LG Flatron L1972h Users Guide

Make sure to read the Important Precautionsbefore using this product. 
Keep the User's Guide (CD) in an accessible place for future reference.
See the attached label on the unit and show this information to your dealer
when  asking for service.
L1972H
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which...

Connecting the Display
A3
Unfolding the stand base
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off. 
1.Place the monitor with its front facing downward on a soft cloth.
2.Hold the stand base and lift it up following the sequence as shown in the
picture.
3.Pull the stand base down at the same spot shown in the picture, and
the stand will be unfolded.
4.Place the monitor upright and adjust the stand
base to the desired...

A4
Connecting the Display
1.Face the front of the monitor dislpay. Than gently push the monitor backwards,
following the sequence shown in the picture below. 
Folding the stand base
Tilt range 
1.Make sure that the angle of the panel is set for your comfort. 
Tilt Range: 0˚~30     
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees
Rownloaded'from'≤anual≤onitor4com'≤anuals 

Connecting the Display
A5
To adjust the height
Scope of adjusting the height  : maximum 4.02 inches (102 mm)
102 mm
Rownloaded'from'≤anual≤onitor4com'≤anuals 

A6
Connecting the Display
2
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as below sketch map
form to .
Wall-outlet type
MAC
Power Cord12
Mac adapterFor Apple Macintosh use, a  separate plug adapter is needed
to change the 15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin  2 row connector.
2.Press        button on the side switch panel to turn the
power on. When monitor power is turned on, the 
Self Image Setting Function is...

A7
Connecting the Display
To arrange the cables
1.Insert  and  screw  the  cable  holder  into  the  hole  in  the  back  of  the  stand  until  it  will  not
turn any more as shown in the following figure.
Cable Holder
2.After connecting the cables neatly, arrange the cables to the Cable Holder as shown in 
the following figure.
Rownloaded'from'≤anual≤onitor4com'≤anuals 

6
A8
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU buttonfor several
seconds. The message "OSD LOCKED"appears.
You can unlock the OSD settings at any time by pushing the
MENU buttonfor several seconds. The message "OSD
UNLOCKED"appears....

A9
Control Panel Functions
This Indicator lights up as blue when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color will
changes to amber.Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to selection an icon in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton prior to entering the On
Screen Display(OSD). This will...