Lexmark E232 User Manual

 
Using the operator panel
61
Close door
Load media
Light sequence:
Error—On
What this light sequence means:
The printer door is open.
What you can do:
Close the door.
Light sequence:
Continue—On
Load Paper—On
What this light sequence means:
The printer is out of media, or the media did not feed properly.
What you can do:
Load media into tray 1 or the optional 550-sheet tray and 
press Continue to resume printing.
Check that the media is loaded correctly in tray 1 or the 
optional 550-sheet tray....

 
Using the operator panel
62
Load manual feeder
Print side two of a duplex job
Light sequence:
Continue—On
Load Paper—Blink
What this light sequence means:
The printer prompts you to load a single sheet of media in the manual 
feed.
What you can do:
Load media, with the side to be printed facing the front of the 
printer, into the manual feed.
Press Continue  to resume printing.
Press and hold Cancel  to reset the printer.
Light sequence:
Continue—Blink
Load Paper—On
What this light sequence...

 
Using the operator panel
63
Invalid engine code / Invalid network code
To n e r  l o w
Light sequence:
Ready—On
Error—On
What this light sequence means:
The code in an internal print server has not been programmed, or the 
programmed code is not valid.
What you can do:
Download valid network code to the internal print server. Press 
Continue twice quickly to see the secondary error code. See 
“Secondary error codes” on page 69 for more information.
Light sequence:
Toner Low/Replace PC Kit—On
What...

 
Using the operator panel
64
Photoconductor kit near full
Replace photoconductor kit
Light sequence:
Continue—On
Toner Low/Replace PC Kit—Blink
What this light sequence means:
The photoconductor kit’s drum is almost full and will need replacing 
soon.
Note:The Toner Alarm (see page 103) must be turned on 
for this message to appear.
What you can do:
Press Continue  to resume printing.
Replace the photoconductor kit. See “How to change a 
photoconductor kit” on page 112 for more information.
Light...

 
Using the operator panel
65
Replace photoconductor kit (printer hard stop)
Unsupported toner cartridge / Toner cartridge is not installed
Light sequence:
Continue—On
Toner Low/Replace PC Kit—Blink
Error—Blink
What this light sequence means:
The photoconductor kit’s drum is full and needs replacing. The printer 
will not print any more pages until the photoconductor kit is replaced.
What you can do:
Replace the photoconductor kit. (See “How to change a 
photoconductor kit” on page 112 for help.)...

 
Using the operator panel
66
Change invalid toner cartridge
Programming engine code / Programming system code
Light sequence:
Toner Low/Replace PC Kit—On
Error—Blink
What this light sequence means:
The toner cartridge you are using was not designed for your printer.
What you can do:
Install a toner cartridge made for your printer (see “What supplies 
do I need and how do I order them?” on page 105).
Light sequence:
Ready—On
Toner Low/Replace PC Kit—On
Load Paper—On
What this light sequence means:...

 
Using the operator panel
67
Cancel job / Reset printer
Service error
Light sequence:
Continue—On
Ready—On
Toner Low/Replace PC Kit—On
Load Paper—On
Paper Jam—On
Error—On
What this light sequence means:
The current print job is canceled.
The printer is resetting to the user default settings. Any active 
print jobs are canceled. A user default setting remains in 
effect until you change it or until you restore the factory 
default settings.
What you can do:
Wait for the message to clear.
Light...

 
Using the operator panel
68
Printer error
Paper jam printer error
Light sequence:
Continue—On
Error—On
What this light sequence means:
The printer has one of the following errors:
Memory is full, insufficient to save what is in the buffer, or 
insufficient to defragment flash memory.
A page is too complex to print or is shorter than the set page 
margins.
Resolution of a formatted page is reduced to 300 dpi.
A font error occurred.
Communication with the host computer is lost.
What you can do:...

 
Using the operator panel
69
Secondary error codes
When the Error  and Continue  lights are both on, a secondary error has occurred. 
When the Paper Jam  and Continue  lights are both on, a paper jam secondary error 
has occurred. 
Press and release Continue twice quickly to display the secondary error code light sequence.
Downloaded From ManualsPrinter.com Manuals 

 
Using the operator panel
70
Paper jam at the input sensor
Paper jam in the manual feeder
Light sequence:
Continue—On
Ready—On
Paper Jam—On
What this light sequence means:
A paper jam has occurred at the input sensor, which can be either 
after the paper leaves the tray and enters the printer or in the manual 
feeder.
What you can do:
Clear the paper jam. See “How to clear paper jams” on page 26 
for more information.
Light sequence:
Continue—On
Ready—Blink
Paper Jam—On
What this light sequence...