LG Flatron M2250d Owners Manual

							ENGLISH
21USING THE MONITOR SET
Adjusting the sound
Selecting an sound mode
Play	the	sound	in	its	optimized	settings	by	
selecting	one	of	the	preset	sound	modes.
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons	to	scroll	to	
AUDIO	and	press	OK.
3	 Press	the 	Navigation 	buttons 	to 	scroll 	to 	Sound 
Mode	and	press	OK.
4	 Press	the	Navigation	buttons 	to	scroll	to	a	
sound	mode	you	want	and	press	OK.
ModeDescription
StandardSelects	when	you	want	standard-quality	sound.
MusicSelects	when	you	listen	to	music.
CinemaSelects	when	you	watch	movies.
SportSelects	when	you	watch	sports	events.
GameSelects	when	you	play	games.
5	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
Customizing sound options
Customize	options	of	each	sound	mode	for	the	
best	sound	quality.
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons	to	scroll	to	
AUDIO	and	press	OK.
3	 Press	the 	Navigation 	buttons 	to 	scroll 	to 	Sound 
Mode	and	press	OK.
4	 Press	the	Navigation	buttons 	to	scroll	to	a	
sound	mode	you	want	and	press	OK.
5	 Select	and	adjust	following	options,	and	then	
press	OK.
OptionDescription
Surround XThis	option	enhances	sound	depth	and	clarity	by	maximizing	the	Surround	effect.
TrebleControls	the	dominant	sounds	in	the	output.	When	you	turn	up	the	treble,	it	will	increase	the	output	to	the	higher	frequency	range.
BassControls	the	softer	sounds	in	the	output.	When	you	turn	up	the	bass,	it	will	increase	the	output	to	the	lower	frequency	range.
ResetResets	the	sound	mode	to	the	default	setting.
6	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
yyYou	cannot	adjust	Treble	and	Bass	in	the	
RGB-PC	/	HDMI-PC	mode.
NOTE
  
						

							ENGLISH
22WATCHING TV
WATCHING TV
Connecting an antenna or 
cable
Connect	an	antenna,	cable,	or	cable	box	to	watch	
TV	referring	to	the	following.	The	illustrations	may	
differ	from	the	actual	accessories	and	an	RF	cable	
is	optional.	
Connecting an antenna or basic 
cable
Connect	the	Monitor	set	to	a	wall	antenna	socket	
with	an	RF	cable	(75	ohm).
Connecting with a cable box
Connect	the	Monitor	set	to	a	cable	box	and	the	
cable	box	to	a	wall	antenna	socket	with	2	RF	
cables	(75	ohm).
yyUse	a	signal	splitter	to	use	more	than	2	 TVs.
yyIf	the	image	quality	is	poor,	install	a	signal	
amplifier	properly	to	improve	the	image	
quality.
yyIf	the	image	quality	is	poor	with	an	antenna	
connected,	aim	the	antenna	to	the	proper	
direction.
yyVisit	http://AntennaWeb.org	for	more	
information	about	the	antenna	and	cable	
connection.
NOTEyyMake	sure	not	to	bend	the	copper	wire	of	the	
RF	cable.
yyComplete	all	connections	instructions	
between	devices,	and	then	connect	the	
power	cord	to	the	power	outlet	to	prevent	
damages	to	your	Monitor	set.
CAUTION
Copper wire
Wall AntennaSocket
OutdoorAntenna
  
						

							ENGLISH
23WATCHING TV
Accessing the TV for the 
first time
When	you	access	the	Monitor	set	for	the	first	
time,	the	initial	setting	screen	appears.	Select	a	
language	and	customize	the	basic	settings.
1	 Connect	the	power	cord	to	a	power	outlet.
2	 Press			on	the	Monitor	set	to	turn	the	
Monitor	set	on.
The	Power	indicator	lighting	is	turned	on.
yyYou	can	also	switch	the	Monitor	set	from	
PC	mode	to	TV	mode,	press	TV/PC.
yyYou	can	also	access	Initial Setting	by	
accessing	OPTION in	the	main	menus.
yyIf	you	do	not	operate	the	Monitor	set	
within	40	seconds	when	the	setting	menu	
screen	appears,	the	setting	menus	will	
disappear.
NOTE
NOTE
NOTE
NOTE
When	the	Monitor	set	is	in	Power	saving	
mode,	the	Power	indicator	lighting	blinks.
yyTo	display	images	in	the	best	quality	for	
your	home	environment,	select	Home 
Use mode.
yyStore	Demo	mode	is	suitable	for	the	retail	
environment.	
yyIf	you	select	Store Demo mode,	the	
previously	customized	settings	will	switch	
to	the	default	settings	of	Store Demo 
mode	in	2	minutes.	
If	you	do	not	complete	the	initial	setting,	it	
will	appear	whenever	you	access	the	 TV.
3	The	initial	setting	screen	appears	if	you	access	
the	TV	for	the	first	time.
4	 Follow	the	on-screen	instructions	to	customize	
your	Monitor	set	according	to	your	preferences.
Language

Mode Setting

Country

Auto Tuning
Selects	Home Use	for	the	home	environment.
Selects	a	country	to	display.
Selects	a	language	for	the	display.
Scans	and	saves	available	programmes	automatically.
5	 When	the	basic	settings	are	complete,	press	
OK.
6	 To	turn	the	Monitor	set	off,	press		on	the	
Monitor	set.	
The	Power	Indicator	turns	off.
Disconnect	the	power	cord	from	the	power	
outlet	when	you	do	not	use	the	Monitor	set	
for	a	long	period	of	time.
CAUTION
  
						

							ENGLISH
24WATCHING TV
Watching TV
1	 Press		 on	the	Remote	control	or		on	the	
Monitor	set	to	turn	the	Monitor	set	on.
2	 Press	INPUT	and	select	Antenna.
3	 Control	the	Monitor	set	using	the	following	
buttons	and	menus	while	you	are	watching	 TV.
Button / MenuDescription
P() orPR (	 )  Scrolls	through	the	saved	programmes
NumbersSelects	a	programme	by	entering	numbers
 (+ , -)	orVOL (	 )Adjusts	the	volume	level
MUTEMutes	all	sounds
PICTURESelects	one 	of 	the 	preset 	image	modes	(See	p.60)
AUDIOSelects	one	of	the	preset	audio	modes.	(See	p.63)
RATIO (Except	3D	Model)Resizes	an	image	(See	p.34)
4	 To	turn	the	Monitor	set	off,	Press	 on	the	
Remote	control	or		on	the	Monitor	set.
Managing programmes
Automatically setting up 
programmes
For countries other than Finland, Sweden, 
Denmark and Norway)
Use 	this 	to 	automatically 	find 	and 	store 	all 	available	
programmes.
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Auto Tuning	and	press	OK.
4	 Select	Start	to	start	automatic	tuning.
The	TV 	scans 	and 	saves 	available 	programmes	
automatically.
5	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock System ‘On’.
yyAutomatic	Numbering:	Decide	whether	to	
use	the	programme	numbers	as	sent	by	
broadcasting	stations	for	tuning.
yyWhen	select	Italy	in	the	Country	menu,	if	
the	pop	up	is	displayed	when	the	conflicted	
Programme	after	Auto	Tuning,	select	a	
broadcaster	for	conflicting	programme	
number	to	solve.
  
						

							ENGLISH
25WATCHING TV
Only for Finland, Sweden, Denmark and Norway
DVB-C	Auto	Tuning	is	a	menu	for	users	in	
countries	that	support	DVB	cable.
yyIf	you	want	to	select	the	Antenna
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Auto Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	
Antenna	and	press	OK.
5	 Select	Start	to	start	automatic	tuning.
The	TV 	scans 	and 	saves 	available 	programmes	
automatically.
6	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock System ‘On’.
yyAutomatic	Numbering:	Decide	whether	to	
use	the	programme	numbers	as	sent	by	
broadcasting	stations	for	tuning.NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock System ‘On’.
yyAutomatic	Numbering:	Decide	whether	to	
use	the	programme	numbers	as	sent	by	
broadcasting	stations	for	tuning.
yyIf	you	want	to	select	the	Cable
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Auto Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	
Cable	and	press	OK.
5	 Press	the	Navigation	buttons	to	scroll	to	
Comhem or Other Operators	and	press	OK.
6	 Press	the	Navigation	buttons	to	scroll	to	
Default, Full or User	and	press	OK.
7	 Press	the	Navigation	buttons	or	Number	
buttons	to	scroll	make	appropriate	adjustments	
(Except	for	Full	mode)	and	press	OK.
8	 Press	the	Navigation	buttons	to	scroll	to	
Close and	press	OK.
9	 Select	Start	to	start	automatic	tuning.
The	TV 	scans 	and 	saves 	available 	programmes	
automatically.
10	When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
  
						

							ENGLISH
26WATCHING TV
To	watch	DVB-C	in	the	countries	excluding	
Finland,	Sweden,	Denmark	and	Norway	select	'-	-'	
as	the	Country	in	OPTION.	
You	can	select	User	mode	or	Full	mode	in	Auto	
Tuning.	
The	corresponding	home	frequency	information	
may	need	to	be	changed	when	tuning	the	User	
mode,	and	the	corresponding	information	depends	
on	the	Cable	Service	Operator	(SO)	in	service.	
During	Full	mode	tuning,	some	channel	may	be	
restricted	for	some	Cable	Service	Operator	(SO),	
and	it	may	take	a	long	time	for	tuning.
If you select the “- -” of Country Setting, 
(Except for Finland, Sweden, Denmark and 
Norway)
NOTE
yyYour	cable	provider	may	charge	for	their	
services,	or	require	you	to	agree	to	its	items	
and	conditions	of	business.
yyDVB-C	Cable	may	not	operate	correctly	with	
some	cable	providers.
yyCompatibility	with	DVB-C	digital	cable	
broadcasts	is	not	guaranteed.
yyWhen	you	select	the	Cable,	the	Cable	
Service Operator	selection	screen	can	differ	
or	not	exist	by	the	Cable	situation	of	the	
applicable	country.
The	popup	window	to	select	between	Service 
Operator	is	only	shown	initially	for	the	3	cases	
when	you	accessing	the	Initial Setting	menu,	
when	you	change	from	Antenna	to	Cable	or	
when	you	access	the	menu	after	changing	the	
Country.
When	you	want	to	select	between	Service 
Operator	aside	from	the	above	3	cases,	you	
can	do	so	by	selecting	SETUP		→	Cable DTV 
Setting	→	Service Operator.
yyAcquired	certification	SO:	Sweden(Comhem,	
Canal	Digital),	Denmark(YouSee,	Canal	
Digital,	Stofa),	Norway(Canal	Digital).
If	there	are	not	any	Service	Operator	that	you	
want,	select	Other Operators.
If	you	select	"Other	Operators",	or	the	selected	
country	supports	"Other	Operators"	only,	it	may	
take	some	time	to	search	all	the	channels,	or	it	
may	not	search	some	of	the	channels.
If	some	of	the	channels	do	not	appear,	follow	
the	steps	below.
1.	SETUP → Auto Tuning → Cable
2.	Input	additional	values	such	as	the	
frequency,	symbol	rate,	modulation,	and	
network	ID	(You	can	ask	your	cable	service	
provider	for	the	above	information).
yyThe	following	values	are	needed	in	order	to	
search	all	available	programmes	quickly	and	
correctly.	The	commonly	used	values	are	
provided	as	"default".	However,	for	correct	
settings,	please	inquire	of	the	cable	service	
provider.	When	running	 Auto	Tuning	in	
DVB	cable	mode,	selecting	Full	will	search	
through	all	frequencies	to	find	available	
channels.	In	the	case	when	the	programme	
is	not	searched	by	selecting	the	Default,	
perform	the	searching	by	selecting	the	Full.	
However,	in	the	case	when	the	programme	
is	searched	by	selecting	the	Full,	the	 Auto	
Tuning	time	can	be	taken	too	much.
 »Frequency:	Enter	a	user-defined	frequency	
range.
 »Symbol rate:	Enter	a	user-defined	symbol	
rate	(Symbol	rate:	Speed	at	which	a		device	
such	as	modem	sends	symbols	to	a	
channel).
 »Modulation:	Enter	a	user-defined		
modulation.	(Modulation:	Loading	of	audio	or	
video	signals	onto	carrier).
 »Network ID:	Unique	identifier	allocated	for	
each	user.
  
						

							ENGLISH
27WATCHING TV
(When selecting Cable (DVB cable mode) if 
Finland, Sweden, Denmark, Norway or “--” 
country is chosen)
NOTE
NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock	System	‘On’.
yySymbol rate:	Enter	a	user-defined	symbol	
rate.	(symbol	rate:	Speed	at	which	a	
device	such	as	modem	sends	symbols	to	a	
channel.)
yyModulation:	Enter	a	user-defiend	
modulation.(Modulation:	Loading	of	audio	or	
video	signals	onto	carrier)
yyFrequency,	Symbol	rate,	and	Modulation	
mode	are	needed	in	order	to	add	a	
programme	correctly	in	DVB	cable	mode.	
Please	inquire	of	the	cable	service	provider	
about	the	correct	values.
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock	System	‘On’.
Manually setting up programmes 
(In digital mode)
Manual	Tuning 	lets 	you 	manually 	add 	a 	programme	
to	your	programme	list.
(For countries other than Finland, Sweden, 
Denmark and Norway & When selecting 
Antenna if Finland, Sweden, Denmark, Norway 
or “--”country is chosen)
1	 Press	MENU	to	access	the	Main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Manual Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	DTV.
5	 Press	the	Navigation	buttons	or	Number	
buttons	to	scroll	Select	the	desired	channel	
number,	and	then	add	programmes.
6	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
1	 Press	MENU	to	access	the	Main	menus.
2	 Press	the	Navigation	buttons	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Manual Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	DTV.
5	 Press	the	Navigation	buttons	or	Number	
buttons	to	scroll	Select	the	desired	Frequency,	
Symbol	rate	and	Modulation,	and	then	add	
programmes.
6	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
  
						

							ENGLISH
28WATCHING TV
NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock	System	‘On’.
yyL:	SECAM	L/L	(France)
yyBG:	PAL	B/G,	SECAM	B/G	(Europe	/	East	
Europe	/	 Asia	/	New	Zealand	/	M.East	/	 Africa	
/	Australia)
yyI: PAL 	I/II	(U.K.	/	Ireland	/	HongKong	/	South	
Africa)
yyDK:	PAL 	D/K,	SECAM	D/K	(East	Europe	/	
China	/	 Africa	/	CIS)
yyTo	store 	another 	channel, 	repeat 	steps 	4 	to 	9.
Manually setting up programmes 
(In analogue mode)
Manual	 Tuning	lets	you	manually	tune	and	arrange	
the	stations	in	whatever	order	you	desire.
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Manual Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	
TV	and	press	OK.
5	 Press	the	Navigation	buttons	to	scroll	to	
System.
6	 Press	the	Navigation	buttons	to	scroll	to	
V/UHF or Cable.
7	 Press	the	Navigation	buttons	or	Number	
buttons	to	scroll	Select	the	desired	channel	
number.
8	 Press	the	Navigation	buttons	to	scroll	to	
Commence	searching.
9	 Press	the	Navigation	buttons	to	scroll	to	
Store	and	press	OK
10	When	you	are	finished,	press	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
Assigning a station name
You	can	assign	a	station	name	with	five	characters	
to	each	programme	number.
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to		
Manual Tuning	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	TV	.
5	 Press	the	Navigation	buttons	to	scroll	to	Name	
and	press	OK.
6	 Press	the	Navigation	buttons	to	scroll	to	TV 
System.
7	 Press	the	Navigation	buttons	to	scroll	to	V/UHF 
or Cable.
8	 Press	the	Navigation	buttons	to	scroll	Select	
the	position	and	make	your	choice	of	the	
second	character,	and	so	on.	You	can	use	an	
the	alphabet 	A 	to 	Z, 	the 	number 	0 	to 	9, 	+/ 	-, 	and	
blank	and	press	OK
9	 Press	the	Navigation	buttons 	to	scroll	to	Close	
and	press	OK.
10	Press	the	Navigation	buttons	to	scroll	to	Store	
and	press	OK
11	When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
  
						

							ENGLISH
29WATCHING TV
Editing your programme list
1	 Press	MENU	to	access	the	main	menus.
2	 Press	the	Navigation	buttons	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	
Programme Edit	and	press	OK.
4	 Edit	programmes	using	the	following	buttons.
ButtonDescription
Highlights	the	programme	type
NavigationScrolls	through	programme	types	or	programmes
OKSelects	a	programme	to	view
P ()Moves	to	the	previous	or	next	page
NOTE
yyUse	Number	buttons	to	input	a	4-digit	
password	in	Lock	System	‘On’.
NOTE
yyIf	you	select	Cable,	you	can	see	Cable	DTV	
Setting	menu.
yyWhen	Channel	Auto	Update	is	On,	the	
channel	information	will	be	automatically	
updated	whenever	the	network	information	
changes.
yyWhen	Channel	Auto	Update	is	Off,	the	
channel	information	will	not	be	updated.
Cable DTV Setting (In Cable 
mode only)
The	range	that	a	user	can	select	from	the	Service	
Operator	menu	differs	depending	on	number	of	
Service	Operator	supported	by	each	country,	and	
if	number	of	supported	Service	Operator	for	each	
country	is	1,	corresponding	function	becomes	non-
activation.
After	changing	Service	Operator,	a	warning	
window	saying	that	channel	map	will	be	deleted	
when	OK	button	is	pressed	or	Close	is	selected,	
and	a	Auto-tuning	pop-up	window	appears	when	
'YES'	is	selected.
SETUPMoveOK
Auto TuningManual TuningProgramme EditSoftware Update    : OnDiagnosticsCI InformationCable DTV Setting                        ꔉ
1	 Press	MENU	to	access	the	Main	menus.
2	 Press	the	Navigation	buttons 	to	scroll	to	
SETUP	and	press	OK.
3	 Press	the	Navigation	buttons	to	scroll	to	Cable 
DTV Setting	and	press	OK.
4	 Press	the	Navigation	buttons	to	scroll	to	
Service Operator or Channel Auto update	
and	press	OK.
5	 When	you	are	finished,	press 	EXIT.
When	you	return	to	the	previous	menu,	press	
BACK.
  
						

							ENGLISH
30WATCHING TV
In TV mode
1		 Press	the	Navigation	buttons,	scroll	to	the	
programme	number	you	wish	to	delete.
2		 Press	the	Red	button	to	delete	the	selected	
programme	number.
3		 Press	the	Blue	button	to	release.
1		 Press	the	Navigation	buttons,	scroll	to	the	
programme	number	you	wish	to	move.
2		 Press	the	Green	button	with	the	programme	
number	selected,	you	wish	to	move.
3		 Press	the	navigation	buttons,	move	to	where	
you	wish	to	place	the	programme	number,	and	
then	press	the	Green	button	again.
1	 Press	the	Yellow	button	to	start	Auto	Sort.
NOTE
NOTE
yyThe	selected	programme	is	deleted,	all	the	
following	programmes	are	shifted	up	one.
yyAfter	activating	 Auto	Sort	once,	you	can	no	
longer	edit	programmes.
Deleting a programme
Moving a programme
Auto Sort
1		 Press	the	Navigation	buttons,	scroll	to	the	
programme	number	you	wish	to	skip.
2		 Press	the	Blue	button	to	skip	the	selected	
programme	number.
3		 Press	the	Blue	button	again	to	release.
Skipping a programme number
NOTE
yyYou	will	be	unable	to	select	a	skipped	
programme	using	P () buttons	during	
watching	TV.
yyIf	you	wish	to	watch	a	skipped	programme,	
directly	enter	the	programme	number	
using	number	buttons	or	release	it	in	the	
Programme Edit	menu	or	EPG.
In DTV/RADIO mode
1		 Press	the	Navigation	buttons,	scroll	to	the	
programme	number	you	wish	to	skip.
2		 Press	the	Blue	button	to	skip	the	selected	
programme	number.
3		 Press	the	Blue	button	again	 to	release.
NOTE
yyThe	skipped	programmes	are	shown	in	
blue	on	the	programme	list	and	these	
programmes	will	not	appear	on	the	screen	
when	changing	programmes	using	P()	
buttons	during	watching	 TV.
yyIf	you	wish	to	watch	a	skipped	programme,	
directly	enter	the	programme	number	
using	number	buttons	or	release	it	in	the	
Programme	Edit	menu	or	EPG.
Skipping a programme number