Land Rover Lr3 Audio Handbook Rover

31
Controls & Settings
R
Navigation Volume Offset*
The Nav Volume Offset allows you to set an 
independent level for the volume of Navigation 
announcements.
To access the Nav Volume Offset settings, 
press the Tone button for approximately five 
seconds until the AVC Level setting is 
displayed. Use short presses of the Tone button 
to scroll through the menu until Nav Volume 
Offset’ is displayed.
The current Nav Volume Offset value will be 
displayed. Use the rotary control to increase or 
decrease...

32
Controls & Settings
R
Voice Volume*
The Voice Volume  allows you to set an 
independent level for the volume of the unit’s 
voice output.
To access the Voice Volume  settings, press 
the Tone button for approximately five seconds 
until the AVC Level setting is displayed. Use 
short presses of the Tone button to scroll 
through the menu until Voice Volume  is 
displayed.
The current Voice Volume  value will be 
displayed. Use the rotary control to increase or 
decrease the value.Reset Volume Settings...

33
Controls & Settings
R
TONE AND BALANCE ADJUSTMENT
Tone and Balance adjustment
To access the Bass setting, press the Tone 
button briefly. When the current Bass setting is 
displayed, use the rotary control to increase or 
decrease the level.
To access the Treble setting, press the Tone 
button repeatedly until the current Treble 
setting is displayed. Use the rotary control to 
increase or decrease the level.To access the Balance setting, press the Tone 
button repeatedly until the current Balance...

34
Controls & Settings
R
To access the Subwoofer setting, press the 
Tone button repeatedly until the current 
Subwoofer setting is displayed. Use the rotary 
control to increase or decrease the setting.To access the LOGIC7 setting, press the Tone 
button repeatedly until the current LOGIC7 
setting is displayed. Use the rotary control to 
highlight ‘Yes’ or ‘No’ as required.
Press the Tone button to confirm your choice.
To access the Source Tone Memory setting, 
press the Tone button repeatedly until...

35
Controls & Settings
R
Resetting Tone Values
To return the tone settings to the factory 
defaults, press the Tone button repeatedly until 
Reset Tone Settings is displayed. Use the 
rotary control to scroll between ‘Yes’ and ‘No’, 
then press the rotary control when your choice 
is highlighted.
Reset Tone  SettingsNo123456
Reset Tone  SettingsYe s123456
ICE1621 ENG 

36
Controls & Settings
R
CLOCK
Adjusting clock
Access the clock set menu by pressing the 
‘Menu/OK’ button. Use the rotary control to 
scroll to ‘Clock’, then press the control to 
select. Rotate the control to scroll between ’12’ 
and ‘24’, then press the control to select the 
required format. To adjust the hours, rotate the control 
clockwise to increase, or anti-clockwise to 
decrease. Press the rotary control to accept the 
value shown.
Once the hours have been set and accepted, the 
minutes will be...

37
Auxiliary Connections*
R
Auxiliar y Connections*
AUXILIARY EQUIPMENT 
CONNECTIONS
AUX (Auxiliary Input) mode allows additional 
equipment to be connected to the vehicle’s 
audio system. Items such as a personal stereo, 
MP3 player, hand-held navigation unit etc. can 
be plugged in to the vehicle’s audio system.The auxiliary connector is situated at the rear of 
the centre console. To gain access, lift the lower 
edge of the cover.
Auxiliary devices can be connected via the 
3.5 mm stereo jack plug....

38
Auxiliary Connections*
R
Auxiliary Mode
To listen to an auxiliary input source, connect 
the device and briefly press the ‘AUX’ button. 
Alternatively, press and hold the ‘MODE’ button 
on the steering wheel.
Volume is controlled using the left rotary 
control, and tone settings are as described 
previously.WARNING
•Read the manufacturer’s instructions for 
any device BEFORE it is connected to the 
vehicle’s audio system. Ensure that the 
device is suitable, and comply with any 
instructions regarding...

39
Radio
R
Radio Operation - Premium Audio
RADIO SETTINGS
Information display screen
1.Current wave band selected.
2.Position that the current station is stored 
under, within pre-sets.
3.Station name (only available when RBDS is 
on), and frequency.
4.Clock display.
5.Displayed when searching for a PTY 
station.Waveband selection
To select the FM waveband, press the ‘FM’ 
button briefly. Repeated presses will toggle 
between ‘FM’, and ‘FMA’. The selection will be 
shown in the top left corner of the...

40
Radio
R
Autostore
To autostore FM stations, press and hold the 
‘FM’ button. ‘Autostore’ will be shown in the 
information display and the stations will be 
stored under the pre-set numbers in the order 
that they are found.
To access the stored stations, press the 
required pre-set number briefly.Storing stations manually.
To select a station, press either of the Search 
up or Search down buttons to scan up or down 
to the next available station. Having tuned to the 
desired station, press and hold...