LG Flatron L245wp Users Guide

							Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
L245WP
L245WPM
User’s Guide
 
						

							A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside. 
There are Dangerous High Voltages inside, even when the power is OFF. 
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the displays cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Important Precautions
 
						

							A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance. 
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
 
						

							Connecting the Display
A3
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand base or Removing the stand base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2.Rotate the Stand Body as shown in figure      .
The tape and locking pin may only be removed from those monitors equipped
with a standing base when the base is pulled up.
Otherwise, you may be injured by the protruding sections of the stand.Warning :
1
3.Align the hooks on the Stand Body with the matching slots in the Stand Base.
4. Insert the hooks into slots.
Slot
Hook
Stand Base
 
						

							A4
Connecting the Display
ImportantThis illustration depicts the general model of connection. Your monitor \
may differ from 
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The pr\
oduct may
fall and get damaged or injure your foot.
5.Attach the monitor to the Stand Base by turning the screw to the right. \
  
Screw : Turn the screw by using the screw handle.
6.Lift and turn the monitor to face towards the front after the connection\
 is 
made to the female part of the cable youre attaching.
7.Take the screw out by turning to the left to separate the monitor and St\
and Base.
 
						

							A5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the\
 computer 
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚~20˚                             Swivel :350˚
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable\
 viewing position,  
the forward tilt angle of the monitor should not exceed 5 degrees.
Slightly wipe stained spot on the exterior only with the cleansing cloth\
s for the product exterior if there 
is stain or fingerprint on surface of the exterior. Do not wipe roughly \
when removing stain. Please be 
cautious of that excessive power may cause scratch or discoloration. 
Height Range : maximum 3.94 inch (100.0mm)
100.0mm
* Please be sure to       remove the Locking  
pin to adjust the height.   
You do not need to replace the Locking pin  after it is removed,  to adj\
ust its height. Notice
 
						

							A6
Connecting the Display
1.Lift the monitor to its highest height to utilize the Pivot function.
2.Landscape & Portrait : You can rotate the panel 90o  clockwise. 
Please be cautious and avoid contact between the monitor head and the St\
and 
Base when rotating the screen to access the Pivot function. If the monit\
or head  
touches the Stand Base, then the Stand Base could crack.
3.For detailed information, please refer to the Pivot Software CD provided\
.
Using the Pivot function
Stand sectionHead section
 
						

							A7
Connecting  the speakers - The feature is only for speaker models - L245WPM
Connecting the speaker
1.Rotate the panel at an angle of 90 degrees as shown in the picture, after lifting 
the monitor to its highest height.
* Make sure the panel does not 
touch the floor when rotating.
2. Insert the projecting hook of the speaker in the direction of the monitor’s back
slot until you hear the clicking sound.  
3. After connecting the speaker, connect the Audio DC-IN cable to the DC-OUT 
socket on the back of the monitor.
4. Connect the audio cable to the AUDIO-IN terminal. When using HDMI, you can
connect the monitor’s to the AUDIO-OUT terminal. When using a PC or other
component, simply connect to the appropriate female socket of the external
instrument.
DC-OUT HDMI/DVICOMPONENT
AUD IO
OUT
D-SUBYPRPB   1                          2
DC-OUT HDMI/DVICOMPONENT
AUDIO
OUT
D
-
S
U
BYPRPB
   1                          21
DC-OUT HDMI/DVICOMPONENT
AUDI O
OUT
D
-
S
U
BYPRPB
   1                          2
DC-OUT HDMI/DVICOMPONENT
AUDIO
OUT
D
-
S
U
BYPRPB
   1                          2Hook
Audio DC-In
Cable
SlotAUDIO  In
DC-OUT HDMI/DVICOMPONENT
AUDIO
OUT
D
-
S
U
B
YP
RPB
   1                          22
3
DC-OUT
Be cautious to avoid your hand being caught 
between the speaker and Stand Base when lowering 
the monitor  to its lowest height, with the speaker 
fully equipped. 
Notice
 
						

							A8
Name and function of the Parts 
Rear View
DC-OUT HDMI/DVICOMPONENT
AUDIO
OUT
D-SUBYPRPBAC-IN
   1                          2
6
8
2
9
3451
7
AC-IN Connector : Connect the Power Cord     DC-OUT Jack 
HDMI/DVI  Signal Connector                                                            COMPONENT Input Terminal
D-SUB Analogue Signal Connector    
Kensington Security Slot
USB UP stream Port(1EA)
USB DOWN stream Port(2EA)
Audio out Jack(
Headset/Earphone/connecting terminal of the Speaker) 
12
34
5
7
8
6
9
AUDIO
OUT
U
B
   1                          2AUDIO
OUT
The Left Rear of the Monitor
: You can use the AUDIO-OUT Jack by connecting earphones or a headset
when using the HDMI configuration..*AUDIO-OUT is only available with the HDMI input.
(You cannot use it with D-SUB, DVI or any other component.) 
 
						

							A9
Connecting to External Devices
1.Place the monitor in a convenient, well-ventilated location near your co\
mputer.  
To adjust height of your monitor, unlock the stand lock on top of the st\
and.
2.Connect the signal cable. When attached, tighten the thumbscrews to secure the
connection. 
3.Connect the power cord into a proper power outlet  that is easily access\
ible and close      
to the display.
Wall-outlet type
4.Press        button on the front switch panel to turn the power on.
5.Press theINPUTbutton at the front side of the monitor.
NOTE  This is a simplified representation
of the rear view. 
This rear view represents a
general model; your display may
differ from the view as shown.
1
2
PC MAC
Mac adapterFor Apple Macintosh use, a  separate plug adapter is needed to change th\
e 15 pin 
high density (3 row) D-sub VGA connector on the supplied cable to a 15\
 pin  2 row
connector.
2DC-OUT HDMI/DVI COMPONENT
AUDIO
OUT
D -S
U BY PRPB   1                          2
Power CordSignal Cable
Varies according to model.
INPUTOK/AUTO
When connecting with a HDMI/DVI signal input cable.• Select 
HDMI : HDMI/DVI digital signal.
When connecting with a D-Sub signal cable.• Select  RGB: D-Sub analogue signal.B
A
When Connecting to your PC
NoteHow to connect to two computers.
Connect the signal cables (HDMI/DVI and D-Sub) to each computer. 
Press the INPUT button at the front side of the monitor.
Directly connect to a grounded power outlet on the wall or 
a power bar with a ground wire.
1
INPUT
RGB 
HDMI
Component