Land Rover Range Rover Workshop Pre Delivery Inspection Pdi Lm 3rd Edition Rover Manual

							PRE-DELIVERY INSPECTION
01-6 PROCEDURES
13.Press FM button on the MFD, hold down until 
the display changes to  AUTOSTORE. Using 
preset buttons A1 to A6, assign preferred 
station to preset button. Depress and hold 
preset button, the station signal will 
momentarily mute and will return in 
approximately 8 seconds. At this point an 
asterisk (*) will appear adjacent to the selected 
preset, denoting the successful setting.
14.Repeat the process for the 5 remaining FM 
presets.
15.Press the AM select button, preset 6 AM 
stations by repeating the FM preset procedure.
16.Press the Clock setting button on the MFD, wait 
for mode to change. Using the upper right hand 
pair of preset buttons, toggle and select either 
the 12 or 24 hour time setting. Then set hours 
and minutes.  
						

							PRE-DELIVERY INSPECTION
PROCEDURES 01-7
17.Following the screen icons and using the 4 
indicated buttons, set the Day, Month and Year.
18.Turn ignition to the off position and remove key 
from switch.
19.Open upper and lower tailgates.20.Remove LH loadspace access panel.
21.Remove satellite navigation CD from 
packaging and place in drive.
22.Fit access panel to rear quarter panel. 
						

							PRE-DELIVERY INSPECTION
01-8 PROCEDURES
Vehicle exterior
1.Inspect road wheels and tyres for damage, 
check wheel retaining nuts for torque, 140 Nm 
(103 lbf.ft).
2.Lift spare wheel cover and support with prop.
3.Set tyre pressures: 
lFront 2.3 bar (33 psi).
lRear 2.5 bar (36 psi).
lFull size Spare 2.5 bar (36 psi).
lSpace Saver Spare 4.1 bar (60 psi).
4.Fit spare wheel cover and secure in clips.
5.Close upper and lower tailgates.
6.Check the exterior of the vehicle is clean and 
free from damage.
Road test 
1.Whilst vehicle is on test, press the fascia 
mounted Tyre Pressure Monitor button to 
calibrate the tyre pressure ECU, if fitted.
2.Before driving vehicle, check the operation of: 
lLights, indicators, wipers, wash/wipe and 
hazard warning.
lSeats and seat belts
lFascia switches
lHandbrake
3.Start vehicle and check operation of:
lStarter/Inhibitor switch
lElectric mirrors, including power fold
lSunshine roof, if fitted
4.During the road test, ensure the transfer box 
range change functionality is tested by using 
the following method.
lWith engine running and handbrake 
applied, select neutral on automatic gearbox
lRequest range change for low gear with 
switch - wait until change is complete
lRequest range change into high gear with 
switch - wait until change is complete
lRepeat 5 times
lEnsure high range is left selected5.Whilst driving the vehicle check the operation of 
cruise control and gearchange including 
sequential operation.
6.Check for any unusual noises from power train, 
suspension or braking system. Investigate any 
findings.
7.Check for squeaks and rattles from vehicle 
interior. Investigate any findings.
8. Satellite Navigation, if fitted: Check after test 
drive that the satellite navigation has 
established global position.
9.Press the menu button on the MFD, using the 
right hand rotary control follow the screen 
icons. Navigate until the global position can be 
read.
10.Position vehicle on lift.
11.Fit front bumper towing eye cover.
12.Raise vehicle on lift.
13.Visually check beneath vehicle for leaks from 
power train components.
14.Lower vehicle. 
						

							PRE-DELIVERY INSPECTION
PROCEDURES 01-9
Quality assurance checks
1.Update the vehicle service record.
2.Check the Service Action Bulletin register, 
ensure all current outstanding bulletins are 
completed prior to customer handover.
3.Ensure a copy of the PDI sheet is added to the 
Customer/Vehicle history file.
4.Ensure all relevant vehicle details are included 
in the Service Portfolio and are endorsed with 
the dealers stamp.
5.Record locking wheel nut code and place in 
Customer/Service history file, if applicable.
6.Ensure vehicle literature pack and security item 
contents are correct.
7.Place literature pack, mats and security items 
in the vehicle, if applicable.
8.Valet vehicle prior to release to customer.