LG Flatron L1972h Users Guide

							Make sure to read the Important Precautionsbefore using this product. 
Keep the User's Guide (CD) in an accessible place for future reference.
See the attached label on the unit and show this information to your dealer
when  asking for service.
L1972H
User’s Guide
 
						

							A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside. 
There are Dangerous High Voltages inside, even when the power is OFF. 
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not drop an object on or apply impact to the product. Do not throw any toys
or objects on the product screen. 
It can cause injury to human, problem to product and damage the display.  
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the displays cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
When the display is to be left unattended for an extended period of time, unplug
it from the wall outlet.
In the presence of thunder and lightning, never touch the power cord and signal
cable because it can be very dangerous. It can cause electric shock. 
Important Precautions
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Main power breaker is the power cord and this breaking device must be located at
a location where it is easy to operate.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance. 
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
 
						

							Connecting the Display
A3
Unfolding the stand base
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off. 
1.Place the monitor with its front facing downward on a soft cloth.
2.Hold the stand base and lift it up following the sequence as shown in the
picture.
3.Pull the stand base down at the same spot shown in the picture, and
the stand will be unfolded.
4.Place the monitor upright and adjust the stand
base to the desired angle. Adjust the stand 
base's angle by holding the edges of the monitor 
gently with both hands.
Important
This illustration depicts the typical connection procedure. Your monitor 
may differ from the one displayed in the pictures above.
Do not touch or apply force to the monitor's screen while expanding or folding
the stand base.
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							A4
Connecting the Display
1.Face the front of the monitor dislpay. Than gently push the monitor backwards,
following the sequence shown in the picture below. 
Folding the stand base
Tilt range 
1.Make sure that the angle of the panel is set for your comfort. 
Tilt Range: 0˚~30     
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							Connecting the Display
A5
To adjust the height
Scope of adjusting the height  : maximum 4.02 inches (102 mm)
102 mm
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							A6
Connecting the Display
2
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as below sketch map
form to .
Wall-outlet type
MAC
Power Cord12
Mac adapterFor Apple Macintosh use, a  separate plug adapter is needed
to change the 15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin  2 row connector.
2.Press        button on the side switch panel to turn the
power on. When monitor power is turned on, the 
Self Image Setting Function is executed automatically.
(Only Analog Mode)
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals. 
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted
screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve
resolution. 
NOTE  This is a simplified representation of the rear
view.
This rear view represents a general model;
your display may differ from the view as
shown.
PC
1
PC
Varies according to model.
Signal Cable
A
B
C
Connect DVI Cable
Connect Dsub Cable (PC)
Connect Dsub Cable (Mac)
DVI-D(This feature is not 
available in all countries.)
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							A7
Connecting the Display
To arrange the cables
1.Insert  and  screw  the  cable  holder  into  the  hole  in  the  back  of  the  stand  until  it  will  not
turn any more as shown in the following figure.
Cable Holder
2.After connecting the cables neatly, arrange the cables to the Cable Holder as shown in 
the following figure.
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							6
A8
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU buttonfor several
seconds. The message "OSD LOCKED"appears.
You can unlock the OSD settings at any time by pushing the
MENU buttonfor several seconds. The message "OSD
UNLOCKED"appears.
Front Panel Controls
Bottom
ZOOMINGAt the current display, Use 'ez Zooming' Key, then the display resolution
is transferred to the one step low resolution.
Use 'ez Zooming' Key one more, the display is back to the
original display.
Those with poor eyesight such as the elderly, those who have
difficulty using computers and children can enlarge text or
pictures by adjusting resolution with a single touch. 
The resolutions at which the EZ ZOOMING operates are as follows:
1280 x 1024, 1024 x 768, 800 x 600. 
The setting method can differ by O/S or video card. In this case, Please ask to the computer or the video
card manufacturer.
To use this feature, please install forteManager program in the enclosed CD-ROM.
Rownloaded'from'≤anual≤onitor4com'≤anuals 
						

							A9
Control Panel Functions
This Indicator lights up as blue when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color will
changes to amber.Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to selection an icon in the On Screen 
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton prior to entering the On
Screen Display(OSD). This will automatically adjust
your display image to the ideal settings for the
current screen resolution size (display mode).
The best display mode is
1280 x 1024
Control Function
-  + ButtonsUse these buttons to select or adjust functions in the
On Screen Display.
For more information, refer to page A15.
Use this button to make either D-Sub or DVI
connector active. This feature is used when two
computers are connected to the display. The default
setting is D-Sub.+ Button(SOURCE Hot key)
- Button(                   )
3ownloadedWfromWManualMonitorUcomWManuals