Lexmark C 746 Service Manual

Repair information4-25
 5026
Go Back Previous
Next
7.Touch Quick Test in the Cyan menu.
Two pages print. You may have to print these pages several times until you get T (Top Margin) and 
Z (Skew) aligned. Do not go to step 2 until T and Z are aligned. The first page is similar to the following: 

4-26Service Manual 5026 
Go Back Previous
Next
8.Determine the line under Fine Adjustment that is closest. If the value is beyond the Fine Adjustment scale, 
use either of the Coarse Adjustment scales.
9.Enter the number determined from the Fine Adjustment scale or the Coarse Adjustment scales on the part 
of the page for the “T” value. The current value is automatically entered on the sheet. At this point, it should 
be zero.
10.Enter the “New Cyan T value” on the operator panel and touch   to save the...

Repair information4-27
 5026
Go Back Previous
Next
12.Repeat this process for skew (Z). Dont forget to subtract the T value and add the current cyan Z value to 
obtain the new skew (Z) value.
An example is shown below:
13.Continue to follow the directions on the bottom of the first page to find the Cyan Top Margin (T), the 
Skew (Z), and on the second page of the Quick Test page, the Left Margin (L), Right Margin (R), and 
Bow (P).
14.Repeat steps 1 through 13 for yellow and magenta.
Note:  Start each...

4-28Service Manual 5026 
Go Back Previous
Next
Printer removal procedures
Precautions to take before maintenance work
Do not implement any operation, removal, or modification and so on, which is not presented in this manual. 
1.Turn the printer power off and unplug the power cable from the outlet prior to starting 
removals or checks.
2.Prior to starting any repairs, read and understand the warnings in this manual. 
•High temperature
•High voltage 
•Laser radiation
3.Confirm the direction of all parts...

Repair information4-29
 5026
Go Back Previous
Next
Cover removals
Front access cover assembly removal
See Front access door cover assembly for the part number for the models you need on page 7-3.
1.Remove the paper tray.
2.Disconnect the transfer module cable (A). 
3.Press the two tabs (B) to release the front access door cover assembly.
4.Press the two tabs (C) on either side of the transfer module, and lift out the transfer module.
Note:  Leave the photoconductor units on the transport belt when...

4-30Service Manual 5026 
Go Back Previous
Next
5.Looking down at the keyed end of the restraint (D), twist the end clockwise, slide the restraint upward 
through the slit (E), and slip the end of the restraint through the keyed hole (F). Repeat for the other side.
DF E 

Repair information4-31
 5026
Go Back Previous
Next
6.Close the front access door assembly.
7.Remove the two screws (G) that attach the pivot pin to the front access door cover assembly.
8.Remove the bracket (H).
9.Remove the front access cover assembly.
Left cover removal
See “Left cover” on page 7-3 for the part number.
1.Remove the paper tray.
2.Remove the waste toner assembly. See “Waste toner assembly removal” on page 4-176. 
3.Open the front access door.
4.Open the top access door.
5.Remove the two...

4-32Service Manual 5026 
Go Back Previous
Next
7.Remove the screws (D) from the rear left cover.
8.Unsnap the right cover from the top cover, then lift and remove the left cover and rear left cover together.
Note:  Because the paper tray dust cover is loose at this point, set it aside.
Note:  If you are removing the left cover to access another part, leave the left cover and the rear left cover 
attached, and you are done. If you need to replace the left cover FRU, continue with the next step to remove...

Repair information4-33
 5026
Go Back Previous
Next
9.Separate the left cover and rear left cover by sliding the left rear cover as shown to disengage the latch (E). 

4-34Service Manual 5026 
Go Back Previous
Next
Operator panel assembly removal (C746)
See operator panel assembly with card on page 7-3 for the part number. 
Warning:  This part might contain customer confidential information. See “Data Security Notice” on page 4-1 
for more details. After removing this part, return it to your next level of support so any data can be 
removed. If the customer requests to keep the part, they must sign a confirmation of memory device 
retention form.
Warning:  When...