LG Wd 14440fds Owners Manual

							50
ow to use washerH
• If the washer encounters a fault during
operation, the associated fault will be
displayed.
“       ” : Water pressure sensing error
“       ” : Problem of overfilling water
“       ” : Door is not closed
“       ” : Over load in motor
“       ” : Water inlet trouble
“       ” : Drainage trouble
“       ” : Unbalanced load
“       ” : Water temperature trouble
“       ” : Water leaks
“       ” : The washer experienced a
power failure.
If these error letters are displayed, please
refer to the troubleshooting page55 and
follow the guide.
Display
• When Child lock is selected, the
“      ” lamp is on.
• When time delay is selected, it shows
the remaining times to finish the selected
program.
• When washing cycle is completed, 
“            ” is displayed on the “Multi display”.
• During washing cycle, the remaining washing
time is displayed.
• Recommended program by manufacturer.
❋ (   ) : WD-14440(5)FDS
- Cotton :around 1 hour and 54(51) minutes
- Synthetic :around 1 hour and 24 minutes
- Delicate :around 1 hour and 12 minutes
- Hand Wash/Wool : around 57 minutes
- Quick 30 :around 30 minutes
- Duvet :around 1 hour and 12 minutes
- Baby Care :around 2 hours and 37 minutes
- Rinse + Spin :around 26(23) minutes
- Refresh :around 19 minutes
•  The washing time may vary  by the amount
of laundry, water pressure, water
temperature and other washing conditions.
•  If an unbalanced load is detected or if the
suds removing program operates, the wash
time may be extended.
(Max. increasing time is 45 minutes.)
1. Special function display
3. Completion of washing
4. Time left
2. Self diagnose display
Est. Time Remaining
Status Indicator
• This display shows  the estimated time
remaining in the cycle when operating.        
• This washer automatically detects the
wash load (weight) and optimizes the
washing time. After detecting, the display
will show the adjusted time remaining.         
• It shows elapsed time of the cycle the
washer is  operating.
  
						

							51
aintenanceM
The water inlet filter
-         error message will blink on the control panel  when water does not enter the
detergent  drawer.
- If water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
❋ Before cleaning the washer interior, unplug the electrical  power cord to avoid electrical
shock to avoid electrical shock hazards.
❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable
the door lock to prevent young children being trapped inside.
1.Turn off the water tap.
2.Unscrew the water inlet hose.
3.Clean the filter using a hard bristle
brush.
4. Tighten up the inlet hose.
  
						

							52
aintenanceM
3
2
3
2
1
100
The drain pump filter
❋ The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
CAUTIONFirst drain using the drain hose and then open the pump filter to
remove whatever any threads or objects.
Be careful when draining if the water is hot.
❋ Allow the water to cool down before cleaning the drain pump, carrying out
emergency emptying or opening the door in an emergency.
!
1.Open the lower cover cap (H
						

							53
aintenanceM
Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally   with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
MAXMAXMAXMAX
The washing drum
• If you live in a hard water area, limescale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be
replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal
articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
❋ Descaler may contain chemicals that may damage part of your washing machine.
❋ Remove any spots with a stainless steel cleaning agent.
❋ Never use steel wool.
  
						

							54
aintenanceM
The water circulation nozzle & Steam nozzle
• Clean the water circulation nozzle and Steam nozzle, if clogged.
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive 
household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
❋ IMPORTANT: Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass. 
Run washer through a complete cycle using hot water. 
Repeat process if necessary.
Winterizing instructions
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures, follow these instructions to prevent damage to the washer:
1. Turn off  water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer, drain and dry excessive water from the compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer
through a complete cycle using detergent. Do not add wash load.Remove hard water deposits using only cleaners labeled as safe for washing
machine.
NOTE
  
						

							55
roubleshooting guide
❋This washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider. 
Symptom Possible Cause Solution
Rattling and 
clanking noise
Thumping sound
Vibrating noise
Water leaks.
Oversudsing
Water does not enter
washer or it enters
slowly
Water in the washer
does not drain or
drains slowly.•Foreign objects such as coins or
safety pins maybe in drum or
pump.
•Heavy wash loads may produce
a thumping sound. This is usually
normal.
•Have all the transit bolts and
packing been removed?
•Are all the feet resting firmly on
the ground?
•Fill hoses or drain hose are loose
at tap or washer.
• House drain pipes are clogged.
• Water supply is not adequate in
area.
•Water supply tap is not
completely open.
• Water inlet hose(s) are kinked.
•The filter of the inlet hose(s) are
clogged.
• Drain hose is kinked or clogged.
• The drain filter is clogged.Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted,  call your authorized
service centre.
If sound continues, washer is 
probably out of balance. Stop and
redistribute wash load.
If not removed during
installation, refer to Installation guide   
for removing transit bolts. 
Wash load may be unevenly
distributed
in drum. Stop washer and 
rearrange wash load.
Check and tighten hose connections.
Unclog drain pipe. Contact plumber
if necessary.
Too much detergent or unsuitable 
detergent may cause excessive 
foaming which may result in water 
leaks.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
Clean and straighten the drain hose.
Clean the drain filter.
T
  
						

							56
roubleshooting guide
Washer does not start
Washer won’t spin
Door does not open
Wash cycle time
delayed•Electrical power cord may not
be plugged in or connection
may be loose.
•House fuse blown, circuit
breaker tripped, or a power
outage has occurred.
•Water supply tap is not turned
on.
❋ Check that the door is firmly
shut.Make sure plug fits tightly in wall
outlet.
Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have
it corrected by a qualified electrician.
Turn on water supply tap.
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the washer
begins to spin. The door must lock
before spin can be achieved.
Once started, the door can not be
opened for safety reasons.
Wait one or two minutes before 
opening the door to give the electric 
locking mechanism time to release.
The washing time may vary  by the
amount of laundry, water
pressure, water temperature and
other using conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall  be increased.
Symptom Possible Cause Solution
T
  
						

							57
roubleshooting guide
Symptom Possible Cause Solution
•Water supply is not adequate in
area
•Water supply taps are not
completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are
clogged.
• If water leakage occurred in the inlet hose,
indicator “H%” will be changed red color. 
• Drain hose is kinked or clogged.
• The drain filter is clogged.
• Load is too small.
• Load is out of balance.
•The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether. 
•If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Is the door opened or not
completely closed?
• Water overfills due to the faulty water
valve.
• Water level sensor has malfunctioned.
• Over load in motor.
• Water leaks
• The washer experienced a power failure.Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information, 
please refer to “The drain pump filter” 
on page52  
Add 1 or 2 similar items to help 
balance the load.
Rearrange load to allow proper 
spinning
Close the door completely.
❋ If  “       ”is not released, call for service.
Unplug the power plug and call for service.
Close the water tap.
Unplug the power plug.
Call for service.
Call for service.
Restart the cycle.

T
  
						

							58
erms of Warranty
What Is Not Covered:
• Service trips to your home to teach you how to use the product. 
• If the product is connected to any voltage other than that shown on the rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use in accordance
with the owners manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
• Correcting the installation for example, levelling the product, adjustment of drain.
• Normal maintenance which recommended by the owners manual.
• Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace fuses in or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs. 
• Incidental or consequential damage to personal property caused by possible defects
with this appliance.
• If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training 
center, dormitory)
If the product is installed outside the normal service area, any cost of 
transportation involved in the repair of the product, or the replacement of a 
defective part, shall be borne by the owner.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol  is attached to a
product it means the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.   
4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.  
T