LG Flatron L194ws Users Guide

Make sure to read the Important Precautions before using the product. 
Keep the User's Guide(CD) in an accessible place for furture reference\
.
See the label attached on the product and give the information to your
dealer when you ask for service.
L194WS
L204WS
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another \
power
cord, make sure that it is certified by the applicable national standard\
s if not being...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do n\
ot place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kit\
chen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow \
the release of
heat generated during operation. If these openings are blocked, built-up\
 heat can
cause failures...

A3
Connecting the Display
ImportantThis illustration depicts the general model of connection. Your monitor \
may differ from
the items shown in the picture.
Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The pr\
oduct may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the\
 computer
system, and other attached devices is turned off.
Connecting the stand 
1. 
Place...

A4
Connecting the Display
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 

2. Place the monitor face down on
the cushion or soft cloth.     

3.Hold the product as it follows and lift up the Stand slightly.

4.Change your hold on the product as it follows and turn the Stand Base in\
 the arrow
direction.
5.Pull out the Stand to remove.

The Head part
The Stand 
base part
 

A5
Connecting the Display
To remove the Stand Base: 2.
Hold the body of the Stand as it follows.
Type. A

3.Press inside the two long latches at thesame time with your strength as it follows.
5.The body of the Stand and the Stand Base are successfully separated.

4.Keep pressing the two latches and use the otherhand to hold the body of the Stand to push the
Stand Base in the arrow direction to remove.

1.Ensure there are two short and two long
latches at the bottom of the Stand Base.
 

A6
Connecting the Display
To remove the Stand Base: 2. 
Hold the body of the Stand as it follows.
Type. B

3.Press inside the four latches individually toward each end.
4.Put the Stand Base on a flat surface and pullup the body of the Stand while holding the
Stand Base with the other hand. to remove.
5.The body of the Stand and the StandBase are successfully separated.

1.Ensure there are four latches at the
bottom of the Stand Base.
 

A7
Connecting the Display

20

Before setting up the monitor, ensure that the power to the monitor, the\
 computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.Tilt Range :  -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable\
 viewing
position, the forward tilt angle of the monitor should not exceed 5 degr\
ees.

When adjusting the...

A8
2
1
Connecting the Display
Using the Computer
1.Place the monitor in a convenient, well-ventilated location near your co\
mputer. 2.Connect the signal cable. When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cord into a proper power outlet  that is easily access\
ible and close to
the display.




Wall-outlet type
PC-outlet type
MAC PC
Power Cord
Signal CableAnalog signalD-sub
Varies according to model.
1
2
Mac adapterFor Apple Macintosh use, a  separate plug...

A9
Control Panel Functions
MENU ButtonUse this button to enter or exit the On Screen Display.

Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message  "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the  MENU button for several seconds. The message
"OSD UNLOCKED" should appear.

ButtonsUse these...