Land Rover Rover 214 Repair 1689 11 Rover Manual

15Undo the window outer rear trim panel
retaining screw and remove the panel from
the door.
16Remove the screw securing the outer
window sealing strip to the rear of the door
then carefully prise the strip out of the door
panel and remove it from the vehicle.
17Slacken and remove the bolt securing the
lower end of the rear window glass channel to
the door panel and recover the spacer,
through which the bolt passes, from inside the
door panel. Undo the nut securing the channel
to the door then release the...

retained by the spring clip, then adjust the
mirror to the required position.
Mirror assembly
7Refitting is a reverse of the removal
procedure.
17 Boot lid- removal, refitting
and adjustment
2
Removal
1Open the boot lid then disconnect the
release cable outer from the lock bracket and
release the cable inner from the lock operating
mechanism.
2Disconnect the wiring connectors from the
boot lid lock warning lamp switch.
3Remove the access cover from the left-
hand side of the boot lid and free the...

on the top of the release lever cover to gain
access to the retaining screw. Undo the screw
and lift off the release lever cover (see
illustrations).
4On four and five-door models, open the
right-hand rear door and undo the two screws
securing the sill finisher to the floor, then
remove the sill finisher and carpet retainer.
Carefully prise out the lower trim panels from
the centre and rear door pillars.
5On three-door models, remove the four
screws securing the right-hand lower rear
seat side trim panel...

6Have an assistant support the tailgate then
raise the spring clips and pull the support
struts off their balljoint mountings on the
tailgate. Undo the four hinge retaining bolts
and remove the tailgate from the vehicle,
noting any shims which may be fitted between
the hinge and tailgate.
Refitting and adjustment
7Offer up the tailgate, positioning any shims
necessary between the hinge and tailgate.
Refit the hinge bolts. Press the support struts
firmly onto the balljoint mountings and clip the
spring...

23 Quarterlight glass 
(3-door Hatchback)- 
removal and refitting
3
Removal
1Remove the rear window parcel shelf, then
fold the rear seat cushion fully forwards and
remove the rear seat back. Remove the
rubber seal from the rear seat back retaining
catch.
2Remove the four screws securing the rear
seat side trim panel to the luggage
compartment carpet and carefully peel the
front door sealing strip away from the door
pillar, so that the front edge of the trim panel
is freed. The panel can then be released...

service key mustbe fitted to prevent
accidental firing of the pretensioner.
6Remove the two Torx bolts securing the
rear of the seat slides to the floor and remove
the seat from the vehicle. Handle the seat
gently once removed, to avoid any chance of
the service key becoming dislodged.
Rear seat cushion - 214 models
7Carefully prise off the hinge covers from the
front of the seat cushion, then undo the two
Torx bolts securing the hinges to the floor.
The cushion can then be lifted out of position
and...

2Remove the cover from the belt upper
mounting, undo the seat belt retaining nut and
detach the belt (see illustration).
3Remove the cap from the seat belt lower
mounting bolt then undo the bolt and detach
the belt from the floor (see illustration).
4Undo the two bolts securing the inertia reel
to the door pillar and remove the reel and belt
assembly from the vehicle (see illustration).
Front seat belt - 3-door models
5Remove the rear window parcel shelf then
fold the rear seat cushion fully forwards...

17Undo the two bolts securing the inertia
reel to the body and remove the belt and reel
assembly from the vehicle.
Rear seat side belt - 4-door models
18Remove the rear seat cushion and back.
19Carefully examine the luggage
compartment side trim panel and remove all
its retaining screws. Release the trim panel
and remove it from the luggage compartment.
20Remove the seat belt lower mounting bolt
and detach the belt from the body (see
illustration).
21Prise off the cover from the seat belt
upper guide...

retaining clip and disengage the slide from the
gearchange lever (see illustration).
4Remove the four front console section
retaining screws and remove it from the
vehicle (see illustrations).
Refitting
5Refitting is a reversal of the removal
procedure.
31 Facia- 
removal and refitting
3
Warning: Read carefully the
precautions listed in Chapter 12,
appertaining to vehiclesequipped with airbags (SRS) before
disturbing the steering column.
Removal
1Disconnect the battery negative terminal.
From within the...

8With the panel removed, disconnect the
two block connectors from the relay module
and release the wiring retaining clip from the
facia mounting bracket. Use a screwdriver to
release the retaining clip and remove the relay
module.
9Slacken the two bolts securing the facia to
the mounting bracket on the transmission
tunnel, then remove the bolts along with the
relay module mounting bracket (see
illustration).
10Open the glovebox and remove the door
demister duct from the left-hand end of the
facia....