Lexmark E120n User Manual

Overview of the Lexmark E120 operator panel
11
Using the operator panels
Load media (Ready / Data light blinks once)
Print side two of a duplex job (Ready / Data light blinks once)
Memory full (Ready / Data light blinks three times)
Host interface disabled (Ready / Data light blinks five times)
Jam in the printer paper path (Ready / Data light blinks ten times)
Jam in Tray 1 / priority feeder (Ready / Data light blinks four times)
Short paper (Ready / Data light blinks three times)
Toner low (Ready /...

Overview of the Lexmark E120 operator panel
12
Using the operator panels
Operator panel codes for the Lexmark E120
Following are explanations of the primary and secondary light sequences, and what can be done to clear them.
Primary Codes
Ready / Power Saver 
Light sequence:
Ready / Data—On
Message:
Printer is ready to receive and process data.
Printer is in Power Saver mode.
Printer is functioning properly.
Note:To change the Power Saver setting, use the Local Printer Setup Utility (see Software and...

Overview of the Lexmark E120 operator panel
13
Using the operator panels
Busy 
Waiting 
Light sequence:
Ready / Data—Blinking
Message:
Printer is busy receiving and processing data or printing.
Solution:
Busy:
–Wait for message to clear.
–Press and release to cancel job.
–Press and hold to reset printer.
Printing:
–Wait for pages to print. The ready light blinks as pages print. The Ready light is on when printing 
stops.
–Press and release  to cancel job.
–Press and hold  to reset printer....

Overview of the Lexmark E120 operator panel
14
Using the operator panels
Cancel job / Reset printer
 
Flushing buffer 
Invalid engine code 
Light sequence:
Ready / Data—On
Error—On
Message:
Current job is canceled.
Printer is resetting to the user default settings. All active print jobs are canceled. 
A user default setting remains in effect until the user changes it or until the user 
restores the factory default settings.
Solution:
Press and hold to reset printer.
Light sequence:
Ready / Data—On...

Overview of the Lexmark E120 operator panel
15
Using the operator panels
Not ready 
Printing font list or menu settings page 
Programming engine code or system code 
Light sequence:
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—Blinks once
Message:
Printer is not ready to receive or process data, or printer port is offline.
Solution:
Press to return to Ready or Busy state.
Press and release to cancel job.
Press and hold to reset printer....

Overview of the Lexmark E120 operator panel
16
Using the operator panels
Restoring factory defaults
 
Cartridge region mismatch 
Light sequence:
Ready / Data—On
Error—On
Message:
Printer is resetting to the original factory default settings.
Solution:
Press and hold to reset printer.
Light sequence:
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—Blinks four times
Message:
The toner cartridge being used is not programmed for the specific...

Overview of the Lexmark E120 operator panel
17
Using the operator panels
Missing cartridge / Defective cartridge detected 
Open door
Light sequence:
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light
sequence.
Ready / Data—Blinks three times
Message:
Either the toner cartridge is missing, the long-life photoconductor 
kit is missing, or a defective toner cargridge is detected.
Solution:
First, check to see if a toner cartridge is installed. If the toner cartridge is...

Overview of the Lexmark E120 operator panel
18
Using the operator panels
Complex page 
ENA connection lost 
Light sequence:
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—Blinks three times
Message:
The page may not print correctly because the print information 
on the page is too complex (that is, too large for printer memory).
Solution:
Turn printer off and back on to try printing the page again. If not successful:
Press to clear message and...

Overview of the Lexmark E120 operator panel
19
Using the operator panels
Insufficient collation area 
Load media 
Light sequence:
Error—On
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—Blinks three times
Message:
Printer memory does not have the free space necessary to 
collate print job. May occur due to one of the errors listed below:
Printer memory is full.
A page is too complex to print.
Memory is insufficient to save what is in the print buffer....

Overview of the Lexmark E120 operator panel
20
Using the operator panels
Print side two of a duplex job 
Memory full 
Light sequence:
Error—Blinking
Secondary light sequence:
Press twice quickly to see the secondary light 
sequence.
Ready / Data—Blinks once
Message:
Print the other side of current duplex print job.
Solution:
Insert print job into priority feeder using instructions in the driver pop-up menu to orient pages correctly, 
then press to resume printing.
Press to cancel print job.
Press and...