Lawn Mower EMAK El 63 Instructions Manual

EN 31 MAINTENANCE
set to 60-65 Nm. If necessary, replace nuts and bolts only with GENUINE
SPARE PARTS.
6.3.2 C
UTTING DECK ALIGNMENT
The cutting deck should be properly set to obtain a good cut. 
To achieve good results from cutting, the front part should
always be 5 - 6 mm lower than the rear.
1. Put the machine onto a flat surface and
check the tyre pressure;
2. put 26 mm blocks (1) under the front edge
of the deck and 32 mm blocks (2) under
the rear edge, then put the lifting lever into
position «1»;...

6.3.4 BRAKE ADJUSTMENT
If the braking distance lengthens, the
brake will need adjusting. 
The adjustment will need to be made with
the parking brake ENGAGED. 
1. Remove the collector channel (1),
which is fixed by a pin (2) and split pin
(3);
2. turn the adjusting nut (4) (which is
reached by taking off the engine cover)
until there is a distance of 86-88 mm
between the bracket (5) and the upper
part of the lever (6).
3. refit the collector channel (1) and put
the pin (2) and split pin (3) back in...

EN 33 MAINTENANCE
4. check that the spring (7) of the engage-
ment cable is not too taut or too loose.
Otherwise, turn the adjusting nut (8) until
the spring reaches the right condition.
5. check the measurement of the spring (6)
again;
6. refit the collector channel (1), and always
put back the pin (2) and the split pin (3).
6.4 DISMANTLING AND REPLACEMENT
6.4.1 R
EPLACING WHEELS
1. Place the machine on a flat surface and
put blocks under a load-bearing part of
the frame on the side of the wheel to be...

6.4.3 ELECTRIC AND PROTECTION SYSTEM
In the electric start models:
The electric system and the electronic card
are protected by a fuse. When it blows the
machine stops, so in this case:
1. remove the engine housing (1) using a
screwdriver;
2. replace the fuse (2) with another one
with the same capacity; 
3. remount the engine housing (1).
The fuse capacity is indicated on the fuse.
A blown fuse must
always be replaced by one of the same
type and ampere rating, and never with
one of another rating.
If you...

EN 35 TROUBLESHOOTING
7. TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
1.With the key
on «START» the
starter motor
does not run
2.With the key on
«START» the
starter motor runs
but the engine
does not start
3. The engine
stopsElectronic card blocked due to:
– flat battery or sulphated battery plates
– fuse blown
– bad earthing to the engine or the frame
– earth connections of the microswitches
disconnected
– badly earthed starter motor
– you are not ready for starting
– faulty fuel supply
– faulty...

PROBLEM LIKELY CAUSE SOLUTION
EN 36TROUBLESHOOTING
4. The engine
does not start
5. The engine
stops
6.Starting is difficult
or the engine runs
erratically
7.Weak engine per-
formance during cut-
ting
8.Engine stops when
blade is engaged– earth connections of the microswitches
disconnected
– you are not ready for starting      
– faulty fuel supply
– faulty ignition
– earth connections of the microswitches
disconnected
– fault in carburation
– forward speed too high in relation to
cutting height
– you are...

EN 37 TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
– check the tyre pressure (☛5.3.2)
– realign the cutting deck to the ground
(☛6.3.2)
– check that the blade is fitted properly
(☛6.3.1)
– sharpen or fit new blade (☛6.3.1)
– reduce forward speed and/or raise the
cutting deck (☛5.4.5)
– wait for the grass to dry
– remove the grass-catcher and empty
the collector channel (☛5.4.7)
– clean the cutting deck (☛5.4.10)
– balance or replace the blade if dam-
aged (☛6.3.1)
– check that the blade is fastened...

EN 38ACCESSORIES ON REQUEST
8. ACCESSORIES ON REQUEST
1. KIT FOR “MULCHING”
It finely chops the grass cuttings and leaves them
on the lawn, instead of collecting them in the
grass-catcher.
1 

EN 39 SPECIFICATIONS
9. SPECIFICATIONS
Electrical system (  Only in the electric start models).................................. 12 V
Battery (  Only in the electric start models).............................................. 7,2 Ah
Front tyres  .............................................................................................11 x 4.00-4
Rear tyres  ............................................................................................. 13 x 5.00-6
Front tyre pressure...

EINFÜHRUNG
Sehr geehrte Kundin, sehr geehrter Kunde,
Wir danken Ihnen, dass Sie unseren Produkten den Vorzug gegeben haben und wün-
schen Ihnen, dass Ihnen der Gebrauch Ihrer neuen Rasenmähmaschine Freude macht
und Ihren Erwartungen vollkommen entspricht.
Dieses Handbuch wurde herausgegeben, um Sie mit Ihrer Maschine vertraut zu machen
und diese sicher und wirksam einsetzen zu können. Beachten Sie, dass das Handbuch
ein wesentlicher Bestandteil der Maschine ist. Halten Sie es stets griffbereit, um es...