Land Rover Defender Workshop Rover Manual

ELECTRICAL21
REPAIR
MAIN
LIGHT SWITCH
Service repairno-86.65.10
Remove 1. Remove steeringcolumnnacelle
See
STEERING, Repair,Steering columnnacelle.
2.Disconnect mainlightswitch multi-plug from
main harness.
3. Slacken locknutandrelease lightswitch from
slot inmounting bracket.
Refit 4. Fitlight switch inmounting bracket.
5. Reconnect switchmulti-plug.
6. Fitsteering columnnacelle
SeeSTEERING,
Repair, Steering columnnacelle.
HEATED REARSCREEN, REARFOGLAMP AND
HAZARD WARNING SWITCHES
Service...

86ELECTRICAL
22 REPAIR
CIGAR
LIGHTER
Service repairno-86.65.60
Remove
1. Remove 2screws andwithdraw switchpanel
from lower fascia.
2. Disconnect electricalleadsfromswitch housing,
including illumination bulb.
3. Release 2retaining tagsandremove bulbholder
from switch housing.
4. Remove cigarlighter fromswitch housing.
5. Press inretaining tagsandwithdraw housing
from switch panel.
Refit 6. Fithousing toswitch panel.
7. Fitbulb holder toswitch housing.
8. Connect electrical leadsandillumination bulb.
9....

ELECTRICAL23
REPAIR
HEADLAMP
LEVELLINGSWITCH
Service repairno-86.65.16
Remove
1. Remove 2screws andwithdraw switchpanel
from lower fascia.
2. Disconnect multi-plugfromrearofheadlamp
levelling switch.
3. Remove knobfromswitch spindle.
4. Unscrew retainingnutand withdraw switchfrom
switch panel.
Refit 5. Fitswitch intoswitch panelandsecure with
retaining nut.
6. Fitswitch knob.
7. Connect switchmulti-plug.
8. Fitswitch panel. HEADLAMP
LEVELLINGUNIT
Service repairno-86.41.16
Remove 1. Remove headlamp...

86ELECTRICAL
24 REPAIR
HEADLAMP
BEAMALIGNMENT
Service repairno-86.40.17
Check Check mainbeam alignment usingbeam setting
equipment. Shouldthisnotbeavailable thebeam can
be temporarily checkedandadjusted asfollows:-
1. Position vehicle,unladen, onlevel ground with
tyres correctly inflated,approximately 4meters
from awall orscreen, marked asillustrated
below.
2. The beam centres Aare measured horizontally
on the vehicle anddimension Bvertically from
the ground.
3.Switch onmain beam andadjust setting, as...

ELECTRICAL25
REPAIR
DIGITAL
DIESELSHUT-OFF VALVE(DDS)
Service repairno-86.77.00
Remove 1. Remove fuelinjection pump
SeeFUEL
SYSTEM, Repair,Fuelinjection pump.
2.Drill out2shear boltssecuring DDSvalve and
clamp, usinga3.2 mm drill, toadepth of
approximately 5mm.
CAUTION: Useadrill bushing toguide the
drill.
3. Using anextractor, removethe2DDS valve
retaining boltsanddiscard.
4. Release DDSvalve fromfuelshut-off solenoid.
5. Remove protective capfrom shut-off solenoid.
6. Unscrew terminalnut,release...

INSTRUMENTS1
REPAIR
INSTRUMENT
PANEL
Service repairno-88.20.02
Remove 1. Disconnect battery.
2.Remove 4screws securing instrument panelto
fascia cowl.
3. Pull instrument panelawayfromfascia sufficent
to disconnect speedometer cable.
4. Disconnect multi-plugs, electricalleadsand
connections tovehicle alarmsystem, iffitted
See ELECTRICAL, Repair,Vehicle
immobilisation andalarm system
.
5. Withdraw panel,complete withinstruments.
Refit 6. Offer upinstrument panel,connect multi-plugs,
electrical...

88INSTRUMENTS
2 REPAIR
FUEL
ANDTEMPERATURE GAUGE
Service repairno-88.25.26 -Fuel gauge
Service repairno-88.25.14 -Temperature gauge
Remove 1. Remove instrument panel
SeeInstrument
panel
.
2. Release illumination bulbholder anddisconnect
electrical leadsfromgauge.
3. Unscrew knurlednutand remove clamp
securing gauge.
4. Remove earthleadeylet fromgauge stud.
5. Withdraw gaugefrominstrument panel
Refit 6. Fitgauge intoinstrument panel,locateearth
lead, andsecure withclamp.
7. Fitbulb holder andelectrical...

INSTRUMENTS3
REPAIR
CLOCK
-CENTRE DASHPANEL
Service repairno-88.15.07
Remove
1. Remove 2screws andwithdraw switchpanel
from centre dash.
2. Release illumination bulbholder anddisconnect
electrical leadsfromclock.
3. Press inspring retainers andremove clockfrom
panel.
Refit 4. Fitclock intodash panel.
5. Fitelectrical leadsandbulb holder.
6. Secure switchpaneltocentre dash. WARNING
LIGHTPANEL
Service repairno-88.20.18
Remove
1. Remove 2screws andwithdraw warninglight
panel.
2. Disconect bothmulti-plugs....

88INSTRUMENTS
4 REPAIR
PRINTED
CIRCUIT-WARNING LIGHTPANEL
Service repairno-88.20.20
Remove 1. Remove warninglightpanel
See Warning light
panel
.
2. Remove 13illumination bulbholders fromlight
panel.
3. Release printedcircuitfromlocating pinsand
remove frompanel seatings.
Refit 4. Fitnew printed circuitoverpanel seatings and
position onlocating pins.
5. Fitillumination bulbstosecure circuit.
6. Fitwarning lightpanel
See Warning light
panel
. FUEL
GAUGE TANKUNIT-REAR FUELTANK,
110/130 Service...

INSTRUMENTS5
REPAIR
FUEL
GAUGE TANKUNIT-SIDE FUEL TANK
Service repairno-88.25.31
WARNING: Ensurethatfuelhandling
precautions giveninSection 01-
Introduction arestrictly adhered towhen
carrying outthefollowing instructions.
Remove 1. Disconnect battery.
2. Remove RHfront seatcushion.
3. Release retaining catchandremove seatbase
cover togain access tofuel tank.
4.Disconnect electricalplugfrom fuelgauge unit.
5. Release lockingringand withdraw fuelgauge
unit from tank, complete withsealing ring.
Refit 6....