Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 System Description Instructions Manual

							DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Site Requirements 
31 Floor-Plan Guidelines 
Floor-Plan Guidelines
DEFINITY ECS floor plans vary with the size and shape of the equipment room and the 
extent of future growth. Future growth includes a new or upgraded system, adjuncts and 
peripherals, and the cross-connect field. See ‘‘Cross-Connect Field’’ on page 41.
For floor standing cabinets, reserve the area behind a cabinet for the cross-connect field 
and the cable slack manager. For wall mounted cabinets, reserve the area beside the 
cabinets for the cross-connect field. Figure 10 through Figure 15 show typical floor plans. 
All dimensions are shown in inches. Refer to Table 11 for power requirements.
Compact Modular Cabinet (CMC) 
Configuration Guidelines
The cross-connect field is either to the rear or right of the cabinet. To allow service 
access, the table for the management terminal and optional printer is away from the 
equipment area. See Figure 10 and ‘‘Table Area’’ on page 40 for requirements. In an 
installation where no cross-connect field is present, an cross-connect field can be 
installed in the CMC right panel. 
The following steps are pre-installation guidelines:
1. Locate the power outlets outside the cross-connect field area. The outlets must not 
be controlled by a wall switch or be shared with other equipment.
2. Locate the trunk/auxiliary field inside the cross-connect field, if desired.
3. Ground the system. See ‘‘Approved Grounds’’ on page 62.
4. Each cabinet requires either: NEMA 5-15R receptacle
(or equivalent) for United States installations or local IEC 320 
cord set (or equivalent) for non-United States installations. 
						

							Site Requirements 
32 Floor-Plan Guidelines 
DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Figure 10. Typical Compact Modular Cabinet Floor Plan
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
Cross-connect field
Electrical
outlets
Ta b l e
PrinterSystem
management
terminalOptional SMT
12”
12” 12”25.5”
48” Compact
modular
cabinet
Wall
fpdftfp4 LJK 121399 
						

							DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Site Requirements 
33 Floor-Plan Guidelines 
Single-Carrier Cabinet Configuration Guidelines
The cross-connect field can be directly behind the cable slack manager. To allow service 
access, the table for the management terminal and optional printer is away from the 
equipment area. See Figure 11 and ‘‘Table Area’’ on page 40 for requirements.
The following steps are pre-installation guidelines:
1. Locate the power outlets outside the cross-connect field area. The outlets must not 
be controlled by a wall switch or be shared with other equipment.
2. Locate the trunk/auxiliary field inside the cross-connect field, if desired.
3. Ground the system. See ‘‘Approved Grounds’’ on page 62.
4. For fiber connections between PNs, use a 20-foot (6.1 m) multimode fiber optic 
cable.
5. Install earthquake protection (if required). See ‘‘Earthquake Protection’’ on page 
71.
6. Each cabinet requires either: NEMA 5-15R, NEMA 5-20R receptacle (or 
equivalent) for United States installations or local 
cord set (or equivalent) for non-United States installations. 
						

							Site Requirements 
34 Floor-Plan Guidelines 
DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Figure 11. Typical Single-Carrier Cabinet Floor Plan
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
LAN
connectionCross-connect field
Cable
slack
managerProcessor
port
network
cabinet(s)
(front)
Electrical
outlets
Ta b l e
Optional SMT
Printer
Wall
38
22
3227
System
management
terminal
fpdfscc1 LJK 121399 
						

							DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Site Requirements 
35 Floor-Plan Guidelines 
Multi-Carrier Cabinet Configuration 
Guidelines
The cross-connect field is directly behind the cable slack manager. To allow service 
access, the table for the management terminal and optional printer is away from the 
equipment area. See Figure 12 and ‘‘Table Area’’ on page 40 for requirements. The 
following steps are pre-installation guidelines:
1. Locate the power outlets outside the cross-connect field area. The outlets must not 
be controlled by a wall switch or be shared with other equipment.
2. For the PPN cabinets, use either a NEMA 5-50R receptacle (or equivalent) or a 
NEMA L14-30R receptacle (or equivalent) power outlet or: 220 VAC, 50-60 Hz 
power outlet for the Global AC Cabinet.
3. For the Auxiliary Cabinet, use a NEMA 5-20R receptacle (or equivalent).
4. Allow at least 3 feet (91.4cm) of space in front of the cabinet to permit the door to 
open.
5. Ground the system. See ‘‘Approved Grounds’’ on page 62.
6. Install earthquake protection (if required). See ‘‘Earthquake Protection’’ on page 
71.
7. Locate the LAN connection field inside the cross-connect field, if desired.
8. Fiber connections between PNs use a 20-foot (6.1 m) multimode fiber optic cable. 
						

							Site Requirements 
36 Floor-Plan Guidelines 
DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Figure 12. Typical Multi-Carrier Cabinet Floorplan
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
Cross-connect field
Cable
slack
manager
(optional) Cable
slack
manager
Por t
network
cabinet
(front)Auxiliary
cabinet
(optional)
Electrical
outlets Electrical
outlet
Ta b l e
Printer
Wall
38
2828
3232
LAN connection
fpdfmcc1 LJK 121399
System
management
terminal
Optional SMT 
						

							DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Site Requirements 
37 Floor-Plan Guidelines 
Additional Floor Plans
The following floor plans illustrate recommendations for other possible installations. See 
Figure 13, Figure 14, Figure 15, and Figure 16.
Figure 13. Typical Floor Plan with EPN and Auxiliary Cabinet
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
LAN connectionCross-connect field
Cable
slack
manager
(optional)Cable
slack
manager
(optional) Cable
slack
manager
PPN
cabinet
(front)EPN
cabinet
(optional)Auxiliary
cabinet
(optional)
Electrical
outlet
Ta b l e
Printer
Wall
38
2828
323232
fpdftfp1 LJK 121399
System
management
terminal
Optional SMT 
						

							Site Requirements 
38 Floor-Plan Guidelines 
DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Figure 14. Typical Floor Plan with an additional EPN and Auxiliary Cabinets
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
LAN connectionCross-connect field
Ta b l e
Printer
Wall
38
28
Cable
slack
manager
(optional) Cable
slack
manager
PPN
cabinet
(front)EPN
cabinets
(optional)28
32
Cable
slack
manager
(optional)
Auxiliary
cabinet
(optional)
32
Cable
slack
manager
(optional)
Auxiliary
cabinet
(optional)
3232
fpdftfp3 LJK 121399
System
management
terminalElectrical
outlets Electrical
outlet
Optional SMT 
						

							DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Site Requirements 
39 Floor-Plan Guidelines 
Figure 15. Typical Floor Plan with Battery Cabinets
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
LAN connectionCross-connect field
Cable
slack
manager
(optional)Cable
slack
manager
(optional) Cable
slack
manager
PPN
cabinet
(front)
Battery
cabinet
(optional)Battery
cabinet
(optional) EPN
cabinet
(optional)Auxiliary
cabinet
(optional)
Electrical
outlet
Ta b l e
Printer
38
2828
21
323232
5555
fpdftfp5 LJK 121399
System
management
terminal
Wall
Optional SMT 
						

							Site Requirements 
40 Floor-Plan Guidelines 
DEFINITY Enterprise Communications Server Release 8.2
System Description  555-233-200  Issue 1
April 2000
Figure 16. Typical Floor Plan with ATM Switch (Category A only)
NOTE:
To provide power for testing equipment and peripherals, locate electrical 
outlets at intervals that are in accordance with local codes. Also, ensure 
that you locate the main shutoff switch near the door in accordance with 
local codes.
Ta b l e  A r e a
Reserve the table area in the equipment room for the management terminal and optional 
printer, if so equipped. Terminals require approximately 3.2 square feet (0.3 square m) of 
area. 
LAN connection
AT M
switchCross-connect field
Cable
slack
manager
(optional)Cable
slack
manager
(optional) Cable
slack
manager
PPN
cabinet
(front)EPN
cabinet
(optional)Auxiliary
cabinet
(optional)
Electrical
outlet
Ta b l e
Printer
Wall
38
2828
323232
fpdftfp6 LJK 121399
System
management
terminal
Optional SMT