Lexmark X940e Owners Manual

Diagnostic aids3-11
7510
Go Back Previous
Next
•Single—Feeds one sheet of media from the selected source.
•Continuous—Media continues feeding from the selected input source until Stop  is pressed.
Sensor Test (input tray)
This test is used to verify that a specific input tray’s sensors are working correctly. 
To run the Input Tray Sensor Test:
1. Touch INPUT TRAY TESTS from the Diagnostics Menu.
2. Touch Sensor Test.
After selecting Sensor Test, the LCD displays each installed input source, one source...

3-12Service Manual 7510
Go Back Previous
Next
•Continuous—Media continues feeding from the selected source until Stop  is pressed.
Press Stop  to return to the [Selected Output Bin].
While this test runs, [Selected Output Bin] Feeding...appears on the LCD. During Single tests, no buttons 
are active. However, during Continuous tests, you can press Stop  to cancel the test.
Feed To All Bins
This test can be used to verify that the printer can feed media to the standard bin or any installed output options....

Diagnostic aids3-13
7510
Go Back Previous
Next
Hole Punch Test
This test is used to verify that media can be fed to a finisher output bin and then hole punched. No information is 
printed on the feed test pages. 
To run the Hole Punch Test:
1. Touch FINISHER TESTS from the Diagnostics Menu.
2. Touch Hole Punch Test.
3. Touch 3 Punch Test.
Eight sheets of paper are fed, and then the pages are hole-punched with a 2-hole or 3-hole pattern depending 
on the selected punch test. Media is initially requested...

3-14Service Manual 7510
Go Back Previous
Next
Available Bin Level Sensors
Available Media Path 1 Sensors
Available Media Path 2 Sensors
Available Booklet Path Sensors Sensor Name
Finisher upper media bin full
Stacker bin level1
Stacker bin level2
Stacker bin upper limit
Stacker bin no media
Stacker bin level encod
 Sensor Name
Bridge unit media entrance
Bridge unit media exit
Finisher media entrance
Bridge unit media bin exit
Buffer path
Upper media exit
Lower media exit
Compiler media in
De-curler cam...

Diagnostic aids3-15
7510
Go Back Previous
Next
Available Punch and Staple Sensors
After selecting one of the available sensors, you can manually toggle the sensor between its two values (Open 
or Closed). The LCD displays Open when the sensor is open, and Closed when the sensor is closed.
Press Stop   to exit the test.
BASE SENSOR TEST
This test verifies that the sensors in the base machine are operating properly. 
To run the Base Sensor Test:
Touch BASE SENSOR TEST from the Diagnostics Menu. The panel...

3-16Service Manual 7510
Go Back Previous
Next
Devices Sensors
Exit Level Sensor
Media Path Sensors
Transfer Belt Sensors
To test any of the displayed sensors, you must manipulate the appropriate area of the printer so the sensor’s 
value will toggle to Open or Closed.
If the panel inaccurately displays the sensor’s status, then the sensor must be malfunctioning.
Press Stop   to cancel the test. 
DEVICE TESTS
Quick Disk Test
This test will perform a non-destructive read/write on one block per track on the...

Diagnostic aids3-17
7510
Go Back Previous
Next
Quick Disk Test Testing... appears on the LCD. This test cannot be canceled. After the test finishes, either 
Quick Disk Test Passed or Quick Disk Test Failed appears on the LCD. This message remains until you 
touch Back.
Disk Test/Clean
This test performs a low-level format of the hard disk.
Warning:  This test destroys all data on the disk and should never be performed on a good disk. Use this test 
only when the disk contains bad data and is unusable....

3-18Service Manual 7510
Go Back Previous
Next
PRINTER SETUP
To enter the PRINTER SETUP screen, touch PRINTER SETUP from the Diagnostics Menu. The following 
graphic appears on the LCD:
Defaults
The value of this setting determines whether the printer uses the US or Non-US factory default value for the 
printer settings listed below:
Touch Submit to change the value of this setting, then the LCD returns to the Diagnostics menu. To return to 
the PRINTER SETUP menu without changing the value of this...

Diagnostic aids3-19
7510
Go Back Previous
Next
Printed Mono Page Count
The value of this setting enables you to gauge the amount of usage on a device. 
The Printed Page Count cannot be reset by the servicer.
Permanent Page Count
The value of this setting indicates the total number of pages that have been printed by the printer. 
The Permanent Page Count cannot be reset.
Serial Number
This printer setting records the printer’s serial number that was assigned by the manufacturer. When you select 
this...

3-20Service Manual 7510
Go Back Previous
Next
The Configuration ID setting allows you to set both Configuration IDs simultaneously. To set one or both 
Configuration IDs:
1. From the PRINTER SETUP menu, touch the icon to the right of the Configuration ID menu item. The 
screen displays the value of both Configuration IDs. By default, the cursor appears on the Configuration 
ID 1 line.
2. To change the value of Configuration ID 1, touch the Backspace key to erase any of the existing 
characters. Then...