Lexmark X364dw User Manual

							Menu itemDescription
Font Priority
Resident
Flash/DiskEstablishes the font search order
Notes:
Resident is the factory default setting.
A formatted flash memory option card must be installed in the printer
and operating properly for this menu item to be available.
The flash memory option cannot be Read/Write, Write, or
password‑protected.
Job Buffer Size must not be set to 100%.
PCL Emul menu
Menu itemDescription
Font Source
Resident
Download
Flash
AllSpecifies the set of fonts available
Notes:
Resident is the factory default setting. It shows the factory default set of
fonts downloaded into RAM.
Download appears only if downloaded fonts exist. It shows all the fonts
downloaded into RAM.
Flash appears only if a flash option containing fonts is installed.
A flash option must be properly formatted and cannot be Read/Write,
Write, or password protected.
All shows all fonts available to any option.
Font Name
Lets you view or change the setting from a selection list
Symbol Set
Lets you view or change the setting from a selection list
PCL Emulation Settings
Point Size
1.00–1008.00Changes the point size for scalable typographic fonts
Notes:
12 is the factory default setting.
Point Size refers to the height of the characters in the font. One point
equals approximately 1/72 of an inch.
Point sizes can be increased or decreased in 0.25‑point increments.
PCL Emulation Settings
Pitch
0.08–100Specifies the font pitch for scalable monospaced fonts
Notes:
10 is the factory default setting.
Pitch refers to the number of fixed‑space characters per inch (cpi).
Pitch can be increased or decreased in 0.01‑cpi increments.
For nonscalable monospaced fonts, the pitch appears on the display but
cannot be changed.
Understanding printer menus141
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
PCL Emulation Settings
Orientation
Portrait
LandscapeSpecifies the orientation of text and graphics on the page
Notes:
Portrait is the factory default setting.
Portrait prints text and graphics parallel to the short edge of the page.
Landscape prints text and graphics parallel to the long edge of the page.
PCL Emulation Settings
Lines per Page
1–255
60
64Specifies the number of lines that print on each page
Notes:
60 is the US factory default setting. 64 is the international default setting.
The printer sets the amount of space between each line based on the
Lines per Page, Paper Size, and Orientation settings. Select the desired
Paper Size and Orientation before setting Lines per Page.
PCL Emulation Settings
A4 Width
198 mm
203 mmSets the printer to print on A4‑size paper
Notes:
198 mm is the factory default setting.
The 203‑mm setting sets the width of the page to allow the printing of
eighty 10‑pitch characters.
PCL Emulation Settings
Auto CR after LF
On
OffSpecifies whether the printer automatically performs a carriage return (CR) after
a line feed (LF) control command
Note: Off is the factory default setting.
PCL Emulation Settings
Auto LF after CR
On
OffSpecifies whether the printer automatically performs a line feed (LF) after a
carriage return (CR) control command
Note: Off is the factory default setting.
Tray Renumber
Assign MP Feeder
Off
None
0–199
Assign Tray 
Off
None
0–199
Assign Manual Paper
Off
None
0–199
Assign Man Env
Off
None
0–199Configures the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders
Notes:
Off is the factory default setting.
None is not an available selection. It is displayed only when it is selected
by the PCL 5 interpreter.
None ignores the Select Paper Feed command.
0–199 allows a custom setting to be assigned.
Understanding printer menus142
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Tray Renumber
View Factory Def
NoneDisplays the factory default setting assigned to each tray, drawer, or feeder
Tray Renumber
Restore Defaults
Yes
NoReturns all tray, drawer, and feeder assignments to the factory default settings
Image menu
Menu itemDescription
Auto Fit
On
OffSelects the optimal paper size, scaling, and orientation
Notes:
On is the factory default setting.
The On setting overrides scaling and orientation settings for some images.
Invert
On
OffInverts bi‑tonal monochrome images
Notes:
Off is the factory default setting.
The font size can be increased in 1‑point increments.
This setting does not apply to GIF or JPEG images.
Scaling
Anchor Top Left
Best Fit
Anchor Center
Fit Height/Width
Fit Height
Fit WidthScales the image to fit the selected paper size
Note: Best Fit is the factory default setting.
Orientation
Portrait
Landscape
Rev Portrait
Rev LandscapeSets the image orientation
Note: Portrait is the factory default setting.
Set Date and Time
Menu itemDescription
View Date/TimeDisplays the time in YYYY‑MM‑DD HH:MM format
Note: This is a view only screen.
Understanding printer menus143
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Set Date/Time
Yes
NoInstructs the printer to run the setup wizard
Notes:
Yes is the factory default setting.
After completing the setup wizard by selecting Done at the Country/Region
select screen, the default becomes No.
Time Zone (North, Central, and
South America)
Hawaii *
Alaska
Tijuana (PST)
USA/Canada PST
USA/Canada MST
USA/Canada CST
USA/Canada EST
Canada AST
Caracas (VET)
Newfoundland (NST)
Brasilia (BRT)Specifies the time zone for the fax
Note: * indicates that this value does not have pre-programmed Daylight Savings
Time Start and End times.
Time Zone (Europe and Africa)
Azores (AZOT)
Praia (CVT) *
GMT (*)
Dublin, Ireland
London (BST)
Western Europe
Central Europe
Eastern Europe
Cairo (EET)
Pretoria (SAST) *
Moscow (MSK)Specifies the time zone for the fax
Note: * indicates that this value does not have pre-programmed Daylight Savings
Time Start and End times.
Time Zone (Asia)
Jerusalem (IST)
Abu Dhabi GIST)*
Kabul (AFT) *
Islamabad (PKT) *
New Delhi (IST) *
Kathmandu (NPT) *
Astana (ALMT) *
Yangon (MMT) *
Bangkok (ICT) *
Beijing (CST) *
Seoul (KST) *
Tokyo (JST) *Specifies the time zone for the fax
Note: * indicates that this value does not have pre-programmed Daylight Savings
Time Start and End times.
Understanding printer menus144
Downloaded From ManualsPrinter.com Manuals 
						

							Menu itemDescription
Time Zone (Australia and the
Pacific region)
Australia WST
Australia CST Darwin (CST) *
Australia EST
Queensland (EST) *
Tasmania (EST)
Wellington (NZST)
Not ListedSpecifies the time zone for the fax
Note: * indicates that this value does not have pre-programmed Daylight Savings
Time Start and End times.
Observe DST
On
OffAccommodates Daylight Savings Time changes
Note: On is the factory default setting.
Enable NTP
On
OffLets the printer clock synchronize with the Network Time Protocol (NTP) server
Note: On is the factory default setting.
Understanding printer menus145
Downloaded From ManualsPrinter.com Manuals 
						

							Maintaining the printer
Cleaning the exterior of the printer
1Make sure that the printer is turned off and unplugged from the wall outlet.
CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer,
unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding.
2Remove all paper from the printer.
3Dampen a clean, lint‑free cloth with water.
Warning—Potential Damage: Do not use household cleaners or detergents, as they may damage the finish of
the printer.
4Wipe only the outside of the printer.
Warning—Potential Damage: Using a damp cloth to clean the interior may cause damage to your printer.
5Make sure all areas of the printer are dry before beginning a new print job.
Cleaning the scanner glass
If you encounter print quality problems, such as streaks on copied or scanned images, clean the areas shown.
1Slightly dampen a soft, lint-free cloth or paper towel with water.
2Open the scanner cover.
12
3
4
1White underside of the ADF cover
2White underside of the scanner cover
3Scanner glass
4ADF glass
Maintaining the printer146
Downloaded From ManualsPrinter.com Manuals 
						

							3Wipe the areas shown and let them dry.
4Close the scanner cover.
Cleaning the ADF separator rollers
After you have copied over 50,000 copies using the ADF, clean the ADF separator rollers.
1Open the ADF cover.
2Unlock the separator roll.
3Remove the separator roll.
4Use a clean, lint-free cloth dampened with water to wipe the separator rollers.
Maintaining the printer147
Downloaded From ManualsPrinter.com Manuals 
						

							5Reinstall the separator roll.
6Lock the separator roll.
7Close the ADF cover.
Storing supplies
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you
are ready to use them.
Do not expose supplies to:
Direct sunlight
Temperatures above 35°C (95°F)
High humidity above 80%
Salty air
Corrosive gases
Heavy dust
Checking the status of supplies from a network computer
Note: The computer must be connected to the same network as the printer. Maintaining the printer148
Downloaded From ManualsPrinter.com Manuals 
						

							1Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, print a network setup page and locate the IP address in
the TCP/IP section.
2Click Device Status. The Device Status page appears, displaying a summary of supply levels.
Moving the printer to another location
Warning—Potential Damage: Damage to the printer caused by improper moving is not covered by the printer
warranty.
CAUTION—POTENTIAL INJURY: Follow these guidelines to avoid personal injury or printer damage:
Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
Disconnect all cords and cables from the printer before moving it.
Use the handholds located on both sides of the printer to lift it.
Make sure your fingers are not under the printer when you set it down.
Before setting up the printer, make sure there is adequate clearance around it. For more information, see “Selecting
a location for the printer” on page 9.
The printer and options can be safely moved to another location by following these precautions:
Any cart used to move the printer must be able to support its weight and have a large enough surface to support
the full footprint of the printer.
Keep the printer in an upright position.
Avoid severe jarring movements.
Shipping the printer
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit. Maintaining the printer149
Downloaded From ManualsPrinter.com Manuals 
						

							Ordering supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies
dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the
place where you purchased the printer.
Warning—Potential Damage: Damage caused by the use of a supply or replacement item not produced by the
manufacturer of this printer is not covered under warranty. Degraded print quality may result from using supplies or
replacement items not produced by the manufacturer of this printer.
Note: All life estimates for printer supplies assume printing on letter‑ or A4‑size plain paper.
Ordering toner cartridges
When 88 Cartridge Low appears or when the print becomes faded:
1Remove the toner cartridge.
2Firmly shake the cartridge side‑to‑side and front‑to‑back several times to redistribute toner.
3Reinsert the cartridge and continue printing.
Note: Repeat this procedure multiple times until the print remains faded, and then replace the cartridge.
Recommended toner cartridges and part numbers
Part NameRegular CartridgeLexmark Return Program Cartridge
Toner Cartridge X264A21G X264A11G
High Yield Toner Cartridge X264H21G X264H11G
Ordering a photoconductor kit
The printer issues a message to let you know the photoconductor kit is near its end of life. At this time, order a
photoconductor kit. You can also see the status of the photoconductor kit by printing a network setup page.
Part namePart number
Photoconductor kit E260X22G
Maintaining the printer150
Downloaded From ManualsPrinter.com Manuals