LG Flatron M2362dp Owners Manual

11
PREPARATION
WALL MOUNT : HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop....

12
PREPARATION
PREPARATION
DESKTOP PEDESTAL INSTALLATION
POSITIONING YOUR DISPLAY
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
 ■The image shown may be somewhat different from your set.
 ■The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
* Tilt range
-5°15°
10 cm
10 cm
10 cm10 cm
 

13
PREPARATION
LOCATION
 ■When  adjusting  the  angle  of  the  screen,  do  not  put  your 
finger(s) in between the head of the monitor and the stand 
body. 
    You can hurt your finger(s).
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken  not to 
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a 
position to allow a free flow of air. Do not cover the ventilation openings on the back...

14
PREPARATION
PREPARATION
SECURING THE SET TO THE WALL TO PREVENT FALLING 
WHEN THE SET IS USED ON A STAND (Only M2762DP)
 ■The image shown may be somewhat different from your set.
 ■Use  a  sturdy  rope  or  cord  (sold  separately)  to  tie  the  product.  It  is 
safer  to  tie  the  rope  so  it  becomes  horizontal  between  the  wall  and 
the product.
We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the set be...

15
PREPARATION
WARNING
 ■The image shown may be somewhat different from your set.
The SET must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product. Use only an attached screw.
1-Screw
(provided as parts of the product)
Stand
Desk
 ►To prevent SET from falling over the SET should be securely attached to the floor/wall per installation 
instructions. Tipping,shaking, or rocking the machine may cause injury.
ATTACHING THE TV TO A...

16
PREPARATION
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the 
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided 
with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington 
company.  Kensington  sells  security  systems  for...

17
EXTERNAL  EQUIPMENT  SETUP
ANTENNA CONNECTION
 ■To prevent damage do not connect to the mains outlet until all connections are made between the devices.
 ■For optimum picture quality, adjust antenna direction.
 ■An antenna cable and converter are not supplied.
Multi-family Dwellings / Apartments
(Connect to wall antenna socket)Wall
Antenna
Socket
Outdoor
AntennaSingle-family Dwellings / Houses
(Connect to wall jack for outdoor antenna)
RF Coaxial Wire (75 Ω)
 ■In poor signal areas, to get better...

18
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
HD RECEIVER SETUP
Connecting with a component cable
 ■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
 ■The image shown may be somewhat different from your set.
 ►HDMI Audio Supported format : Dolby Digital, PCM 
 ►DTS Audio format is not supported.
SignalComponentHDMI
480i / 576iYESNo
480p / 576pYESYES
720p / 1080iYESYES
1080pYES
(50 Hz / 60Hz only)
YES
(24 Hz / 30 Hz / 50Hz / 60Hz)...

19
EXTERNAL  EQUIPMENT  SETUP
Connecting a set-top box with a HDMI cable
Connect  the  digital  set-top  box  to HDMI/DVI  IN   jack 
on the SET
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select HDMI input source using the INPUT button on 
the remote control.
1
2
3
NOTE
 ►Check  that  your  HDMI  cable  is  High  Speed  HDMI  Cable.  If  the  HDMI  cables  are  not  High  Speed 
HDMI Cable, flickering or no screen display can result. Please use the High...

20
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
Connect the digital set-top box to HDMI/DVI IN jack on the SET.
Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the SET.
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select HDMI input source using the INPUT button on the remote control.
Connecting with an HDMI to DVI cable
1
2
3
4
1
2