Land Rover Defender 1999 2002my Workshop Supplement Body Repair 2nd Edition Rover Manual

12ENGINE
16
DESCRIPTION AND OPERATION Oil cooler
1.Front oil gallery - full-flow filter to oil cooler matrix
2.Full-flow filter adaptor outlet port to oil cooler
(opens at 74°C)
3.Full-flow filter inlet port
4.Oil cooler housing
5.Full-flow filter outlet port to cylinder block
6.Coolant inlet port
7.Oil cooler banjo bolt seals (2 off)
8.Banjo bolts (2 off)
9.Banjo bolt oil holes - to oil cooler matrix
10.Rear oil gallery - full-flow filter / oil cooler outlet
to cylinder block11.Centre oil gallery - from...

ENGINE
17
DESCRIPTION AND OPERATION The engine oil cooler assembly is located on the left hand side of the engine block behind the oil centrifuge and oil
filter. The housing is bolted to the engine block by seven bolts. A matrix is included in the oil cooler housing which
acts as a heat exchanger. Coolant flow circulates through the oil cooler housing under pressure from the coolant
pump and distributes the flow evenly around the matrix fins and then along the block into three core holes for
cylinder...

12ENGINE
18
DESCRIPTION AND OPERATION Oil filters
The Td5 engine features two types of oil filter; the main filter is a standard disposable cartridge-type full flow oil
filter which is augmented with a by-pass centrifuge filter used to filter out particulate matter having a smaller
diameter smaller than 15 micron but greater than 3 micron.
1.Centre spindle
2.Spindle oil holes (2 off)
3.Centrifuge filter housing
4.Centrifuge filter drain pipe
5.Port - centrifuge filter drain pipe to sump6.Filter rotor...

ENGINE
19
DESCRIPTION AND OPERATION Full flow filter
Approximately 10% of the total oil flow enters the centrifuge pot through a side port in the pot casting which is
mated to an outlet port at the lower side of the oil cooler housing. A rubber’O’ring sits in a recess around the oil
cooler port which seals the faces between the centrifuge pot and oil cooler port, and it must be replaced every
time the centrifuge assembly is removed. Oil leaves the centrifuge pot through a drain tube which is attached to...

12ENGINE
20
DESCRIPTION AND OPERATION Oil filter housing thermostat
1.Circlip
2.Thermostat end cap
3.Oil seal
4.Thermostatic valve5.Return spring
6.Oil filter housing
7.Threaded insert
The oil filter housing contains a thermostatically controlled valve to control the direction and proportion of oil flow
through the oil cooler matrix. When the oil temperature is cool, the centre spindle of the thermostatic element is
compressed. In this condition the valve completely seals the passage to the turbocharger...

ENGINE
21
DESCRIPTION AND OPERATION Oil pressure switch
The oil pressure switch is located in a port on the outlet side of the oil cooler housing. It detects when a safe
operating pressure has been reached during engine starting and initiates the illumination of a warning light in the
instrument pack if the pressure drops below a given value. 

12ENGINE
22
DESCRIPTION AND OPERATION CRANKSHAFT, SUMP AND OIL PUMP
The crankshaft, sump and oil pump components are described below:
Sump
The sump is a wet-type, of aluminium construction and is sealed to the engine block by means of a rubber gasket
and twenty fixing bolts. The four bolts at the gearbox end of the sump are longer than the other sixteen bolts.
The sump gasket incorporates compression limiters (integrated metal sleeves) at the bolt holes, which are
included to prevent distortion of the...

ENGINE
23
DESCRIPTION AND OPERATION Oil pump
1.Stiffener plate
2.Ring dowel
3.Outlet port
4.Outer rotor
5.Inner rotor6.Spring dowel
7.Oil pressure relief valve cap
8.Oil pressure relief valve spring
9.Oil pressure relief valve plunger
10.Inlet port
The eccentric rotor oil pump is integrated with the stiffener plate and contains no serviceable parts except for the
pressure relief valve spring. The oil pump drive sprocket is attached to the front of the stiffener plate and is driven
through a chain and...

12ENGINE
24
DESCRIPTION AND OPERATION Crankshaft
1.Front end to crankshaft sprocket
2.Oil supply cross-drillings
3.Main journals4.Big-end journals
5.Rear end to flywheel
The crankshaft is constructed from cast iron and is surface-hardened. The areas between the crankshaft journals
and the adjoining webs and balance weights are compressed using the cold roll process to form journal fillets.
Cross-drillings in the crankshaft between adjoining main and big-end bearings are used to divert lubrication oil to...

ENGINE
25
DESCRIPTION AND OPERATION CYLINDER HEAD COMPONENTS
The cylinder head components are described below:
Cylinder head
The cylinder head is of aluminium construction. It is not possible to reface the cylinder head if it becomes worn or
damaged. An alloy camshaft carrier is bolted directly to the upper surface of the cylinder head. Two dowels are
included in the cylinder head upper face for correct location of the camshaft carrier.
The EU3 cylinder head has a single internal fuel rail for delivering...