Land Rover Range Rover In Car Entertainment Aus Rover Manual

							Radio Tuning
9
RADIO TUNING
If you know the frequency of the radio
station you are seeking, or you need to select
a radio station that is too weak to be found
by automatic tuning, use manual tuning, as
follows:
Select the desired waveband (FM or AM),
then press the MAN button (6). By briefly
pressing either tuning button (5), the
frequency changes (either up or down) in
steps of 0.1 MHz for FM, or 9 kHz for AM.
Fast manual tuning
By keeping either manual tuning button
depressed, the waveband is scanned rapidly
(up or down) until the button is released.
Automatic tuning
Select the required waveband (FM or AM),
then briefly press one of the tuning buttons
(5) - (SEEK along with the chosen
waveband appear in the display).
The radio automatically searches the
frequency range (either up or down
depending upon which button is pressed)
looking for a station of acceptable strength.
The search then stops unless you choose to
continue by pressing the tuning button
again.
The search can be stopped at any time by
pressing any pre-set button.
Local radio stations
Reception of most local radio stations is
intentionally limited to a comparatively small
area around the transmitter.
8ICE010365
Waveband scan
Select the desired waveband (FM or AM) and
press the SCAN button (8). The radio scans
through the waveband, seeking stations of
acceptable strength (the waveband,
frequency and SC are displayed). The radio
stops at each one it finds and plays that
station for 5 seconds, the radio then mutes
and scans for the next station.
To stop the scan, press the button again -
the radio commences playing the station at
which the scan was stopped.
NOTE:If you have a car telephone with a
mute signal output connected to the radio,
the radio automatically mutes when the
telephone is in use.
MONO/STEREO
Whenever the FM waveband is selected, the
radio automatically reproduces stereo sound,
provided a suitable signal is available.
However, if a signal becomes too weak for
good stereo reception, only mono sound is
produced until the signal strengthens
sufficiently for stereo sound reproduction. 
						

							Radio Pre-sets
10
743ICE0104
RADIO PRE-SET BUTTONS
The six pre-set buttons (7) can be used to
manually store up to twelve FM stations (six
each on FM1 and FM2) and twelve AM
stations (six each on AM1 and AM2). The
pre-sets are programmed as follows:
Programming the pre-sets
·Select the required waveband (FM1, FM2,
AM1 or AM2).
·Tune to the desired frequency using
either automatic or manual tuning.
·Press and hold one of the pre-set buttons
until a bleep sounds. The frequency is
now stored (the display shows the
waveband and frequency or name of the
station to which you have tuned).
NOTE:Once the pre-sets have been
programmed, they will be retained by the
unit until they are re-programmed or until the
battery is disconnected.
Operating the pre-sets
Once the pre-set buttons have been
programmed, operation is simple; select the
desired waveband, then press the pre-set
button of your choice. 
						

							Auto-store
11
743ICE0104
AUTO-STORE
Auto-store enables you to rapidly tune and
store the strongest FM and AM radio signals
in a single operation. This facility is
particularly useful if you are in an unfamiliar
area and have little knowledge of local
transmitter frequencies.
Programming auto-store
Press and hold the appropriate waveband
selection button (3 or 4) until a bleep sounds
(the radio mutes and the display shows
either FM AUTOSTORE or AM
AUTOSTORE).
Auto-store scans the waveband to find the
six strongest frequencies and then stores
them on either the FM2 or AM2 pre-set
buttons in order of signal strength.
NOTE:Auto-store overwrites any stations
already stored on the FM2 or AM2 pre-set
buttons.
Radio play resumes when the operation is
complete.
NOTE:If auto-store is unable to find six
strong stations, the remaining pre-set
buttons remain blank.
Operating auto-store
To tune to one of the auto-store frequencies,
select FM2 or AM2, then press the pre-set
button of your choice; the frequency or radio
station name appears on the display. 
						

							Radio Reception
12
Distortion, interference and lack of signal
clarity, are often attributed to a fault in the
radio - this is rarely the case.
Problems of this kind are usually caused by
phenomena such as atmospheric conditions,
signal strength, hilly terrain, tall buildings,
bridges and even electrical interference from
power lines.
Please remember:A car radio receives
signals while the vehicle is in motion (unlike
a domestic set) - constantly changing
direction and moving away from, or nearer
to, the transmitter whilst negotiating terrain
with widely differing reception
characteristics. Some interference is to be
expected from time to time.
FM transmitters can only broadcast over a
limited range and good, clear signals will
only be received in the immediate area of the
transmitter. When travelling, it may benecessary to re-tune the radio from time to
time, to offset the effects of moving from
one transmitter area to another.
The broadcast range for good stereo
reception (usually within a 30 to 40 mile
radius of the transmitter) is noticeably less
than it is for mono.
FM Signals (like light waves) travel in a
straight line, so large obstacles, such as tall
buildings, can shield the car from the signal
causing distortion or loss of reception
(known as dead spots).
Distortion can also occur if FM signals
received directly from the transmitter mix
with signals which have been reflected by
obstructions such as mountains, hills and tall
buildings (this is known as multi-path
distortion).
ICE 0052  
						

							Care of Cassette Player and Tapes
13 ICE 0054
Use only good quality tapes with a maximum
capacity of ninety minutes (C90). Check that
both spools rotate freely and remove any
loose turns at the start of the tape by winding
one spool with a pen or pencil.
Cassette player
In use, the tape head accumulates dust and
contamination, gradually impairing sound
reproduction and, in extreme cases, reducing
volume too. To combat contamination, clean
the tape head periodically (after
approximately every 20 hours playing time)
by passing a wet type cleaning cassette
through the player.
NOTE:Because your cassette player is fitted
with auto reverse, the cleaning cassette must
be played in both directions.
The tape will require more frequent cleaning
in winter, as contamination is greater in
conditions of low temperature and increased
humidity. However, the use of good quality
tapes, keeps the build up to a minimum.Cassette tapes
·Always store cassettes in their boxes
when not in use.
·Never leave cassettes in the vehicle
during extremes of temperature. In
particular, do not leave tapes in direct
sunlight as they may warp and become
unuseable, or jam the tape player
mechanism.
·Fast forward, or rewind tapes every 8 to
10 plays to prevent them from becoming
too tightly wound.
·Ensure that labels attached to the cassette
are glued firmly in place.
·DO NOT leave tapes in the cassette player
for more than a few hours in very cold or
humid conditions - the oxides on the tape
surface may contaminate the cassette
player mechanism.
NOTE:After continuous playing, cassettes
may become hot to touch. This is normal
and will not harm good quality tape. 
						

							CD Autochanger & Discs
14
ICE0096231
COMPACT DISC CHANGER UNIT (if fitted)
Removing/inserting the magazine
Fully open the sliding cover (1) to insert or
remove the magazine. Keep the cover closed
at all other times to prevent dust and dirt
from entering the changer unit.
Press the button (2) to eject the magazine.
Insert the magazine (3) in the direction of the
arrow marked on the magazine casing and
push it fully into the changer. Finally, close
the sliding cover.
ICE0097
3
Loading & unloading the magazine
Holding the magazine as shown (arrow
uppermost), remove each CD tray in turn.
Place a disc (label side uppermost) onto
each tray - holding ONLY the outside edge
and centre hole of the disc. Load only one
disc in each tray. Correctly align the tray with
the parallel slots on each side of the
magazine and slide the tray into the
magazine.
To unload the magazine, hold the magazine
with the arrow uppermost, pull out each tray
in turn, holding the tray securely so as not to
drop the disc. Unload one disc at a time and
handle only the edge and centre of the disc.
ICE0043 
						

							Caring for Compact Discs
15 IMPORTANT
·Use standard 12cm CDs only.
·DO NOT use irregularly shaped or
damaged CDs - these may damage
the compact disc changer.
·8cm CD singles must NOT be used,
even if a CD adaptor is fitted.
·The CD autochanger should not be
used in temperatures outside the
range -10
°Cto+60°C.
·In th unlikely event that the CD
autochanger overheats, CD OVER
TEMP will be displayed - change to
radio or tape mode until the unit has
cooled.
·The CD autochanger should only be
used as described - any other
application or method of use could
result in the user being exposed to
invisible laser radiation exceeding the
limit of laser class 1.
NOTE:Additional magazines can be
obtained from a Land Rover dealer.CARING FOR COMPACT DISCS
Dirt, dust, condensation and heat can
damage discs. Always observe the following
precautions:
NEVERtouch the horizontal playing surface
(the unlabelled side) of a disc! Handle discs
by holding the outer edges, or the edge of
the central hole and the outer edge, between
finger and thumb.
ALWAYSreturn discs to their boxes after use
(dirt detracts from the sound quality).
NEVERleave the disc or the box exposed to
excessive heat or direct sunlight!
NEVERuse a solvent or abrasive cleaner!
Dust or dirt should be removed from the
playing surface by wiping with a clean, dry,
lint-free cloth always wipe in a straight line
from the centre to the edge of the disc! 
						

							Security Code
16
SECURITY CODE INFORMATION
NOTE:Your vehicle was delivered with the
security code disabled, if you wish to have
the code activated, consult your Land Rover
dealer.
To reduce the risk of theft, Range Rover
radio/cassette and CD players are
programmed with a four digit security code.
Once activated, this code prevents the unit
from functioning if it is illegally removed
from the vehicle. There are 10,000 different
codes - making your radio equipment
valueless to a thief unless he has the correct
one. In addition, each unit is further
protected by a time delay penalty system that
effectively defies even the most systematic
attempt to break the code.
NOTE:If an incorrect code is entered, a one
minute time delay is imposed before a
second code can be attempted. Each time a
wrong code is entered, the time delay
doubles (2 min, 4 min, 8 min, etc.) making
theft a very unattractive proposition.The vehicle was supplied with a Security
Information card. This card contains a record
of the four digit security code, as well as the
units unique serial number. The serial
number is also stamped into the metal side
of the unit and, in the event of theft, would
confirm proof of ownership.
It is VERY IMPORTANT that you keep a safe
record of the security code and heed the
following advice:
·NEVER keep a record of the security code
in the vehicle.
·PLEASE stick the security warning
stickers where the potential thief is sure
to see them, but where they do not
impede your vision of traffic and
pedestrians.
·If you lose your code number, contact the
nearest Land Rover dealer, who will be
able to obtain this information for you. 
						

							Security Code
17
ICE0106
ENTERING THE SECURITY CODE
If the code has not already been entered, or
power to the set has been interrupted, the
code MUST be entered before the set will
operate. Enter the code as follows:
·Switch on the radio (CODE appears in
the display). Press pre-set button 1.
·Press either the up or down tuning button
(highlighted in illustration) until the first
digit of the security code appears in the
display. Press pre-set 1 to store the first
digit in the units memory.
·Use either tuning button to select the
second digit of the code (correct digit
appears in the display). Press pre-set 1 to
store the second digit.
·Select the third digit, again using the
tuning buttons (until the correct digit is
displayed). Press pre-set 1 to store the
third digit.
·Select the final digit (the display now
shows the full four digit code). Press
pre-set 1 to store the final digit.If the correct code has been selected, a
two-tone bleep sounds and the radio will
operate.
NOTE:If an incorrect code has been entered,
the first time delay period commences.
During the delay period, WAIT appears in
the display - DO NOT switch off. At the end
of the delay period, CODE reappears in the
display and you can then enter the correct
code. Remember; the time delay period
doubles each time an incorrect code is
entered.