Lexmark X864de User Manual

NetWare menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > NetWare
Menu itemDescription
Activate
Yes
NoActivates NetWare support
Note: No is the factory default setting.
View Login NameLets you view the assigned NetWare login name
Note: This can be changed only from the Embedded Web Server.
Print ModeLets you view the assigned NetWare print mode
Note: This can be changed only from the Embedded Web Server.
Network...

Menu itemDescription
Primary SMTP Gateway
Primary SMTP Gateway Port
Secondary SMTP Gateway
Secondary SMTP Gateway PortSpecifies SMTP server port information
Note: 25 is the default SMTP gateway port.
SMTP Timeout
5–30Specifies the amount of time in seconds before the server stops trying to
send the e‑mail
Note: 30 seconds is the factory default setting.
Reply Address
Use SSL
Disabled
Negotiate
RequiredSpecifies server information. This is a required item.
Notes:
The message box has a limitation of 512...

Security menu
Miscellaneous menu
Menu itemDescription
Panel Logins
Login failures
Failure time frame
Lockout time
Panel Login Timeout
Remote Login TimeoutLimits the number and time frames of failed login attempts from the printer control
panel before all users are locked out
Notes:
“Login failures” specifies the number of failed login attempts before users are
locked out. Settings range from 1–50. 3 attempts is the factory default setting.
“Failure time frame” specifies the time frame during which failed...

Menu itemDescription
Job Expiration
Off
1 hour
4 hours
24 hours
1 weekLimits the amount of time a confidential job stays in the printer before it is deleted
Notes:
Off is the default setting.
If the Job Expiration setting is changed while confidential jobs reside on the
printer RAM or printer hard disk, the expiration time for those print jobs does
not change to the new default value.
If the printer is turned off, all confidential jobs held in printer RAM are
deleted.
Disk Wiping menu
Menu...

Menu itemDescription
Scheduled Method
Single pass
Multiple passDisk Wiping erases only print job data that is not currently in use by the file system
from the printer hard disk. All permanent data on the printer hard disk is preserved,
such as downloaded fonts, macros, and held jobs.
Both manual and scheduled wiping allow the file system to reuse marked disk space
without first having to wipe it.
Notes:
This menu item appears only if a formatted, non-defective printer hard disk is
installed.
Single pass...

Menu itemDescription
Automatically Observe DST
On
OffNote: On is the factory default setting and uses the applicable Daylight Saving Time
associated with the Time Zone setting.
Custom Time Zone SetupSet up your time zone.
Enable NTP
On
OffEnables Network Time Protocol, which synchronizes the clocks of devices on a
network
Note: On is the factory default setting.
Settings menu
General Settings menu
Menu itemDescription
Display Language
English
Francais
Deutsch
Italiano
Espanol
Dansk
Norsk
Nederlands...

Menu itemDescription
Eco-Mode
Off
Energy
Energy/Paper
PaperMinimizes the use of energy, paper, or specialty media
Notes:
Off is the factory default setting. Off resets the printer to its
factory default settings.
The Energy setting minimizes the power used by the printer.
Performance may be affected, but print quality is not.
The Paper setting minimizes the amount of paper and
specialty media needed for a print job. Performance may be
affected, but print quality is not.
Energy/Paper minimizes the use of...

Menu itemDescription
Alarms
Alarm Control
Cartridge Alarm
Staple Alarm
Hole Punch AlarmSets an alarm to sound when the printer requires operator
intervention
Available selections for each alarm type are:
Off
Single
Continuous
Notes:
Single is the factory default setting for Alarm Control. Single
sounds three quick beeps.
Off is the factory default setting for Cartridge Alarm and
Staple Alarm. Off means no alarm will sound.
Continuous repeats three beeps every 10 seconds.
The Staple Alarm is available...

Menu itemDescription
Timeouts
Wait Timeout
Disabled
15–65535 secSets the amount of time in seconds the printer waits for additional
data before canceling a print job
Notes:
40 seconds is the factory default setting.
Wait Timeout is available only when the printer is using
PostScript emulation. This setting has no effect on PCL or
PPDS emulation print jobs.
Timeouts
Job Hold Timeout
5–255 secSets the amount of time the printer waits for user intervention
before it holds jobs that require unavailable...

Copy Settings menu
Menu itemDescription
Content
Text/Photo
Photograph
Printed Image
TextSpecifies the type of content contained in the copy job
Notes:
Text/Photo is the factory default setting. Text/Photo is used when the original
documents are a mixture of text and graphics or pictures.
Photograph tells the scanner to pay extra attention to graphics and pictures.
This setting increases the time it takes to scan, but emphasizes a reproduction
of the full dynamic range of tones in the original document....