Land Rover Freelander 2003my Electrical Library Rover Manual

DESCRIPTION AND OPERATION
4.96FREELANDER 03MY
HEATED FRONT SCREEN (HFS)
DESCRIPTION
General
The Heated Front Screen (HFS) consists of two heater elements which are embedded into 
the LH and RH sides of the windscreen. Two connectors at the base of the windscreen 
provide the power feed and an integral earth for each of the heater elements.
Operation of the HFS is controlled by the CCU and a non latching switch on the centre 
console. The switch contains an LED which illuminates while the HFS is on. The...

DESCRIPTION AND OPERATION
FREELANDER 03MY 4.97
HFS Switch
The CCU (C0429) monitors the condition of the HFS switch (C0131) by providing a feed on 
a KO wire. When the switch is pressed the CCU senses the momentary earth path, and 
(providing all other conditions are met) energises the HFS relay. The switch (C0131) is 
earthed on a B wire.
HFS Elements
The energised HFS relay (C0994) provides a feed to fuse A and fuse B (C1860) on a pair of 
NW wires. Fuse A (C1860) provides a feed to the LH screen...

DESCRIPTION AND OPERATION
4.98FREELANDER 03MY
WIPERS AND WASHERS
DESCRIPTION
Front
Wipers
Operation of the windscreen wipers is controlled by the Central Control Unit (CCU). There 
are four modes of wiper operation. These are selectable from the RH column stalk when the 
ignition switch is in the ignition position.
NOTE: Windscreen wiper operation is temporarily suspended while the engine in cranking.
The modes of windscreen wiper operation are:
zSlow wipe.
zFast wipe.
zIntermittent wipe.
zFlick wipe....

DESCRIPTION AND OPERATION
FREELANDER 03MY 4.99
Washer
The rear washer is operated by pressing the non-latching switch mounted on the RH side of 
the instrument pack. The washer will operate until the switch is released.
The rear wiper will start operating at slow speed as soon as the washer switch is depressed, 
and will continue to operate at slow speed for approximately 6 seconds after the switch is 
released.
OPERATION
Front
General
Feed from the positive battery terminal (C0192) is supplied to...

DESCRIPTION AND OPERATION
4.100FREELANDER 03MY
Fast Wipe
Fuse 3 of the passenger compartment fuse box (C0580) provides an ignition feed to the 
wiper switch (C0035) on a G wire. When the wiper switch is moved to the fast wipe position, 
current flows across the switch (C0035) to the wiper motor (C0030) on a RG wire. Current 
flows across the motor fast speed windings and is earthed (C0030) on a B wire. 
Park
Fuse 3 of the passenger compartment fuse box (C0582) provides an ignition feed to the 
wiper...

DESCRIPTION AND OPERATION
FREELANDER 03MY 4.101
Wiper
The CCU (C0592) monitors the condition of the wiper switch (C0079) by providing a feed via 
the passenger compartment fuse box (C0589) on an RG wire. When the switch is pressed, 
current flows across the switch contacts (C0079) to earth on a B wire. When the CCU 
registers this earth, it provides a feed to the rear wiper relay (C0124) on a YB wire. The rear 
wiper relay contains two independent relays; a forward relay and a reverse relay. 
The...

DESCRIPTION AND OPERATION
4.102FREELANDER 03MY
When the CCU receives this feed, it initiates its programmed wash/wipe function, and 
provides a feed to the rear wiper relay (C0124) on a YB wire. The rear wiper relay operates 
the rear wiper as described above.
The rear wiper relay (C0124) also provides a feed to the washer pump relay (C0936) on a 
GR wire. This energises the washer pump relay, which is earthed on a B wire. The energised 
washer pump relay (C0936) provides a feed to the washer pump...

DESCRIPTION AND OPERATION
FREELANDER 03MY 4.103
BRAKE AND REVERSE LAMPS
DESCRIPTION
Brake Lamps
Three brake lamps are fitted to the rear of the vehicle. Two brake lamps are mounted above 
the rear bumper, and share a dual filament bulb with the tail lamps. A third, high mounted 
tail lamp is housed within a casting mounted on the tail door above the spare wheel.
NOTE: NAS vehicles are also fitted with a second pair of brake lamp bulbs. These operate 
in conjunction with the normal brake lamp bulbs. These...

DESCRIPTION AND OPERATION
4.104FREELANDER 03MY
Fuse 2 (C0580) provides an ignition feed to the following on G wires:
zThe reverse lamp relay (C0935) (automatic transmission vehicles only).
zThe brake pedal switch (C0075).
Fuse 2 (C0581) also provides an ignition feed to the reverse lamp switch (C0163) (K1.8 and 
Td4 manual transmission vehicles only) on a G wire.
Brake Lamps
The brake pedal switch (C0075) is provided an ignition feed from fuse 2 of the passenger 
compartment fuse box (C0580) on a G wire....

DESCRIPTION AND OPERATION
FREELANDER 03MY 4.105
Automatic Transmission
Fuse 2 of the passenger compartment fuse box (C0580) provides an ignition feed to the 
reverse lamp relay (C0935) on a G wire. When reverse gear is selected, the Electronic 
Automatic Transmission (EAT) ECU (C0932) provides a feed to the reverse lamp relay coil 
(C0935) on an NG wire. The relay coil (C0935) is earthed on a B wire. The energised reverse 
lamp relay (C0935) is now able to provide a feed to the RH (C0455) and LH (C0472)...