-2 pull down, PAL: 2-2 pull down Off : Pull-down processing is not performed. –VCR Mode On : A projector is forced into the intra-field only deinterlacing mode. Off : A projector is used with external field memories and operates in the full set of deinterlacing modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing using 3:2 pulldown detection (2:2 pulldown for 625/50...
Page 33
25 ENGLISH Standard 1 Component 1 Component 2 S-Video VideoAuto Auto Auto Auto RGB Auto HDMI2 CSC HDMI1 CSC HDMI2 HDMI1 Auto Auto Auto AutoPicture Adjust Fine Menu 1 Fine Menu 2 Input Signal RGB/HD Adjust Display OSD/Blanking Config. Input Signal NTSC(NTSC-3.58) : Conventional analog broadcasting used mainly in USA, Canada, Taiwan, Korea, and Japan. PAL(PAL-4.43) : Conventional analog broadcasting used mainly in United Kingdom and Germany. SECAM : Conventional analog broadcasting used mainly in France...
Page 34
26 ENGLISH –Keystone Adjust trapezoid image to rectangle image. –Scale Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the original size. –Width Reduces the image width without changing the image height. The width can be reduced to about 75% the original size. –Position H, V Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the vertical position of the input signal. –Overscan Selects whether to show or...
Page 35
27 ENGLISH –Auto Power Off When the auto power off feature is set to Enable, power to the projector automatically shuts off if no signals are received and no operations are performed for about 10 consecutive minutes. If 9 minutes pass without the projector receiving any signals or being operated in anyway, the below message appears on the screen. About 1 minute after the message appears on the screen, power to the projector shuts off. Note: After the above message appears on the screen, pressing any...
Page 36
28 ENGLISH CAUTION: •Do not touch the lamp and the lamp unit carelessly. It is extremely hot. Wait at least one hour for the lamp to cool down before handling. •Do not loosen any screws except for those mentioned below. •The lamp may break if handled improperly. •Do not use other than a Marantz replacement lamp unit.❖ How to replace the Lamp Unit PREPARATION: When replacing the lamp, turn off the power for the projector. After the cooling fan stops, disconnect the power cord and wait for one hour until...
Page 37
29 ENGLISH 3. Wait at the least one hour for the lamp and lamp unit to cool down. 4. Read the caution and warning labels on the unit. Lamp cover WARNINGTHIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY. MODEL NO. VP-16S1 / U1M AC 120V 60HZ 2.0ASERIAL NO. CAUTION : HIGH PRESSURE LAMP MAY EXPLODED IF IMPROPERLY HANDLED. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.ATTENTION...
Page 38
30 ENGLISH If the lens becomes dirty or smudged, clean it with a soft dry cloth only. Use optical lens cleaners that are approved for eyeglasses or cameras. Do not use a dampen cloth, detergent solution, or thinner. It may damage the lens and remain as stains. When replacement parts are required, be sure to inform a Marantz authorized service center. Use only replacement parts specified by Marantz. Unauthorized substitutions may result in fire, electric shock, or other hazards. And, the warranty may not...
Page 39
31 ENGLISH Try the following troubleshooting before calling for service.1. Are the connections made properly ? 2. Are you operating the unit properly, following the instructions ? If the unit does not operate properly, check the items shown in the following table. If any trouble cannot be solved by the instructions below, malfunction of the internal circuitry is suspected; immediately unplug the AC power cord and contact Marantz dealer or service center.TROUBLESHOOTINGNo power Image is not displayed....
Page 40
32 ENGLISH WARNING/LAMP indicator, ON indicator, and STANDBY indicator diagnose error mode of the projector as follows. The lamp cover is not closed properly. The lamp has failed, or the lamp is completely worn out. Projector internal temperature is higher than the allowed level. Trouble has occurred with the fan. Internal program error Close the cover correctly. Replace the lamp and reset lamp life.Check if anything is blocking the exhaust vent. Shut power OFF and ON again. OtherFan...