Home > Marantz > Projector > Marantz Vp 11s1 DLP Projector User Manual

Marantz Vp 11s1 DLP Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Marantz Vp 11s1 DLP Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 38 Marantz manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							23
    ENGLISH
    –Gamma setting
    To change the type of Gamma curve, set the Picture Mode (
    
    p.22) to User (1 – 9). Select “Gamma”
    from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or
    Dynamic).
    –Color Temp. (Color Temperature)
    1 : Red comes out strong. Color temperature is about 5250 K.
    2 : Red is mildly strong. Color temperature is about 5800 K.
    3 : Normal. Color temperature is about 6500 K.
    4 : Blue is mildly strong. Color temperature is about 7500 K.
    5 : Blue comes out strong. Color temperature is about 9300 K.
    HB : High Bright : Display brightest image.
    NOTES:
    - To adjust picture quality, set the index to a mode other than the default. See “Picture Mode”. 
    (
    
    P.22)
    - The Gamma cannot be set unless User (1 - 9) is set for the Picture Mode (
    
    P.22).
    - Tint cannot be adjusted for component input, HDMI input or PAL signals. For details, see “Functions
    by Signal.” (
    
    P.20-21)
    - The settings made in Picture Adjust are saved in the currently selected Picture Mode index.
    ABCDE
    TheaterDynamic
    Picture quality in each of the picture modes can be adjusted to your liking and those adjustments can be
    saved in memory. 
    User 1
    Gamma
    Contrast
    Brightness
    Color
    Tint
    0
    0
    03 0
    Lamp Mode Color Temp.
    Normal AIris
    F6.0Aspect
    Full
    C
    D
    E BA
    Picture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    Theater
    Standard
    Dynamic
    Picture Adjust
    Adjustments
    A, B, C, D, E, Theater,
    Standard, Dynamic
    -50Ô
    0Ô
    50
    (Weak) (Default) (Strong)
    -50
    Ô
    0Ô
    50
    (Dark) (Default) (Bright)
    -50
    Ô
    0Ô
    50
    (Light) (Default) (Deep)
    R50
    Ô
    0Ô
    G50
    (Purple) (Default) (Green)
    12345HB
    (Red) (Blue)
    Normal, Economy
    F6.0, F3.0
    Sets the lens aperture. 
    F6.0: Use to prioritize contrast.
    F3.0: Use to prioritize brightness.Full, Normal, Zoom, V-Stretch,
    Through
    Item
    Gamma
    Contrast
    Brightness
    Color
    Tint
    Color Temp. 
    (Color Temperature)
    Lamp Mode
    Iris
    Aspect
    7146@@&/(     1.  
    						
    							24
    ENGLISH
    –Cinema
    Auto : Automatically selects the cinema mode when a video signal is input. 
    NTSC: 3-2 pull down, PAL: 2-2 pull down
    Off : Pull-down processing is not performed.
    –VCR Mode
    On : A projector is forced into the intra-field only deinterlacing mode.
    Off : A projector is used with external field memories and operates in the full set of deinterlacing
    modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing
    using 3:2 pulldown detection (2:2 pulldown for 625/50 sources).
    –Black level
    Select the black level by a video source.
    –FRC (Frame Rate Conversion)
    Auto :Frame Rate Conversion function is basically off. However FRC turns on automatically
    depending on vertical  frequency of input signal.
    On : Frame Rate Conversion function is “On”. (60Hz fixed)
    –CEC (Chroma Error Correction)
    On : Reduces CUE (Chroma Up-sampling Error) of 1080i signals.
    Off : Normally, use this mode.
    –Picture Shift V
    When Aspect on the Picture Adjust menu is set to “Zoom”, this setting allows the user to move the
    projected image vertically in order to see parts on the image not appearing on the screen. 
    –Luminance Gain
    This menu allows the users to set the luminance gain.
    –Chroma Delay
    This menu allows the users to set the chrominance delay.Notes :•There are some parameters can not adjust according to input signal.
    •The settings made in Fine Menu 2 are saved in each currently selected input signal source.Standard 1
    Cinema
    VCR Mode
    Black LevelAuto
    On
    0 IRE
    FRC Auto
    0
    0
    0 Picture Shift V
    Luminance Gain
    Chroma Delay
    Picture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    CEC Off
    Fine Menu 2
    By adjusting this Fine Menu, you can make fine picture adjustment.
    –Sharpness
    Adjust the sharpness.
    –Noise Reduction
    Adjust the noise reduction.
    –R Gain
    This menu allows the users to set the gain for red.
    –G Gain
    This menu allows the users to set the gain for green.
    –B Gain
    This menu allows the users to set the gain for blue.
    –R Bias
    This menu allows the users to set the bias for red.
    –G Bias
    This menu allows the users to set the bias for green.
    –B Bias
    This menu allows the users to set the bias for blue.Note :•The settings made in Fine Menu 1 are saved in the currently selected Picture Mode index (Default
    excluded).
    Standard 1
    Sharpness
    Noise Reduction
    R Gain
    G Gain
    B Gain
    0
    0 R Bias
    G Bias
    B Bias0
    0
    0000
    Picture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    Fine Menu 1
    Adjustments
    050
    050
    -50Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    Item
    Sharpness
    Noise Reduction
    R Gain
    G Gain
    B Gain
    R Bias
    G Bias
    B Bias
    Item
    Cinema
    VCR Mode
    Black level
    FRC
    CEC
    Picture Shift V
    Luminance GainChroma DelayAdjustments
    Auto, Off
    On, Off
    0 IRE, 7.5 IRE /Expand,
    Normal (For HDMI input)Auto, On
    On, Off
    -50
    Ô
    0Ô
    50
    -50
    Ô
    0Ô
    50
    -5
    Ô
    0Ô
    5
    7146@@&/(     1.  
    						
    							25
    ENGLISH
    Standard 1
    Component 1
    Component 2
    S-Video
    VideoAuto
    Auto
    Auto
    Auto
    RGB Auto
    HDMI2
    CSC HDMI1
    CSC HDMI2 HDMI1 Auto
    Auto
    Auto
    AutoPicture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    Input Signal
    NTSC(NTSC-3.58)
    : Conventional analog broadcasting used
    mainly in USA, Canada, Taiwan, Korea, and
    Japan.
    PAL(PAL-4.43)
    : Conventional analog broadcasting used
    mainly in United Kingdom and Germany.
    SECAM
    : Conventional analog broadcasting used
    mainly in France and Russia.
    480p
    : Standard digital broadcasting
    540p
    : Special digital broadcasting 
    (for example: RCA DTC100)
    576p
    : Standard digital broadcasting
    720p, 1080p
    : High Definition digital broadcasting
    1035i
    : Japanese Hi-Vision broadcasting
    –Mode
    Auto: Each item is adjusted automatically.
    Memory1-3: If something wrong with Auto Adjust, select Memory, please adjust each item manually.
    –Readjust
    Select to readjust settings automatically for each item in this menu.
    –Resolution H, V
    Adjusts the horizontal and vertical resolution of the RGB/HD input signals.
    –Position H, V
    Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
    vertical position of the input signal.
    –Phase
    Adjust the phase of the DMD dots and the computer signal input from the RGB IN. Adjust the picture
    to where it looks clearest.
    –Clamp Position, Width
    Adjusts the clamp position and width used in RGB/HD input.
    Standard 1
    Mode
    Readjust
    Resolution H
    Resolution V
    Position H
    Position VMemory 1
    0
    0
    0
    0 Phase
    Clamp Position
    Clamp Width
    000
    Picture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    123
    RGB/HD Adjust
    Item
    Mode
    Readjust
    Resolution H
    Resolution V
    Position H
    Position V
    Phase
    Clamp Position
    Clamp Width
    Adjustments
    Auto, Memory 1, Memory 2, Memory 3Yes, No
    0
    Ô
    25
    (Default) (Large)
    0
    Ô
    25
    (Default) (Large)
    -50
    Ô
    0Ô
    50
    (Left) (Default) (Right)
    -10
    Ô
    0Ô
    10
    (Down) (Default) (Up)
    -10
    Ô
    0Ô
    10
    (Backward) (Default) (Forward)
    -50
    Ô
    0Ô
    50
    (Backward) (Default) (Forward)
    -50
    Ô
    0Ô
    50
    (Small) (Default) (Large)
    Item Adjustments
    Component1, Auto, 480i/576i, 480p, 540p, 576p,
    Component2 720p, 1035i, 1080i, 1080pS-Video Auto, NTSC, PAL, SECAMVideo Auto, NTSC, PAL, SECAM
    RGB Auto, 480i/576i, 480p, 540p, 576p,
    720p, 1035i, 1080i, 1080p
    HDMI 1, HDMI 2 Auto, 480i/576i, 480p, 576p, 720p, 1035i, 1080i, 1080p
    CSC HDMI 1, Auto, RGB, YP
    BPR4:4:4, YP
    BPR4:2:2, 
    CSC HDMI 2 YC
    BCR4:4:4, YC
    BCR4:2:2, 
    Color space conversion select for HDMI input.
    RGB: Color Space Conversion is skipped.
    YP
    BPR: This mode is suitable for HD TV signal
    such a 720p, 1080i.
    YC
    BCR: This mode is suitable for SD TV signal
    such a 480i, 480p.
    7146@@&/(     1.  
    						
    							26
    ENGLISH
    –Keystone
    Adjust trapezoid image to rectangle image.
    –Scale
    Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the
    original size.
    –Width
    Reduces the image width without changing the image height. The width can be reduced to about 75%
    the original size.
    –Position H, V
    Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
    vertical position of the input signal. 
    –Overscan
    Selects whether to show or hide picture borders with NTSC, PAL, SECAM, 480i, 480p, 576i and 576p
    signals.
    Enable: Does not display borders of image signals. (Normally, use this mode.)
    Disable: Displays the entire image signal.
    –Instllation
    Sets the installation mode of the projector.
    Front: Select to set the projector on a tabletop and project from in front of the screen.
    Rear: Select to set the projector on a tabletop and project from behind the screen.
    F + Ceiling: Select to mount the projector on the ceiling and project from in front of the screen.
    R + Ceiling: Select to mount the projector on the ceiling and project from behind the screen.
    Standard 1
    Keystone
    Scale
    Width
    Position H
    Position V
    Installation
    0
    0
    00
    0Front
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    Overscan
    Enable
    Display
    –Menu Position
    OSD position is selected from 9 positions.
    –Status Info.
    Enable: Displays the current status of the projector for a set amount of time in the upper right-hand
    corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or
    other setting is changed.
    Disable: Does not display Status Info.
    –Power-OFF Confirm.
    Disable:
    Directly puts the projector on standby without displaying the confirmation message when power
    is shut off from the  button on the remote controller or the 
    /Ibutton on the projector.
    Enable:Displays a confirmation message asking whether to shut the power off or continue use
    when power is shut off from the  button on the remote controller or the /Ibutton on the
    projector. To shut off the power immediately, select “Yes” and press the ENTERbutton. To
    not shut off the power, select “No” and press the ENTERbutton.
    –Blanking Memory
    Sets the blanking mode with which part of the screen can be hidden in black bands. To use this mode
    or change the setting, select from Memory 1 to 3.
    Off: Turns the blanking mode off. No masking occurs.
    Memory 1-3:Memorize the blanking width of the top, bottom, left and right masks set with the
    below features. Up to three settings can be memorized.
    –Blanking Top, Bottom, Left and Right
    Set the blanking width of the top, bottom, left and right masks, which are then memorized in Memory 1
    – 3 of Blanking Memory. Each can be set from 0 (no mask) to a maximum 100.
    Standard 1
    Menu Position
    Language
    Status Info.
    Power-OFF Confirm.
    Blanking Memory
    Blanking TopTop-L
    English
    Enable
    Enable
    Memory 1
    0
    0
    0
    0 Blanking Bottom
    Blanking Left
    Blanking RightPicture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    OSD/Blanking
    Item
    Menu Position
    Language
    Status Info.
    Power-OFF Confirm.
    Blanking Memory
    Blanking Top
    Blanking Bottom
    Blanking Left
    Blanking RightAdjustments
    Top-L, Top, Top-R, Center-L, Center, Center-R, 
    Bottom-L, Bottom, Bottom-REnglish, Deutsch, Français, Español,
    Português, Italiano Enable, Disable 
    Enable, Disable
    Off, Memory 1, Memory 2, Memory 3
    0 100
    0 100
    0 100
    0 100
    Keystone
     
    (Electronic vertical 
    keystone correction)Scale
    Width
    Overscan
    Installation
    Item Adjustments
    -100 0-25 250(Min)
    (Min) (      )
    (      )
    (      )
    Position H
    Position V
    -50 500
    (Left) (Right)(Default)-50 500
    (Down) (Up)(Default)(Max)-100 0
    (Max)
    Enable, Disable
    Front, Rear, F+Ceiling,
    R+Ceiling
    7146@@&/(     1.  
    						
    							27
    ENGLISH
    –Auto Power Off
    When the auto power off feature is set to Enable, power
    to the projector automatically shuts off if no signals are
    received and no operations are performed for about 10
    consecutive minutes. If 9 minutes pass without the
    projector receiving any signals or being operated in
    anyway, the below message appears on the screen.
    About 1 minute after the message appears on the screen, power to the projector shuts off.
    Note:
    After the above message appears on the screen, pressing any button on the projector or remote
    control other than the / Ibutton on the projector and the ONor STANDBYbuttons on the remote
    control resets the auto power off feature. 
    The auto power off feature will activate again if, after that, the projector goes without receiving any
    signals or being operated in anyway for 10 consecutive minutes.
    –Tigger 2
    Select either 12V output or 0V output by choosing On or Off for each aspect mode. Full, Normal,
    Zoom, V-stretch and Through.
    This allows you to control such as a powered dual aspect screen with the outputs for the aspect
    modes.
    On: Output DC 12V.
    Off: No output.
    Standard 1
    Auto Power Off
    Trigger 2 Full
    Trigger 2 Normal
    Trigger 2 ZoomEnable
    On
    On
    On
    Trigger 2 V-stretch On
    Trigger 2 Through On
    Reset Lamp Life
    Reset All Remote Control
    Picture Adjust
    Fine Menu 1
    Fine Menu 2
    Input Signal
    RGB/HD Adjust
    Display
    OSD/Blanking
    Config.
    Configration
    Item
    Adjustments
    Auto Power Off
    Enable, Disable
    Trigger 2 Full On, OffTrigger 2 Normal On, OffTrigger 2 Zoom On, OffTrigger 2 V-stretch On, OffTrigger 2 Through On, OffRemote Control
    Wireless, Wired
    Reset Lamp Life Yes, NoReset All Yes, No
    –Remote Control
    Wireless: Set to use the included remote controller.
    Wired:Set to control the projector from either Marantz’s AV components connected to the
    REMOTE CONTROL IN/OUT terminals or a PC or other device connected to the RS-
    232C terminal of the projector. The included remote controller cannot be used in this case.
    When this item is selected, a confirmation message appears asking whether to change the currently
    selected mode to the other mode or not. To change the mode, select “Yes” and press the ENTER
    button on the projector. To keep the same mode, select ‘No” and press the ENTERbutton.
    Notes:
    - To prevent misoperation, the ENTERbutton of the remote controller does not respond to touch
    when the Wired/Wireless setting is displayed. Press the ENTERbutton of the projector to enter the
    setting.
    - To change from Wired to Wireless, set “Wireless” from the menu using the buttons of the projector.
    –Reset Lamp Life
    If the lamp is replaced before reaching its 2000 hours
    lamp life, be sure to reset the lamp’s life counter. To do
    this, select “Reset Lamp Life” from the Configuration
    menu. When the user selects this item, the following
    message appears:
    Select “Yes”, and press the ENTERbutton. Then the
    lamp life is initialized.
    –Reset All
    All settings are reset to the factory default settings except
    the lamp life.
    When the user selects this item, the following message
    appears:
    Select “Yes”, and press the ENTERbutton.
    Ye s N oReset Lamp Life
     ?
    Reset All
     ?
    Ye s N o
    It will be standby mode soon.Auto Power Off
    7146@@&/(     1.  
    						
    							28
    ENGLISH
    CAUTION:
    •Do not touch the lamp and the lamp unit
    carelessly. It is extremely hot. Wait at least
    one hour for the lamp to cool down before
    handling.
    •Do not loosen any screws except for those
    mentioned below.
    •The lamp may break if handled improperly.
    •Do not use other than a Marantz
    replacement lamp unit.❖
    How to replace the Lamp Unit
    PREPARATION:
    When replacing the lamp, turn off the power for
    the projector. After the cooling fan stops,
    disconnect the power cord and wait for one
    hour until the lamp is cooled down completely,
    then replace the lamp.1.
    Press the STANDBYbutton on the remote
    controller or the / Ibutton on the projector
    to turn the projector off.
    2.
    After the cooling fan stops, Unplug the AC
    power cord.
    C1 C2 S G1
    H1 H2 V G2A1A2 RGB G3
    COMP.1 COMP.2 S-VIDEO USER
    HDMI 1 HDMI 2 VIDEO
    AUX 1 AUX 2
    ON
    STANDBYIRIS LAMP
    C.TEMP GAMMA
    Replacing Lamp Unit
    MAINTENANCE
    ❖
    Lamp Life
    Display the remaining lamp life by pressing the
    INFO. button on the remote controller.
    Notes:
    •The maximum life limit of the lamp is 2,000
    hours. Although we care very much about
    quality, the lamp can rarely breaks down if
    running time exceeds 1,000 hours.
    Therefore we recommend to replace the
    lamp if Lamp Life gets under 1,000 hours.
    The lamp cannot be used exceeding the
    maximum life limit.
    •This product is checked under strict quality
    control when it is shipped out form factory.
    “Total Hours” in the menu includes the time
    for this check. So “Total Hours” may not be 0
    hours when it is used first time.
    INPUT
    ENTER
    ASPECT
    CINEMA
    VCR MODE
    BLACK LEVEL
    PATTERN
    BLACKINFO.I A
    InformationVideo Input Component 2 -480p
    Picture Mode User 1
    Gamma A
    Aspect Normal
    Lamp Mode Economy 
    Iris F6.0
    Lamp Life 921 Hours
    Total Time 3653 Hours
    Lamp Life and Replace Lamp
    –When the lamp life becomes less than 100
    hours and the unit is still on, the remaining
    lamp life is displayed on the screen
    automatically.
    –When the lamp life becomes less than 5 hours,
    the remaining lamp life is displayed on the
    screen .
    To clear the warning, press the MENUbutton.
    –Approximately 2 minutes after the lamp
    reaches the end of its lamp life, power to the
    projector shuts OFF and the WARNING
    indicator lights up a yellow color. If the below
    message appears on the screen and power
    shuts OFF soon thereafter, promptly replace
    the lamp with a new one. (See “Replacing
    Lamp Unit” 
    
    P.28)
    Lamp Life 0 HoursWarning
    INPUT V-MUTE
    ENTERMENU
    A1A2 RGB G3
    STD DYNIM
    A
    G4
    THTRBLANKINGB1
    OFFB3B2
    Lamp Life 5 HoursWarning
    Warning
    Lamp Life 100 Hours
    ❖
    Initialize the Lamp Life
    The lamp has a lamp life of 2000 hours. The
    projector is designed to shut OFF power if the lamp
    is used beyond this 2000 hours lamp life. In such
    case, replace the lamp and reset the lamp life
    counter as follows.1.
    After the message “Lamp Life 0 Hours”
    appears, power to the projector shuts OFF.
    Promptly replace the lamp with a new one.
    (
    P.28“Replacing Lamp Unit”)
    2.
    Once the lamp has been replaced, press the
    ONbutton on the remote control or the / I
    button on the projector. 
    The below message appears on the screen
    for 120 seconds.
    3.
    Select “Yes”, using the 
    1/2buttons.
    4.
    Press the ENTERbutton. The lamp life
    indicator is now initialized.
    INPUT V-MUTE
    ENTERMENU
    ASPECT
    CINEMA
    VCR MODE
    BLACK LEVEL
    PAT T E R N
    BLACKINFO.
    C1 C2 S G1
    H1 H2 V G2A1
    A2 RGB G3
    STD DYN
    I M
    AG4
    THTRCOMP.1 COMP.2 S-VIDEO USER
    HDMI 1 HDMI 2 VIDEO
    AUX 1
    BLANKING AUX 2
    ON
    STANDBYIRIS LAMP
    C.TEMP GAMMA
    B1
    OFF
    B3
    B2
    2.
    4.3.3.
    2. 4.
    New Lamp
     ?
    Ye s N o
    7146@@&/(     1.  
    						
    							29
    ENGLISH
    3.
    Wait at the least one hour for the lamp and
    lamp unit to cool down.
    4.
    Read the caution and warning labels on the
    unit.
    Lamp cover
    WARNINGTHIS COVER IS PROVIDED WITH
    INTERLOCK TO REDUCE THE RISK OF
    EXCESSIVE ULTRAVIOLET RADIATION.
    DO NOT DEFEAT ITS PORPOSE OR
    ATTEMPT TO SERVICE WITHOUT
    REMOVING COVER COMPLETELY.
    MODEL NO. VP-16S1
     / U1M
    AC 120V   60HZ   2.0ASERIAL NO.
    CAUTION : HIGH PRESSURE LAMP 
    MAY EXPLODED IF IMPROPERLY HANDLED. 
    REFER SERVICING TO QUALIFIED SERVICE 
    PERSONNEL.ATTENTION :  LA LAMPE SOUS 
    HAUTE PRESSION PEUT SI ELLE, NEST 
    PAS MANIPULEE CORRECTEMENT, 
    CONFIER LOPERATION A UN 
    PERSONNEL DENTRETIEN QUALIFIE.CAUTION HOT : UNPLUG 
    THE POWER CORD AND WAIT 
    60 MINUTES BEFORE CHARGING 
    THE LAMP.ATTENTION CHAUD :  DEBRANCER LE CORD ON 
    DALOMENTION ET ATENDER 
    60 MINUTES AVANT DE 
    CHANGER LAMPE.
    M MODEL NO. VP-12S1
     / N1S
    MADE IN JAPAN
    FABRIQUE AU  JAPON
    AC 120V   60H
    Z   2.0W
    SERIAL NO.
    CAUTION : 
    HIGH PRESSURE LAMP 
    MAY EXPLODED IF IMPROPERLY HANDLED. 
    REFER SERVICING TO QUALIFIED SERVICE 
    PERSONNEL.
    ATTENTION :  
    LA LAMPE SOUS 
    HAUTE PRESSION PEUT SI ELLE, NEST 
    PAS MANIPULEE CORRECTEMENT, 
    CONFIER LOPERATION A UN 
    PERSONNEL DENTRETIEN QUALIFIE.
    CAUTION HOT : 
    UNPLUG 
    THE POWER CORD AND WAIT 
    60 MINUTES BEFORE CHARGING 
    THE LAMP.
    ATTENTION CHAUD :  DEBRANCER LE CORD ON 
    DALOMENTION ET ATENDER 
    60 MINUTES AVANT DE 
    CHANGER LAMPE.
    WARNING
    THIS COVER IS PROVIDED WITH
    INTERLOCK TO REDUCE THE RISK OF
    EXCESSIVE ULTRAVIOLET RADIATION.
    DO NOT DEFEAT ITS PORPOSE OR
    ATTEMPT TO SERVICE WITHOUT
    REMOVING COVER COMPLETELY.
    M
    CAUTION  HIGH PRESSURE LAMP MAY EXPLODED IF 
    IMPROPERLY HANDLED. REFER SERVICING 
    TO QUALIFIED SERVICE PERSONNEL.ATTENTION LA LAMPE SOUS HAUTE PRESSION PEUT 
    EXPLOSER SI ELLE, NEST PAS MANIPULEE 
    CORRECTEMENT, CONFIER LOPERATION 
    A UN PERSONNEL DENTRETIEN QUALIFIE.
    VORSICHT
     :
    BEI FALSCHER HANDHABUNG 
    KANN DIE HOCHDRUCKLAMPE 
    EXPLODIEREN UBERLASSEN 
    SIE WARTUNGSARBEITEN 
    NUR FACHPERSONAL.
    CAUTION HOT UNPLUG THE POWER CORD AND 
    WAIT 60 MINUTES BEFORE 
    CHANGING THE LAMP.ATTENTION CHAUD  DEBRANCER LE CORD ON 
    DALIMENTION ET ATENDER 60 
    MINUTES AVANT DE CHANGER 
    LAMPE.WARNUNG HEISS
     
    ZIEHEN SIE DEN NETZSTECKER 
    AB UND WARTEN SIE 60 MINUTEN, 
    BEVOR SIE DIE GLUHLAMPE 
    WECHSELN.AA
    B
    BFor USA
    For Europe
    For USA
    For Europe
    5.
    Remove the lamp cover screw.
    6.
    Remove the lamp cover in the direction of the
    arrow.
    7.
    Open the cover sheet and remove the two
    screws (slotted head screwdriver required)
    that lock down the lamp unit. Do not remove
    any other screws.
    8.
    Holding the handle and pull the lamp unit out
    toward your side.
    9.
    Install a new lamp unit in position securely.
    10.
    Lock the lamp unit in place with the two
    screws removed in step 7. Press on the
    handle until it folds over and close the cover
    sheet.
    11.
    Install the lamp cover back in its original
    position and fasten with the fastening screw.
    12.
    Plug in the video projector and turn on the
    power and project the image.
    •If the lamp is replaced before reaching its
    2000 hours lamp life, see “Reset Lamp Life”
    (
    P.27).
    •If the lamp is replaced after reaching its
    2000 hours lamp life, see “Initialize the Lamp
    Life”(
    P.28).
    (b)(a)
    Lamp cover
    Cover sheetLamp unit
    7146@@&/(     1.  
    						
    							30
    ENGLISH
    If the lens becomes dirty or smudged, clean it with
    a soft dry cloth only. Use optical lens cleaners that
    are approved for eyeglasses or cameras. Do not
    use a dampen cloth, detergent solution, or thinner.
    It may damage the lens and remain as stains.
    When replacement parts are required, be sure to
    inform a Marantz authorized service center. Use
    only replacement parts specified by Marantz.
    Unauthorized substitutions may result in fire,
    electric shock, or other hazards. And, the warranty
    may not be guaranteed.Replacement PartsCleaning the Lens
    Lamp Unit : LU-12VPS3
    Ceiling Mount kit : MOUNT 20
    This kit is specially designed to mount the unit
    on ceiling.
    Extension Pole : EXT-10
    This tool is to adjust height with the Ceiling
    Mount Kit MOUNT 20.
    CAUTION
    :
    For ceiling installation, consult with the
    Marantz Authorized dealer.Optional Accessories
    7146@@&/(     1.  
    						
    							31
    ENGLISH
    Try the following troubleshooting before calling for service.1.
    Are the connections made properly ?
    2.
    Are you operating the unit properly, following the instructions ?
    If the unit does not operate properly, check the items shown in the following table.
    If any trouble cannot be solved by the instructions below, malfunction of the internal circuitry is suspected; immediately unplug the AC power cord and contact
    Marantz dealer or service center.TROUBLESHOOTINGNo power
    Image is not
    displayed.
    Poor color.
    Picture is too dark.
    Picture is not clear.
    Picture rolls.
    The Remote
    Controller does not
    work.
    Possible Cause SymptomRemedy
    Notes:
    •If the lamp still does not function after the replacement and initialization of the lamp life, contact a Marantz authorized dealer, or service center.
    •This projector uses a microcomputer. External noise can cause malfunctions. In such case, shut power OFF and unplug the power cable from AC power
    outlet. Then, plug the AC power cable back in, press the / Ibutton on the projector or the ONbutton on the remote control and check operation.
    AC power cord is not connected correctly.
    Lamp cover is not closed correctly. 
    A signal cable is not connected correctly.
    Selected input is incorrect.
    The picture mute is active.
    Picture is not adjusted properly.
    Lamp life is running out.
    Contrast or brightness is not adjusted properly.
    Picture is out of focus.
    Dew is on the lens.
    A signal cable is not properly connected.
    Batteries are exhausted.
    The distance to the unit is too far.
    IR sensor on unit is obstructed.
    The “Wired” position in the Menu is selected.Connect the AC power cord properly.
    Close the cover properly. (
    
    P.28)
    Connect a signal cable properly.
    Select the correct input source. (
    P.16)
    Press the V-MUTE button to release the mute.
    Adjust the picture in the MENU mode.
    Replace the lamp. (
    
    P.28)
    Adjust contrast or brightness properly.
    Adjust the focus. (
    
    P.11)
    Run the projector for about two hours.
    Connect a signal cable properly.
    Replace batteries. (
    P.8)
    Make the distance between the unit and the remote control
    closer. (
    
    P.8)
    Remove any obstacles.
    Select the “Wireless”position. (
    
    P.27)
    7146@@&/(     1.  
    						
    							32
    ENGLISH
    WARNING/LAMP indicator, ON indicator, and STANDBY indicator diagnose error mode of the projector as follows.
    The lamp cover is not 
    closed properly.
    The lamp has failed, or 
    the lamp is completely 
    worn out.
    Projector internal 
    temperature is higher 
    than the allowed level. 
    Trouble has occurred 
    with the fan.
    Internal program error
    Close the cover correctly.
    Replace the lamp and 
    reset lamp life.Check if anything is 
    blocking the exhaust vent.
    Shut power OFF and 
    ON again.
    OtherFan TemperatureLamp Lamp cover
    Flashing
    Flashing
    FlashingON
    ON
    OFF
    OFF
    OFF OFF
    OFF
    Flashing
    ON
    OFF Flashing
    OFF
    Indicators
    Error mode
    WARNING
    /LAMPON STANDBYPossible Cause Recommendation
    ERROR MODENO SIGNAL
    REPLACE LAMP!
    OUT OF RANGENo input signal.
    The lamp has reached the end of its life.
    Improper signal feed to the projector.Properly connect the cables.
    Replace the lamp and reset lamp life.
    Adjust resolution, V(Hz) : refresh rate of the
    equipment, referring to the Timing Chart.
    Meaning Message
    Remedy
    Use the list below to check the message displayed on the screen.ON SCREEN MESSAGE
    7146@@&/(     1.  
    						
    All Marantz manuals Comments (0)

    Related Manuals for Marantz Vp 11s1 DLP Projector User Manual