Land Rover Range Rover In Car Entertainment Lm 2nd Edition Rover Manual

General Operation
10
Modifying an individual sound memory
You can modify sound memories 1 to 3 as 
preferred. Adjust the controls for Equaliser, 
Room and Echo.
NOTE: Adjustment of the sound via TONE (4), 
may restrict the range of the individual sound 
memories if the treble or bass settings are 
extremely high or low.
To derive optimum benefit from the sound 
memories, you should first reset the tone 
settings. (See previous page).
Press the DSP button (6).
Press the function key (13) below ‘MEMORY 1,2...

11
General Operation
CLOCK
(Vehicles NOT equipped with Satellite 
Navigation).
NOTE: For safety reasons, only make inputs 
while the vehicle is stationary.
To display time or date
Press the ‘CLOCK’ button (11).
The time can be displayed in 12 or 24 hour 
format and the date in imperial order.
To change the format, press the function key (13) 
below ‘12H’ or ‘24H’ (14). (In 12-hour mode, AM 
or PM appears after the time).
To display date, press the function key (13) 
below ‘DATE‘ (14).
Adjusting and...

General Operation
12
Adjusting and setting the date
Press the ‘CLOCK’ button (11).
Press the function key (13) below ‘DATE’ (14) 
and then the function key (13) below ‘SET’ (14).
To adjust the date, press or hold down the 
function key (13) below ‘DAY’, ’MONTH’ or 
‘YEAR’ (14).
To set the date, press the function key (13) below
‘SET’ (14).
Reminder signal
An hourly reminder signal (MEMO), can be 
programmed, to alert you for example of news 
broadcasts.
Press the ‘CLOCK’ button (11).
To set the reminder...

13
General Operation
Auxiliary heater/independent ventilation 
control* 
NOTE: The auxiliary heater/ventilation function 
can only be accessed in ignition key position 1.
Entering switch-on times
Two different switch-on times can be 
programmed. After 30 minutes, the heating and 
ventilation shut down automatically.
Press the ‘CLOCK’ button (11).
Press the function key (13) below ‘1 TIMER 2’ 
(14). Press the function key (13) below ‘SET’ 
(14).
To input the switch-on time, press or hold down 
the...

Computer Functions
14
Comp ute r Fun ction s
Comp uter Fun ctionsCOMPUTER FUNCTIONS*
3. Display
Displays information on waveband, name of RDS 
stations, programme, frequency, DSP sound 
memory, cassette, MD and CD functions, tone 
settings, time and date.
10. Computer information
Press to access the computer functions.
13. Function keys
Press to select functions from the display (14).
14. Function Key Display
Displays functions and options assigned to the 
Function keys (13). These vary according to the...

15
Computer Functions
COMPUTER FUNCTIONS*
Selecting units of measurement
NOTE: For safety reasons, make inputs only 
while the vehicle is stationary.
The computer calculates and memorises data 
from the start of the journey onwards.
Information can be displayed either in metric or 
imperial units of measurement.
Press the ‘COMPUTER INFORMATION’ button 
(10).
Press the function key (13) below ‘MLS’ or ‘KMS’ 
(14) to select the desired measurement units.
Speed limit
In this function, a signal can be...

Computer Functions
16
Adjusting and setting distances
Press the ‘COMPUTER INFORMATION’ button 
(10).
Press the function key (13) below ‘DIST’ (14).
Press the function key (13) below ‘SET’ (14).
To input the desired distance, press the function 
keys (13) below the required digits (14).
To adjust or correct the setting, press the 
function key (13) below ‘CLR’ (14) and repeat the 
above process.
To store the distance value, press the function 
key (13) below ‘SET’ (14).
It is possible to check the stored...

17
Computer Functions
Speed
The average speed of the vehicle can be 
calculated and displayed.
With the engine running, press the ‘COMPUTER 
INFORMATION’ button (10).
To display the average speed, press the function 
key (13) below ‘SPEED’ (14).
To recalculate the average speed, press the 
function key (13) below ‘SET’ (14).
Extended immobiliser function
With the ignition key in position 1 or 2, a code 
can be entered. The code must be input on future 
occasions before the engine can be started.
If you...

Computer Functions
18
Turn the starter switch to position ‘II’. The 
on-board computer will display a 10 minute 
counter. When the 10 minute count is 
completed, the engine can be started and a new 
code activated, if required.
NOTE: The starter switch MUST remain in 
position ‘II’ throughout the 10 minute count.
Remote control
The silver button at the end of the direction 
indicator stalk can be used to select the 
computer information. When computer 
functions are called up, the message centre in the...

19
Radio Operation
R adio OperationRADIO CONTROLS
3. Display
Displays information on waveband, name of RDS 
stations, programme, frequency, DSP sound 
memory, cassette, MD and CD functions, tone 
settings, time and date.
4. TONE Button
Press to alter settings for: Tone, 
Speed-dependent volume control, Volume of 
traffic reports, and Programme type display.
13. Function keys
Press to select functions from the display (14).
14. Function Key Display
Displays functions and options assigned to the 
Function...