Lexmark C 950 Service Manual

Repair information 4-117
  5058-030
Go Back Previous
Next
4.Release the two clamps (C) to release the harness.
5.Swing the PCBA door open.
6.Remove the four screws (D) securing the main power GFI interface to the machine.
7.Pull the main power GFI interface out of the machine. 
8.Disconnect all the cables and remove the main power GFI interface. 
Warning:  Damage may occur if the main power GFI interface is not re-installed correctly. Make sure that 
all cables are properly reconnected. Use the following...

4-118  Service Manual 5058-030  
Go Back Previous
Next
Main power switch removal
1.Remove the rear upper cover. See “Rear upper cover removal” on page 4-16.
2.Remove the rear lower cover. See “Rear lower cover removal” on page 4-14.
3.Remove the printer right cover. See “Printer right cover removal” on page 4-11.
4.Remove the LVPS front fan guide. See “LVPS front fan guide removal” on page 4-108.
5.Remove the waste toner sensor guide. See “Waste toner sensor guide removal” on page 4-193.
6.Remove the...

Repair information 4-119
  5058-030
Go Back Previous
Next
4.Detach the media feed lift motor. 

4-120  Service Manual 5058-030  
Go Back Previous
Next
Media out actuator removal
1.Remove the appropriate feeder unit. See “Printer tray 1 feeder removal” on page 4-141, “Tray module 
media feeder removal” on page 4-212, “TTM tray 4 media feeder removal” on page 4-225, or “TTM 
tray 3 feeder removal” on page 4-221.
2.Release the tab (A) securing the media out actuator to the assembly.
3.Remove the media out actuator.
Media size switch PCB removal
1.Remove the Media tray 1 from the machine. 
2.Remove the...

Repair information 4-121
  5058-030
Go Back Previous
Next
3.Disconnect the cable (B).
4.Remove the media size switch PCB.
Media transport/MPF drive motor removal
1.Remove the rear upper cover. See “Rear upper cover removal” on page 4-16.
2.Disconnect the input option cable (A). 

4-122  Service Manual 5058-030  
Go Back Previous
Next
3.Remove the eight screws (B) securing the PCBA door to the machine.
4.Release the two clamps (C) to release the harness.
5.Swing the PCBA door open. 

Repair information 4-123
  5058-030
Go Back Previous
Next
6.Disconnect the cable from the media transport/MPF drive motor.
7.Release the clamp securing the harness to the machine.
Note:  The lower right screw is obscured by the large harness. 

4-124  Service Manual 5058-030  
Go Back Previous
Next
8.Remove the four screws (D) securing the media transport/MPF drive motor to the machine.
Warning:  When removing the media transport/MPF drive motor, ensure that the plastic bushing does not 
become damaged.
9.Remove the media transport/MPF drive motor from the machine.
Replacement warning: When replacing the media transport/MPF drive motor, ensure that the shaft, gears, and 
bushing are properly aligned or damage may occur.
MPF roller removal...

Repair information 4-125
  5058-030
Go Back Previous
Next
5.Press the three latches on each MPF feed roller.
6.Remove the MPF feed rollers.
MPF tray feeder removal
1.Remove the left rear lower cover. See “Left rear lower cover removal” on page 4-6.
2.Open the printer left duplex door.
3.Release the harness (A) from the clamps.
4.Close the printer left duplex door.
5.Disconnect the cable (B). 

4-126  Service Manual 5058-030  
Go Back Previous
Next
6.Remove the two screws (C).
7.Remove the MPF tray feeder.
Operator panel assembly (SFP) removal
1.Remove the operator panel front cover. See “Operator panel front cover (SFP)” on page 4-8. 
2.Remove the screw (A) securing the ground wire to the machine.
3.Remove the two screws (B) securing the operator panel to the machine.