Lexmark X203n User Manual

Menu itemDescription
Auto Reduction
On
OffScales an incoming fax job so it fits the size of the paper loaded in the designated fax
source
Note: On is the factory default setting.
Fax Footer
On
OffPrints the transmission information at the bottom of each page from a received fax
Note: Off is the factory default setting.
Max Speed
2400
4800
9600
14400
33600Specifies the maximum speed in baud at which faxes are received
Note: 33600 (baud) is the factory default setting.
Block No Name Fax
On
OffEnables...

Speaker Settings
Menu itemDescription
Speaker Mode
Always Off
On until Connected
Always OnNotes:
Always Off turns the speaker off.
“On until Connected” is the factory default setting. The speaker is on and
issues a noise until the fax connection is made.
Always On turns the speaker on.
Speaker Volume
High
Medium
LowControls the volume setting
Note: High is the factory default setting.
Ringer Volume
On
OffControls the ringer volume for the fax speaker
Note: On is the factory default setting.
Distinctive...

Menu itemDescription
Print Area
Normal
Whole PageSets the logical and physical printable area
Notes:
Normal is the factory default setting. When attempting to
print data in the non‑printable area defined by the Normal
setting, the printer clips the image at the boundary.
The Whole Page setting allows the image to be moved into
the non‑printable area defined by the Normal setting, but the
printer will clip the image at the Normal setting boundary.
The Whole Page setting affects only pages printed using a...

Menu itemDescription
Orientation
Auto
Landscape
PortraitSpecifies the orientation of a multiple‑page sheet
Notes:
Auto is the factory default setting. The printer chooses between portrait and
landscape.
Long Edge uses landscape.
Short Edge uses portrait.
N‑Up Border
None
SolidPrints a border around each page image
Note: None is the factory default setting.
Quality menu
Menu itemDescription
Print Resolution
600 dpi
1200 dpi
1200 Image Q
2400 Image QSpecifies the printed output resolution
Note: 600 dpi is...

PostScript menu
Menu itemDescription
Print PS Error
On
OffPrints a page containing the PostScript error
Note: Off is the factory default setting.
PCL Emul menu
Menu itemDescription
Font Source
Resident
Download
AllSpecifies the set of fonts available
Notes:
Resident is the factory default setting. It shows the factory default set of
fonts downloaded into RAM.
Download appears only if downloaded fonts exist. It shows all the fonts
downloaded into RAM.
All shows all fonts available to any option.
Font...

Menu itemDescription
PCL Emulation Settings
A4 Width
198 mm
203 mmSets the printer to print on A4‑size paper
Notes:
198 mm is the factory default setting.
The 203 mm setting sets the width of the page to allow the printing of
eighty 10‑pitch characters.
PCL Emulation Settings
Auto CR after LF
On
OffSpecifies whether the printer automatically performs a carriage return (CR) after
a line feed (LF) control command
Note: Off is the factory default setting.
PCL Emulation Settings
Auto LF after CR
On...

Menu itemDescription
NPA Mode
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
Network Buffer
Auto
3K to Sets the size of the network input buffer
Notes:
Auto is the factory default setting.
The value can be changed in...

Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > Reports or Network
Reports
Menu itemDescription
Print Setup PagePrints a report containing information about the current network setup
Note: The Print Setup Page contains information about the network printer settings, such as the
TCP/IP address.
Network Card menu
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network  > Std Network Setup or Net  Setup > Network Card
Menu...

Menu itemDescription
View HostnameLets you view the current TCP/IP hostname
Note: This can be changed only from the Embedded Web Server.
IP AddressLets you view or change the current TCP/IP Address
Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP
settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that
support BOOTP and RARP.
NetmaskLets you view or change the current TCP/IP Netmask
GatewayLets you view or change the current TCP/IP Gateway
Enable...

Menu itemDescription
View Hostname
View Address
View Router AddressLets you view the current setting
Note: These settings can be changed only from the Embedded Web
Server.
Enable DHCPv6
On
OffEnables DHCPv6 in the printer
Note: On is the factory default setting.
USB menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default...