Land Rover Defender 90 Workshop 2nd Edition Nas Rover Manual

86ELECTRICAL
6
REPAIR INTERIOR LAMP - BULB REMOVAL
Service repair no - 86.45.01
Remove
1.Prise lens from lamp unit.
2.Spread bulb holder contacts and release bulb.
Refit
3.Spread bulb holder contacts and fit new bulb.
4.Fit lamp lens.INTERIOR LAMP
Service repair no - 86.45.02
Remove
1.Prise lens cover from lamp unit.
2.Remove 2 nuts securing lamp unit to headlining
and roof mounting bracket.
3.Remove lamp unit from mounting bracket studs
and disconnect harness plug.
4.Remove interior lamp.
Refit...

ELECTRICAL
7
REPAIR WARNING LAMP ASSEMBLY
Service repair no - 86.45.60 - Warning lamp
assembly
Service repair no - 86.45.61 - Warning lamp bulb
renewal
Remove
1.Disconnect battery.
2.Remove 2 screws and withdraw warning light
assembly from instrument panel.
3.Remove multi-plug to give access to warning
lamp bulbs.
4.Twist bulb holder and pull it from its socket.
5.Pull bulb from holder.
Refit
6.Fit new bulb and refit holder.
7.Fit multi-plug.
8.Fit warning lamp assembly to instrument panel
9.Reconnect...

86ELECTRICAL
8
REPAIR STARTER SWITCH
Service repair no - 86.65.03
Remove
1.Remove instrument panel.
See
INSTRUMENTS, Repair, Instrument panel
2.Remove steering column nacelle.
3.Note position of harness leads on back of starter
switch and disconnect lukars.
4.Remove single screw and withdraw starter
switch from steering column lock.
Refit
5.Fit new switch in steering column lock.
6.Connect harness leads to starter switch.
7.Fit steering column nacelle.
8.Fit instrument panel.
See INSTRUMENTS,
Repair,...

ELECTRICAL
9
REPAIR DIRECTION INDICATOR/HEADLAMP/HORN
SWITCH
Service repair no - 86.65.55
Remove
1.Remove steering column nacelle.
2.Disconnect 3 steering column switch multi-plugs
from main harness.
3.Slacken clamp screw and withdraw switch
assembly from steering column.
4.Remove fixings and detach windscreen
wiper/washer and main lighting switches from
mounting bracket.
5.Renew complete direction
indicator/headlamp/horn switch and switch
bracket assembly.
Refit
6.Fit main lighting and windscreen...

86ELECTRICAL
10
REPAIR SWITCH PANEL - REAR DOOR SERVICES
Service repair no - 86.65.78
Remove
1.Release screw caps from top fixings and remove
screws. Prise out 2 trim studs securing bottom of
switch panel to fascia.
2.Withdraw switch panel and disconnect
multi-plugs from switches and module.
3.Pull harness multi-plugs through aperture in
base of panel.
Refit
4.Feed harness into switch panel and reconnect
multi-plugs.
5.Position switch panel on fascia and secure with
screws and trim studs.HEATED REAR...

ELECTRICAL
11
REPAIR CIGAR LIGHTER
Service repair no - 86.65.60
Remove
1.Remove 2 screws and withdraw switch panel
from lower fascia.
2.Disconnect electrical leads from switch housing,
including illumination bulb.
3.Release 2 retaining tags and remove bulb holder
from switch housing.
4.Remove cigar lighter from switch housing.
5.Press in retaining tags and withdraw housing
from switch panel.
Refit
6.Fit housing to switch panel.
7.Fit bulb holder to switch housing.
8.Connect electrical leads and...

86ELECTRICAL
12
REPAIR HIGH LEVEL STOP LAMP - HARDTOP
Service repair no - 86.41.32
Remove
1.Remove 2 screws and remove stop lamp cover.
2.Disconnect Lucars from bulb holder.
3.Unscrew 2 nuts and remove lamp unit from fixing
studs and rubber gasket.
4.Remove gasket.
Refit
5.Position gasket and stop lamp. Secure with two
nuts.
6.Connect Lukars to bulb holder.
7.Position cover and secure with screws.RADIO SPEAKER - REAR
Service repair no - 86.50.12
Remove
1.Raise rear seat cushion and fit stowage strap....

ELECTRICAL
13
REPAIR GENERATOR
Service repair no - 86.10.02
Remove
1.Disconnect battery negative lead.
2.Remove drive belt.
See Auxiliary drive belt
3.Remove cover from rear of generator.
4.Disconnect Lucar from rear of generator and
collect cover.
5.Remove 2 nuts securing leads to rear of
generator.
6.Disconnect leads from rear of generator.
7.Remove 2 bolts securing generator to mounting
bracket and collect nuts.
8.Remove generator.Refit
9.Fit generator to mounting bracket.
10.Fit bolts and tighten...

86ELECTRICAL
14
REPAIR AUXILIARY DRIVE BELT
Service repair no - 86.10.03
Remove
1.Remove viscous coupling.
See COOLING
SYSTEM, Repair, viscous coupling
2.Release drive belt tension by turning tensioner
clockwise.
3.With tension released, remove belt from
alternator pulley.
4.Remove drive belt.
NOTE: If belt is to be refitted, mark
direction of rotation.
Refit
5.Clean drive belt pulley grooves and inspect for
damage.
6.Fit belt to pulleys.
7.Turn drive belt tensioner clockwise and fit belt to
alternator...

ELECTRICAL
15
REPAIR STARTER MOTOR
Service repair no - 86.60.01
1.Position vehicle on ramp [hoist].
2.Disconnect battery negative lead.
3.Remove RH front heated oxygen sensor.
See
FUEL SYSTEM, Repair, heated oxygen
sensor (H02s)
4.Remove front bolt and loosen rear bolt securing
catalyst heat shield. Lower front edge of heat
shield.
5.Remove bolt securing starter motor heat shield
to RH engine mounting bracket.
6.Release heat shield clip from starter motor
solenoid and move aside for access.
7.Lower ramp...