Lexmark E360d User Manual

Settings menu
General Settings menu
Menu itemDescription
Display Language
English
Francais
Deutsch
Italiano
Espanol
Dansk
Norsk
Nederlands
Svenska
Portuguese
Suomi
Russian
Polski
Magyar
Turkce
Cesky
Simplified Chinese
Traditional Chinese
Korean
JapaneseSets the language of the text appearing on the display
Note: All languages may not be available for all printers.
Eco‑Mode
Off
Energy
Energy/Paper
PaperMinimizes the use of energy, paper, or specialty media
Notes:
Off is the factory default setting. Off...

Menu itemDescription
Run Initial Setup
Yes
NoInstructs the printer to run the setup wizard
Notes:
Yes is the factory default setting.
After completing the setup wizard by selecting Done at the
Country select screen, the default setting becomes No.
Alarms
Cartridge Alarm
Off
SingleThe display shows a message when the toner is low
Notes:
Off is the factory default setting. The Toner is low
message will appear as a warning.
Single means the Toner is low message will appear and
the indicator light will blink...

Menu itemDescription
Print Recovery
Jam Recovery
Auto
On
OffSpecifies whether the printer reprints jammed pages
Notes:
Auto is the factory default setting. The printer reprints
jammed pages unless the memory required to hold the
pages is needed for other printer tasks.
On sets the printer to always reprint jammed pages.
Off sets the printer to never reprint jammed pages.
Print Recovery
Page Protect
Off
OnLets the printer successfully print a page that may not have printed
otherwise
Notes:
Off is the...

Menu itemDescription
Print Area
Normal
Whole PageSets the logical and physical printable area
Notes:
Normal is the factory default setting. When attempting to
print data in the non‑printable area defined by the Normal
setting, the printer clips the image at the boundary.
The Whole Page setting allows the image to be moved into
the non‑printable area defined by the Normal setting, but the
printer clips the image at the Normal setting boundary.
The Whole Page setting affects only pages printed using a
PCL...

Menu itemDescription
Duplex Binding
Long Edge
Short EdgeDefines the way duplexed pages are bound and how the printing on the back of the
page is oriented in relation to the printing on the front of the page
Notes:
Long Edge is the factory default setting.
Long Edge specifies that binding be placed on the left edge of portrait pages
and the top edge of landscape pages.
Short Edge specifies that binding be placed on the top edge of portrait pages
and the left edge of landscape pages.
Copies
1–999Specifies...

Menu itemDescription
N‑up (pages‑side)
Off
2‑Up
3‑Up
4‑Up
6‑Up
9‑Up
12‑Up
16‑UpSpecifies that multiple‑page images be printed on one side of a sheet of paper
Notes:
Off is the factory default setting.
The number selected is the number of page images that will print per side.
N‑up Ordering
Horizontal
Reverse Horizontal
Reverse Vertical
VerticalSpecifies the positioning of multiple‑page images when using N‑up (pages‑sides)
Notes:
Horizontal is the factory default setting.
Positioning depends on the number...

Menu itemDescription
Toner Darkness
1–10Lightens or darkens the printed output
Notes:
8 is the factory default setting.
Selecting a smaller number can help conserve toner.
Enhance Fine Lines
Off
OnEnables a print mode preferable for files such as architectural drawings, maps, electrical
circuit diagrams, and flow charts
Notes:
Off is the factory default setting.
To set Enhance Fine Lines using the Embedded Web Server, type the network
printer IP address in a browser window.
Gray Correction
Auto...

Menu itemDescription
Defragment Flash
No
YesPrepares the flash memory to receive new data by retrieving lost storage space
Warning—Potential Damage: Do not turn off the printer while the flash memory is
defragmenting.
Notes:
An optional flash memory card must be installed in the printer and operating
properly for this menu item to be available. The flash memory card must not
be Read/Write or Write protected.
No cancels the defragment request.
Selecting Yes reformats the flash memory after transferring...

PCL Emul menu
Menu itemDescription
Font Source
Resident
Download
Flash
AllSpecifies the set of fonts available
Notes:
Resident is the factory default setting. It shows the factory default set of
fonts downloaded into RAM.
Download appears only if downloaded fonts exist. It shows all the fonts
downloaded into RAM.
Flash appears only if a flash option containing fonts is installed.
A flash option must be properly formatted and cannot be Read/Write,
Write, or password protected.
All shows all fonts...

Menu itemDescription
PCL Emulation Settings
Lines per Page
1–255
60
64Specifies the number of lines that print on each page
Notes:
60 is the US factory default setting. 64 is the international factory default
setting.
The printer sets the amount of space between each line based on the
Lines per Page, Paper Size, and Orientation settings. Select the desired
Paper Size and Orientation before setting Lines per Page.
PCL Emulation Settings
A4 Width
198 mm
203 mmSets the printer to print on A4‑size paper...