Land Rover Range Rover Workshop Pre Delivery Inspection Pdi Lm 3rd Edition Rover Manual

							Workshop Manual
Pre Delivery Inspection
NRRWM  21/11/01  11:23 am  Page 29 
						

							WORKSHOP MANUAL - PRE-DELIVERY 
INSPECTION (PDI)
LRL0516ENG 3rd Edition
© 2002 Land Rover
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, 
electronic, mechanical, recording or other means without written prior permission from Land Rover. 
						

							CONTENTS
CONTENTS 1
PRE-DELIVERY INSPECTION .................................................................  01-1
PROCEDURES
Pre-delivery inspection (PDI) ..........................................................................................................  01-1 
						

							CONTENTS
2CONTENTS 
						

							PRE-DELIVERY INSPECTION
PROCEDURES 01-1
PRE-DELIVERY INSPE CTION PROCEDURES
Pre-delivery inspection (PDI)
$% 10.10.01
Preliminary 
1.After parking vehicle in work bay, remove keys 
from ignition switch.
2.Check the integrity of factory fitted door and 
tailgate closure seals. Should a seal be broken 
or missing,  ensure the tool kit and spare wheel 
are present. Also check that no internal 
damage to trim has occurred.
3.Remove door and tailgate closure seals.
4.Open bonnet for access.5.Loosen nut and disconnect the transportation 
cut off switch cable from the battery negative 
terminal.
CAUTION: After switching off the ignition, 
wait 2 minutes before disconnecting the 
battery. Failure to wait two minutes will 
damage the navigation computer.
6.Loosen nut and disconnect the transportation 
cut off switch extension lead from the battery 
negative earth lead.
7.Remove and dispose of harness and switch. 
						

							PRE-DELIVERY INSPECTION
01-2 PROCEDURES
8.Check security of battery carrier clamps and 
positive battery terminal. Using a volt meter, 
ensure battery voltage exceeds 12.65 volts 
before connecting Testbook/T4. If voltage is 
below this figure recharge battery.
NOTE: The voltage check must be carried out 
before connecting Testbook/T4. Failure to do 
this may result in vehicle configuration failure. 
9.If BBUS multiplug is disconnected, remove nut 
securing sounder to support bracket.
10.Connect multiplug to BBUS.
11.Fit nut to BBUS and tighten to 10 Nm (7 lbf.ft).12.Visually check brake fluid level is at the MAX 
mark on brake reservoir. Investigate the cause 
if brake fluid level is low.
13.Remove filler cap, check and top up 
windscreen, headlamp and rear washer 
reservoir with diluted Land Rover screen wash 
fluid. Refit the cap. 
						

							PRE-DELIVERY INSPECTION
PROCEDURES 01-3
14.Connect earth lead to negative battery terminal 
and tighten bolt to 10 Nm (7 lbf.ft).
15.Start engine, turn the steering fully from lock to 
lock and back to the straight ahead position. 
This action is required to extinguish the 
Steering Angle Sensor (SAS) and Dynamic 
Stability Control (DSC) warning lamps. Stop the 
engine.16.Release cover from drivers side vehicle 
diagnostic socket and connect the Testbook/T4 
lead (DTC 0065A). Connect lead to Testbook/
T4 and switch on.
17.After Testbook/T4 has established 
communication with the vehicle, navigate to the 
Pre Delivery Inspection (PDI) button. Select 
PDI button and follow the Testbook/T4 
programme. Release vehicle from transit 
mode, configure vehicle to market, set 
customer and dealer options (including satellite 
navigation languages if necessary).
18.Disconnect Testbook/T4. 
						

							PRE-DELIVERY INSPECTION
01-4 PROCEDURES
19. Telephone handset registration: The 
following describes the process for registering 
a new phone to a vehicle. Again, it should be 
remembered that only one phone can be 
registered to a vehicle and that any other phone 
should be de-registered prior to trying to 
register a new phone. 
20.Replacement handsets will be supplied from 
the manufacturer in German. Language 
changes can only be made once the phone is 
registered to the vehicle, therefore the 
registration process for new phones must be 
completed in German.
aThe Ignition on and phone must be switched 
on for a minimum of 10 seconds. It is not 
necessary to have the SIM card inserted to 
register a handset.
bThe handset display will show “BITTE 
ANMELLDEN” (PLEASE REGISTER).
cTurn the ignition “OFF” and remove the 
phone from the eject box.
dSwitch the eject box switch to position O 
within 10 seconds.
eTurn the eject box switch to position I within 
5 seconds.
fPress the “OK” button on the handset, the 
handset should display “GERATE CODE” 
(ENTER CODE).
gEnter 0000 and press the “OK” button.
hThe handset will display “ANMELLDEN 
LAUFT” when registered.
iThe handset will then display “BITTE 
SETTEN SIE IHREKARTEIN” (PLEASE 
INSERT THE SIM CARD).
21. Change the telephone handset language: 
Once the registration process is complete the 
handset language may need to be changed. 
aWith the SIM card in and the ignition in 
position 1, turn on the handset.
bThe handset will display “SUCHE BASIS” 
(SEARCHING BASE)
cWhen the service provider is displayed on 
the handset, press the “MENU” button. 
Press 7 to select option 7 in the menu. 
dThe display will show “SPRACHE”, press 
“OK”.
eHighlight the desired language and press 
“OK”.
fReturn to main menu.22. Synchronise the vehicle alarm handsets: 
Ensure the vehicle is unlocked and the driver 
and passenger doors are closed.
23.Insert a key/remote handset in the ignition 
switch, turn the ignition switch to position 1 and 
back to position 0 in less than 5 seconds to put 
the BCU into initialisation mode. Continue the 
next procedure within 30 seconds of turning the 
ignition switch to position 0.
24.Remove the handset from the ignition switch.
25.Press and hold the unlock button then, within 
10 seconds, press the lock button 3 times
26.Release both buttons.
27.Successful initialisation is indicated by the BCU 
locking and unlocking the vehicle. If this does 
not occur, repeat the previous steps.
28.With the remaining handsets, press and hold 
the unlock button, then within 10 seconds, 
press the lock button 3 times. Begin the 
initialisation of each handset within 30 seconds 
of completing the previous initialisation. Failure 
to achieve this will result in the BCU dropping 
out of initialisation mode and the complete 
procedure will have to be started again.
29.Remove all internal, external transit protection 
and brake disc covers. Pay particular attention 
to areas where transit protection is damaged or 
missing. 
						

							PRE-DELIVERY INSPECTION
PROCEDURES 01-5
Vehicle Interior
1. Models fitted with Hi Line Multi Function 
Display (MFD) only: Set time, date and radio 
audio settings, including presets.
2.Turn key in ignition switch to position 1.
3.Switch on the MFD.
4.Depress the menu button, using the right rotary 
control select clock and set time by depressing 
the right rotary control, follow the on screen 
icons. Enter correct time in either 12 or 24 hour 
mode. Press menu to exit clock mode.5.Set 6 FM and 6 AM radio presets.
6.Press the FM button then press Select, rotate 
the right hand rotary control to position 1 
Search Non Sensitive.
7.Press the FM button to display menu of 
selected stations, rotate the right hand rotary 
control and select a station to preset. Allocate a 
preset number to the selected station, depress 
the relevant preset button and hold for 8 
seconds, the station will mute, resumption 
signifies a successful preset.
8.Repeat the procedure for the 5 remaining FM 
presets.
9.Press the AM select button and preset 6 of a 
possible 18 stations by repeating the process 
used to set the FM station presets.
10. Models fitted with Mid Line Multi Function 
Display (MFD) only: Set time, date and radio 
audio settings including presets.
11.Turn key in ignition switch to position 1.
12.Switch on the MFD.