Land Rover Range Rover Classic Workshop 1995 Rover Manual

INTRODUCTION
9
INFORMATION
D.Connect other end of second jumper cable to a
good earth point on the engine,NOT TO
NEGATIVE TERMINAL OF DISCHARGED
BATTERY.Keep jumper lead away from moving
parts, pulleys, drive belts and fan blade
assembly.
WARNING: Making final cable connection
could cause an electrical arc which if
made near battery could cause an
explosion.
3.If booster battery is installed in another vehicle,
start engine and allow to idle.
4.Start engine of vehicle with discharged battery,
following...

01INTRODUCTION
10
INFORMATION ABBREVIATIONS AND SYMBOLS USED IN THIS
MANUAL
Across flats (bolt size) AF............................................
After bottom dead centre ABDC...................................
After top dead centre ATDC.........................................
Alternating current a.c..................................................
Ampere amp................................................................
Ampere hour amp hr....................................................
Before...

INTRODUCTION
11
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (AC)....................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position...

01INTRODUCTION
12
INFORMATION VEHICLE IDENTIFICATION NUMBER (VIN)
The Vehicle Identification Number and the
recommended maximum vehicle weights are stamped
on a plate located under the bonnet [hood] riveted to
the front of the engine compartment.
Vehicle Identification Number Plate (UK, Australia,
R.O.W., Europe)
A.Build date (Australia). Type approval
B.VIN (17 digits)
C.Maximum permitted laden weight for vehicle
D.Maximum vehicle and trailer weight
E.Maximum road weight-front axle
F.Maximum road...

INTRODUCTION
13
INFORMATION European vehicle identification number (VIN)
Stamped on the right hand side chassis forward of
rear wheel.
Federal (USA) vehicle identification number
Stamped on a plate rivetted to the upper left hand A -
post, visible through the front screen of the vehicle.Vehicle identification number (VIN)
An adhesive label containing the Vehicle Identification
Number, date of manufacture and gross axle weight
ratings is fixed to the lock face of the front left hand
door. The information...

01INTRODUCTION
14
INFORMATION LOCATION OF IDENTIFICATION NUMBERS
Engine serial number - V8i engine
Stamped on a cast pad on the cylinder block, between
numbers 3 and 5 cylinders.
Engines are identified by the prefix:
3.9 Litre:
35D. - 9.35:1 compression, manual transmission
36D. - 9.35:1 compression, automatic transmission
37D. - 8.13:1 compression, manual transmission
38D. - 8.13:1 compression, automatic transmission
4.2 Litre:
40D. - 8.94:1 compression, automatic transmission
Engine serial number -...

INTRODUCTION
15
INFORMATION Transfer gearbox-Borg Warner
Stamped on a plate attached to the gearbox casing,
between filler/level and drain plug.
Front and rear axle
Stamped on the top of the left hand axle tubes. 

01INTRODUCTION
16
INFORMATION FAULT DIAGNOSTIC EQUIPMENT
TESTBOOK
Todays Land Rover Vehicles are equipped with a
large amount of electronics to provide the best
performance of the vehicles systems.
Diagnostic equipment named TESTBOOK is available
to expand the diagnostic abilities of the dealer
workshop. This repair manual is produced with
Testbook in mind.
Features of Testbook include: - Fully upgradable
support for the technician. Structured diagnostics to
accommodate all skill levels. Touch screen...

GENERAL SPECIFICATION DATA
1
INFORMATION ENGINE - V8
Type 3.9 litre V8.................................................................................
Number of cylinders Eight, two banks of four.........................................................
Bore 94.00 mm.................................................................................
Stroke 71.12 mm...............................................................................
Capacity 3950 cm...

04GENERAL SPECIFICATION DATA
2
INFORMATION Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0.018-0.041 mm...................................
Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Molybdenum barrel faced.....................................................
No 2 compression ring Tapered and marked T or...